Re: USB!

On Thu, Nov 23, 2006 at 08:52:51PM +0000, Christian Weisgerber wrote:
> I've added a no-name USB PCI card to my -current AS800.  The card
> is recognized:
> 
> uhci0 at pci0 dev 12 function 0 "VIA VT83C572 USB" rev 0x61: dec_1000a irq 3
> usb0 at uhci0: USB revision 1.0
> uhub0 at usb0
> uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhci1 at pci0 dev 12 function 1 "VIA VT83C572 USB" rev 0x61: dec_1000a irq 4
> usb1 at uhci1: USB revision 1.0
> uhub1 at usb1
> uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> ehci0 at pci0 dev 12 function 2 "VIA VT6202 USB" rev 0x63: dec_1000a irq 19
> usb2 at ehci0: USB revision 2.0
> uhub2 at usb2
> uhub2: VIA EHCI root hub, rev 2.00/1.00, addr 1
> uhub2: 4 ports with 4 removable, self powered
> 
> Unfortunately, any USB devices I connect don't show up at all.  No
> kernel message, zilch.  It appears they don't even receive any
> power.
> 
> Does USB on alpha work for anybody?

I have no problem with a similar card:
(and I should check this mailbox more often)

[ using 548024 bytes of bsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1982, 1986, 1989, 1991, 1993
	The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2006 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 4.0-current (GENERIC) #1: Tue Nov 21 00:00:51 CET 2006
    janjaap@alf:/mnt/forest/trees/src/sys/arch/alpha/compile/GENERIC
Digital AlphaPC 164SX 533 MHz
8192 byte page size, 1 processor.
total memory = 268435456 (262144K)
(1966080 reserved for PROM, 266469376 used by OpenBSD)
avail memory = 226074624 (220776K)
using 3252 buffers containing 26640384 bytes (26016K) of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), PCA56-2 (unknown minor type 2)
cpu0: Architecture extensions: 1<BWX>
cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 1
cia0: extended capabilities: 1<BWEN>
cia0: using BWX for PCI config and bus access
pci0 at cia0 bus 0
uhci0 at pci0 dev 5 function 0 "VIA VT83C572 USB" rev 0x61: eb164 irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 5 function 1 "VIA VT83C572 USB" rev 0x61: eb164 irq 13
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 5 function 2 "VIA VT6202 USB" rev 0x63: eb164 irq 17
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: VIA EHCI root hub, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
siop0 at pci0 dev 6 function 0 "Symbios Logic 53c875" rev 0x26: eb164 irq 11, using 4K of on-board RAM
scsibus0 at siop0: 16 targets
em0 at pci0 dev 7 function 0 "Intel PRO/1000MT (82541GI)" rev 0x00: eb164 irq 10, address 00:0e:0c:51:3d:a0
sio0 at pci0 dev 8 function 0 "Contaq Microsystems CY82C693U ISA" rev 0x00
pciide0 at pci0 dev 8 function 1 "Contaq Microsystems CY82C693U ISA" rev 0x00: DMA, channel 0 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 6Y160P0>
wd0: 16-sector PIO, LBA48, 156334MB, 320173056 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide1 at pci0 dev 8 function 2 "Contaq Microsystems CY82C693U ISA" rev 0x00: no DMA, channel 0 wired to compatibility
atapiscsi0 at pciide1 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <LITEON, CD-ROM LTN301, MM11> SCSI0 5/cdrom removable
cd0(pciide1:0:0): using PIO mode 4
ohci0 at pci0 dev 8 function 3 "Contaq Microsystems CY82C693U ISA" rev 0x00: couldn't map interrupt
vga0 at pci0 dev 9 function 0 "Matrox MGA G200 PCI" rev 0x01
wsdisplay0 at vga0 mux 1
wsdisplay0: screen 0-5 added (80x25, vt100 emulation)
isa0 at sio0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
wskbd0: connecting to wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x3bc/4 irq 7
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
stray isa irq 3
root on wd0a swap on wd0b
uhub3 at uhub1 port 2
uhub3: ALCOR Generic USB Hub, rev 1.10/3.12, addr 2
uhub3: 4 ports with 4 removable, self powered
rootdev=0x0 rrootdev=0x2400 rawdev=0x2402
stray isa irq 3
wsdisplay0: screen 8 added (80x25, vt100 emulation)
wsdisplay0: screen 9 added (80x25, vt100 emulation)
wsdisplay0: screen 4 deleted
wsdisplay0: screen 5 deleted
wsdisplay0: screen 4 added (80x40, vt100 emulation)
wsdisplay0: screen 5 added (80x40, vt100 emulation)
wsdisplay0: screen 6 added (80x40, vt100 emulation)
wsdisplay0: screen 7 added (80x40, vt100 emulation)
wsdisplay0: screen 10 added (80x50, vt100 emulation)
wsdisplay0: screen 11 added (80x50, vt100 emulation)
umass0 at uhub3 port 4 configuration 1 interface 0
umass0: Generic Mass Storage Device, rev 2.00/1.13, addr 3
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets
sd0 at scsibus2 targ 1 lun 0: <Multi, Flash Reader, 1.00> SCSI0 0/direct removable
sd0: 483MB, 483 cyl, 64 head, 32 sec, 512 bytes/sec, 990976 sec total
umass0: at uhub3 port 4 (addr 3) disconnected
sd0 detached
scsibus2 detached
umass0 detached
ugen0 at uhub3 port 1
ugen0: HTC Generic Serial, rev 2.00/0.90, addr 3