API CS20 alipm(4) error

I just installed OpenBSD/alpha 4.1 on the API Networks CS20 Dual 833  
MHz Alpha machine that arrived this week. On the first bootup with  
GENERIC, I had hundreds of errors stating the following:

alipm0: timeout st 0x0

These kept repeating a few hundred times and then something else in  
the boot process would load and then hundreds more. When logged in  
through ssh I don't see the error but I experience pauses of a second  
or so every few seconds. Using UKC to disable alipm(4) corrects the  
problem but I thought it was worth while to point this error out.  
This is also the case with 4.1-stable. The dmesg follows but with  
alipm(4) disabled. The only thing listed in the dmesg with alipm(4)  
enabled is the above error.

Bryan


Unrecognized boot flag '0'.
[ using 548368 bytes of bsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1982, 1986, 1989, 1991, 1993
	The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2007 OpenBSD. All rights reserved.  http:// 
www.OpenBSD.org

OpenBSD 4.1 (GENERIC) #1028: Sun Mar 11 04:03:15 MDT 2007
     [email protected]:/usr/src/sys/arch/alpha/compile/GENERIC
API CS20D 833 MHz
8192 byte page size, 1 processor.
total memory = 2147483648 (2097152K)
(2924544 reserved for PROM, 2144559104 used by OpenBSD)
avail memory = 1873920000 (1830000K)
using 26178 buffers containing 214450176 bytes (209424K) of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21264B-4 (unknown minor type 4)
cpu0: Architecture extensions: 307<PAT,MVI,CIX,FIX,BWX>
tsc0 at mainbus0: 21272 Chipset, Cchip rev 0
tsc0: 4 Dchips, 1 memory bus of 32 bytes
tsc0: arrays present: 1024MB, 1024MB, 0MB, 0MB, Dchip 0 rev 1
tsp0 at tsc0
pci0 at tsp0 bus 0
siop0 at pci0 dev 3 function 0 "Symbios Logic 53c1010-66" rev 0x01:  
dec 6600 irq 16, using 8K of on-board RAM
scsibus0 at siop0: 16 targets
sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST336706LC, 010A> SCSI3 0/ 
direct fixed
sd0: 35003MB, 26302 cyl, 4 head, 681 sec, 512 bytes/sec, 71687370 sec  
total
fxp0 at pci0 dev 4 function 0 "Intel 8255x" rev 0x08, i82559: dec  
6600 irq 20, address 00:02:56:00:0b:b5
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
sio0 at pci0 dev 7 function 0 "Acer Labs M1533 ISA" rev 0xc3
pciide0 at pci0 dev 16 function 0 "Acer Labs M5229 UDMA IDE" rev  
0xc2: DMA, channel 0 configured to compatibility, channel 1  
configured to compatibility
pciide0: channel 0 disabled (no drives)
atapiscsi0 at pciide0 channel 1 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <SAMSUNG, CD-ROM SN-124, q008> SCSI0 5/ 
cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
"Acer Labs M7101 Power" rev 0x00 at pci0 dev 17 function 0 not  
configured
isa0 at sio0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x3bc/4 irq 7
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
tsp1 at tsc0
pci1 at tsp1 bus 0
fxp1 at pci1 dev 3 function 0 "Intel 8255x" rev 0x08, i82559: dec  
6600 irq 32, address 00:02:56:00:0b:b6
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
"Myricom Myrinet LANai 9.2" rev 0x03 at pci1 dev 4 function 0 not  
configured
stray isa irq 15
stray isa irq 3
root on sd0a swap on sd0b
siop0: target 0 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset  
xfers
rootdev=0x800 rrootdev=0x800 rawdev=0x802
stray isa irq 3
Warning: received processor correctable error.
Warning: received processor correctable error.
Warning: received processor correctable error.
Warning: received processor correctable error.
Warning: received processor correctable error.
Warning: received processor correctable error.