Alpha snapshot 3.7 hard disk format error
"Roger Neth Jr" <[email protected]> Tue, 02 Aug 2005 15:09:22 -0700
| Newsgroups | gmane.os.openbsd.alpha |
|---|---|
| Message-ID | <[email protected]> |
Hello All,
I have been trying to install the new snapshot for alpha and keep getting
this error.
sd0(isp0:0:0): Check Condition (error 0x70) on opcode 0x2a
SENSE KEY: Illegal Request
INFO: 0x7fdeb0 (VALID flag on)
ASC/ASCQ: Logical Block Address Out of Range
newfs: wtfs: write error on block 8264575: Invalid argument
/dev/rsd1d: 4194304 sectors in 7424 cylinders of 5 tracks, 113 sectors
2048.0MB in 15 cyl groups (512 c/g, 141.25MB/g, 18048 i/g)
/dev/rsd1e: 2088624 sectors in 3697 cylinders of 5 tracks, 113 sectors
1019.8MB in 8 cyl groups (512 c/g, 141.25MB/g, 18048 i/g)
/dev/sd0a on /mnt type ffs (rw, asynchronous, local, ctime=Tue Aug 2
21:56:18 2005)
/dev/sd1e on /mnt/home type ffs (rw, asynchronous, local, nodev, nosuid,
ctime=Tue Aug 2 21:56:18 2005)
/dev/sd0d on /mnt/tmp type ffs (rw, asynchronous, local, nodev, nosuid,
ctime=Tue Aug 2 21:56:18 2005)
mount_ffs: /dev/sd0e on /mnt/usr: Inappropriate file type or format
FATAL ERROR: Cannot mount filesystems. Double-check your configuration
and restart the install.
# halt
I have tried using x * 2048 * 2048 / 2048 to calculate the size but still
same error.
Any help is appreciated,
Thank you,
rogern
Script started on Tue Aug 2 14:55:19 2005
openbsd37# cu -l tty00
Connected
^C
>>>boot show config
Firmware
SRM Console: V7.2-1 Mar 6 2000 14:47:02
ARC Console: 5.70
PALcode: OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode V1.22-18
SROM Version: v5.90
Processor
DECchip (tm) 21164A-2 Pass 500 MHz 96 KBytes SCache
2 MB BCache
PYXIS ASIC Pass 257
MEMORY
Memory Size = 128Mb
Bank Size/Sets Base Addr
------ ---------- ---------
0 128Mb 00000000
BCache Size = 2Mb
Tested Memory = 128Mbytes
PCI Bus
Bus 00 Slot 03: Digital Semiconductor 21143 Network Controller
ewa0.0.0.3.0 00-00-F8-76-73-52
Bus 00 Slot 07: Cypress PCI Peripheral Controller
Bus 00 Slot 07: Function 1: PCI IDE
Bus 00 Slot 07: Function 2: PCI IDE
dqb0.0.0.207.0 TOSHIBA CD-ROM
XM-63
Bus 00 Slot 07: PCI USB
Bus 00 Slot 11: Digital TGA2 Graphics Controller
Bus 00 Slot 20: DECchip 21152 PCI to PCI Bridge
Bus 01 Slot 04: ISP1040 Scsi Controller
pka0.7.0.1004.0 SCSI Bus ID 7
dka0.0.0.1004.0 RZ2CC-KA
dka100.1.0.1004.0 RZ2CC-KB
Bus 01 Slot 08: DE500-BA Network Controller
ewb0.0.0.1008.0 08-00-2B-C3-C9-01
Bus 01 Slot 09: DE500-BA Network Controller
ewc0.0.0.1009.0 08-00-2B-C3-C3-D8
ISA
Slot Device Name Type Enabled BaseAddr IRQ DMA
0
0 MOUSE Embedded Yes 60 12
1 KBD Embedded Yes 60 1
2 COM1 Embedded Yes 3f8 4
3 COM2 Embedded Yes 2f8 3
4 LPT1 Embedded Yes 3bc 7
5 FLOPPY Embedded Yes 3f0 6 2
6 EIDE Embedded Yes 1f0 14
3f6 15
170
376
7 ES1888 Embedded Yes 220 5 1
5
8 USB Embedded Yes 10
>>>shw ow ps
>>>show ps
ID PCB Pri CPU Time Affinity CPU Program State
-------- -------- --- -------- -------- --- ----------
------------------------
0000007c 00152460 3 0 00000001 0 ps running
00000019 00173440 3 5 00000001 0 shell ready
00000014 0016b060 6 0 ffffffff 0 rx_ewc0 waiting on
rx_isr_ewc0
00000012 00160d20 6 0 ffffffff 0 rx_ewb0 waiting on
rx_isr_ewb0
0000000e 001562e0 6 0 ffffffff 0 rx_ewa0 waiting on
rx_isr_ewa0
00000007 0014a080 3 0 00000001 0 shell_0 waiting on rxq_ready
00000006 00031600 6 1 ffffffff 0 tt_control waiting on tt_control
00000004 0002c8e0 7 44 ffffffff 0 timer waiting on timer
00000003 0002b2e0 2 176084 ffffffff 0 poll ready
00000002 00029d80 6 0 ffffffff 0 dead_eater waiting on dead_beef
00000001 001302b0 0 338725 00000001 0 idle ready
>>>show device
dka0.0.0.1004.0 DKA0 RZ2CC-KA 5520
dka100.1.0.1004.0 DKA100 RZ2CC-KB DC2B
dqb0.0.0.207.0 DQB0 TOSHIBA CD-ROM XM-6302B 1017
dva0.0.0.0.1 DVA0
ewa0.0.0.3.0 EWA0 00-00-F8-76-73-52
ewb0.0.0.1008.0 EWB0 08-00-2B-C3-C9-01
ewc0.0.0.1009.0 EWC0 08-00-2B-C3-C3-D8
pka0.7.0.1004.0 PKA0 SCSI Bus ID 7 5.57
pqa0.0.0.107.0 PQA0 PCI EIDE
pqb0.0.0.207.0 PQB0 PCI EIDE
>>>boot DQB0
(boot dqb0.0.0.207.0 -flags a)
block 0 of dqb0.0.0.207.0 is a valid boot block
reading 15 blocks from dqb0.0.0.207.0
bootstrap code read in
base = 1d8000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 1ca000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
OpenBSD/Alpha Primary Boot
.....................OpenBSD/Alpha boot 1.7
VMS PAL rev: 0x1000000010114, OSF PAL rev: 0x1000000020116
Loading bsd...
329448
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.7-current (RAMDISKBIG) #385: Thu Jul 14 20:53:43 MDT 2005
[email protected]:/usr/src/sys/arch/alpha/compile/RAMDISKBIG
Digital Personal WorkStation 500au, 500MHz
8192 byte page size, 1 processor.
total memory = 134217728 (131072K)
(1941504 reserved for PROM, 132276224 used by OpenBSD)
avail memory = 109223936 (106664K)
using 1614 buffers containing 13221888 bytes (12912K) of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21164A-0 (unknown minor type 0)
cpu0: Architecture extensions: 1<BWX>
cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 1
cia0: extended capabilities: 1<BWEN>
cia0: using BWX for PCI config and bus access
pci0 at cia0 bus 0
de0 at pci0 dev 3 function 0 "DEC 21142/3" rev 0x30: dec 550 irq 0
de0: DEC pass 3.0 address 00:00:f8:76:73:52
sio0 at pci0 dev 7 function 0 "Contaq Microsystems CY82C693U ISA" rev 0x00
pciide0 at pci0 dev 7 function 1 "Contaq Microsystems CY82C693U ISA" rev
0x00: DMA, channel 0 wired to compatibility
pciide0: channel 0 disabled (no drives)
pciide1 at pci0 dev 7 function 2 "Contaq Microsystems CY82C693U ISA" rev
0x00: no DMA, channel 0 wired to compatibility
atapiscsi0 at pciide1 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TOSHIBA, CD-ROM XM-6302B, 1017> SCSI0 5/cdrom
removable
cd0(pciide1:0:0): using PIO mode 4
ohci0 at pci0 dev 7 function 3 "Contaq Microsystems CY82C693U ISA" rev 0x00:
isa irq 10, version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Contaq Microsys OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
tga0 at pci0 dev 11 function 0 "DEC TGA2" rev 0x22: TGA2 pass 2, board type
T8-02
tga0: 1024 x 768, 8bpp, Bt485 RAMDAC
tga0: interrupting at dec 550 irq 4
wsdisplay0 at tga0 mux 1
wsdisplay0: screen 0 added (std, vt100 emulation)
ppb0 at pci0 dev 20 function 0 "DEC 21152 PCI-PCI" rev 0x03
pci1 at ppb0 bus 1
isp0 at pci1 dev 4 function 0 "QLogic ISP1020" rev 0x05: dec 550 irq 3
isp0: invalid NVRAM header
scsibus1 at isp0: 16 targets
sd0 at scsibus1 targ 0 lun 0: <DEC, RZ2CC-KA (C) DEC, 5520> SCSI2 0/direct
fixed
sd0: 4091MB, 3708 cyl, 20 head, 113 sec, 512 bytes/sec, 8380080 sec total
sd1 at scsibus1 targ 1 lun 0: <DEC, RZ2CC-KB (C) DEC, DC2B> SCSI2 0/direct
fixed
sd1: 4091MB, 3708 cyl, 20 head, 113 sec, 512 bytes/sec, 8380080 sec total
de1 at pci1 dev 8 function 0 "DEC 21142/3" rev 0x30: dec 550 irq 12
de1: DEC DE500-BA pass 3.0 address 08:00:2b:c3:c9:01
de2 at pci1 dev 9 function 0 "DEC 21142/3" rev 0x30: dec 550 irq 16
de2: DEC DE500-BA pass 3.0 address 08:00:2b:c3:c3:d8
isa0 at sio0
vga0 at isa0 port 0x3b0/48 iomem 0xa0000/131072
wsdisplay1 at vga0 mux 1
wsdisplay1: screen 0 added (80x25, vt100 emulation)
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
WARNING: can't figure what device matches ""
root on rd0a swap on rd0b
rd0: fixed, 5744 blocks
rootdev=0x600 rrootdev=0x1c00 rawdev=0x1c02
WARNING: clock gained 18 days -- CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
(I)nstall, (U)pgrade or (S)hell? i
Welcome to the OpenBSD/alpha 3.7 install program.
This program will help you install OpenBSD in a simple and rational way. At
any prompt except password prompts you can run a shell command by typing
'!foo', or escape to a shell by typing '!'. Default answers are shown in
[]'s
and are selected by pressing RETURN. At any time you can exit this program
by
pressing Control-C and then RETURN, but quitting during an install can leave
your system in an inconsistent state.
Terminal type? [vt220]
IS YOUR DATA BACKED UP? As with anything that modifies disk contents, this
program can cause SIGNIFICANT data loss.
It is often helpful to have the installation notes handy. For complex disk
configurations, relevant disk hardware manuals and a calculator are useful.
Proceed with install? [no] yes
Cool! Let's get to it.
You will now initialize the disk(s) that OpenBSD will use. To enable all
available security features you should configure the disk(s) to allow the
creation of separate filesystems for /, /tmp, /var, /usr, and /home.
Available disks are: sd0 sd1.
Which one is the root disk? (or 'done') [done] sd0
Initial label editor (enter '?' for help at any prompt)
>p m
device: /dev/rsd0c
type: SCSI
disk: RZ2CC-KA
label:
bytes/sector: 512
sectors/track: 168
tracks/cylinder: 20
sectors/cylinder: 3360
cylinders: 3708
total bytes: 6083.4M
free bytes: 0.0M
rpm: 3600
8 partitions:
# size offset fstype [fsize bsize cpg]
a: 1024.0M 0.0M 4.2BSD 2048 16384 384
c: 6083.4M 0.0M unused 0 0
d: 1024.0M 1024.0M 4.2BSD 2048 16384 384
e: 4035.4M 2048.0M 4.2BSD 2048 16384 16
>p
device: /dev/rsd0c
type: SCSI
disk: RZ2CC-KA
label:
bytes/sector: 512
sectors/track: 168
tracks/cylinder: 20
sectors/cylinder: 3360
cylinders: 3708
total sectors: 12458880
free sectors: 0
rpm: 3600
8 partitions:
# size offset fstype [fsize bsize cpg]
a: 2097152 0 4.2BSD 2048 16384 384
c: 12458880 0 unused 0 0
d: 2097152 2097152 4.2BSD 2048 16384 384
e: 8264576 4194304 4.2BSD 2048 16384 16
>q
No label changes.
Mount point for sd0d (size=1048576k)? (or 'none' or 'done') /tmp
Mount point for sd0e (size=4132288k)? (or 'none' or 'done') /usr
Mount point for sd0d (size=1048576k)? (or 'none' or 'done') [/tmp] done
Available disks are: sd1.
Which one do you wish to initialize? (or 'done') [done] sd1
Initial label editor (enter '?' for help at any prompt)
>p m
device: /dev/rsd1c
type: SCSI
disk: RZ2CC-KB
label:
bytes/sector: 512
sectors/track: 113
tracks/cylinder: 20
sectors/cylinder: 2260
cylinders: 3708
total bytes: 4091.8M
free bytes: 0.0M
rpm: 3600
8 partitions:
# size offset fstype [fsize bsize cpg]
b: 1024.0M 0.0M swap
c: 4091.8M 0.0M unused 0 0
d: 2048.0M 1024.0M 4.2BSD 2048 16384 512
e: 1019.8M 3072.0M 4.2BSD 2048 16384 512
>p
device: /dev/rsd1c
type: SCSI
disk: RZ2CC-KB
label:
bytes/sector: 512
sectors/track: 113
tracks/cylinder: 20
sectors/cylinder: 2260
cylinders: 3708
total sectors: 8380080
free sectors: 0
rpm: 3600
8 partitions:
# size offset fstype [fsize bsize cpg]
b: 2097152 0 swap
c: 8380080 0 unused 0 0
d: 4194304 2097152 4.2BSD 2048 16384 512
e: 2088624 6291456 4.2BSD 2048 16384 512
>q
No label changes.
Mount point for sd1d (size=2097152k)? (or 'none' or 'done') /var
Mount point for sd1e (size=1044312k)? (or 'none' or 'done') /home
Mount point for sd1d (size=2097152k)? (or 'none' or 'done') [/var] done
No more disks to initialize.
OpenBSD filesystems:
sd0a /
sd0d /tmp
sd0e /usr
sd1d /var
sd1e /home
The next step *DESTROYS* all existing data on these partitions!
Are you really sure that you're ready to proceed? [no] yes
/dev/rsd0a: 2097152 sectors in 2497 cylinders of 5 tracks, 168 sectors
1024.0MB in 7 cyl groups (384 c/g, 157.50MB/g, 20224 i/g)
/dev/rsd0d: 2097152 sectors in 2497 cylinders of 5 tracks, 168 sectors
1024.0MB in 7 cyl groups (384 c/g, 157.50MB/g, 20224 i/g)
sd0(isp0:0:0): Check Condition (error 0x70) on opcode 0x2a
SENSE KEY: Illegal Request
INFO: 0x7fdeb0 (VALID flag on)
ASC/ASCQ: Logical Block Address Out of Range
newfs: wtfs: write error on block 8264575: Invalid argument
/dev/rsd1d: 4194304 sectors in 7424 cylinders of 5 tracks, 113 sectors
2048.0MB in 15 cyl groups (512 c/g, 141.25MB/g, 18048 i/g)
/dev/rsd1e: 2088624 sectors in 3697 cylinders of 5 tracks, 113 sectors
1019.8MB in 8 cyl groups (512 c/g, 141.25MB/g, 18048 i/g)
/dev/sd0a on /mnt type ffs (rw, asynchronous, local, ctime=Tue Aug 2
21:56:18 2005)
/dev/sd1e on /mnt/home type ffs (rw, asynchronous, local, nodev, nosuid,
ctime=Tue Aug 2 21:56:18 2005)
/dev/sd0d on /mnt/tmp type ffs (rw, asynchronous, local, nodev, nosuid,
ctime=Tue Aug 2 21:56:18 2005)
mount_ffs: /dev/sd0e on /mnt/usr: Inappropriate file type or format
FATAL ERROR: Cannot mount filesystems. Double-check your configuration
and restart the install.
# halt
syncing disks... done
halted.
halted CPU 0
halt code = 5
HALT instruction executed
PC = fffffc0000230118
>>>
_________________________________________________________________
On the road to retirement? Check out MSN Life Events for advice on how to
get there! http://lifeevents.msn.com/category.aspx?cid=Retirement