DEC Multia VX40 - missing login on serial port, shutdown strangeness

Hello list,

I recently acquired an old DEC Multia VX40. No floppy, no cdrom, broken
netboot, cpu heatsink works for frying eggs. Installation via
$ dd if=floppy44.fs of=/dev/rsd0c
from another machine worked a treat and now I have a working system.

However, I cannot figure out how to get a login prompt on the serial
port. If I boot the system without keyboard/monitor attached, then the
SRM console appears on the serial port and kernel messages also get
through. In order to do the installation I had to attach a keyboard and
monitor - at the end of the installation I said yes to console on com0.

I've tried adding various lines in /etc/ttys with no avail. I can get
a login on the monitor using ttyC0, but no luck with ttyB0 or tty00.

Now, if I login via the keyboard/monitor, I can type 'halt' and get
back to the SRM console. However reboot and shutdown fail to do either.
They tell me about /etc/rc.shutdown being run and then finishing, but
then hang. A ^C sometimes gets me back to the shell.

With the keyboard unplugged and a serial cable attached, no combination
of halt/reboot/shutdown gets me a power down or SRM console on the
serial port.

Anyone still running OpenBSD on a multia? I see some messages in the
archives regarding PCMCIA - did anyone ever get this going?

-Graham


Unrecognized boot flag '0'.
[ using 589496 bytes of bsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1982, 1986, 1989, 1991, 1993
	The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2008 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 4.4-current (GENERIC) #1457: Tue Sep  9 21:33:12 MDT 2008
   [email protected]:/usr/src/sys/arch/alpha/compile/GENERIC
(PCI ISA), 167MHz
8192 byte page size, 1 processor.
total memory = 33554432 (32768K)
(2351104 reserved for PROM, 31203328 used by OpenBSD)
avail memory = 22716416 (22184K)
mainbus0 at root
cpu0 at mainbus0: ID 0 (primary), LCA-2 (21066 pass 2)
lca0 at mainbus0
pci0 at lca0 bus 0
siop0 at pci0 dev 6 function 0 "Symbios Logic 53c810" rev 0x01: isa irq 11
scsibus0 at siop0: 8 targets, initiator 7
sd0 at scsibus0 targ 3 lun 0: <DEC, RZ26L (C) DEC, 442D> SCSI2 0/direct fixed
sd0: 1001MB, 512 bytes/sec, 2050860 sec total
sio0 at pci0 dev 7 function 0 "Intel 82378IB ISA" rev 0x03
de0 at pci0 dev 8 function 0 "DEC 21040" rev 0x23, DEC 21040 pass 2.3: isa irq 14, address 08:00:2b:e4:32:bf
unknown vendor 0x0047 product 0x0280 (class network subclass miscellaneous, rev 0x47) at pci0 dev 9 function 0 not configured
tga0 at pci0 dev 11 function 0 "DEC 21030" rev 0x02: DC21030 step B, board type T8-02
tga0: 1024 x 768, 8bpp, Bt485 RAMDAC
tga0: interrupting at isa irq 10
wsdisplay0 at tga0 mux 1: console (std, vt100 emulation)
unknown vendor 0x0087 product 0x0280 (class network subclass miscellaneous, rev 0x87) at pci0 dev 12 function 0 not configured
isa0 at sio0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x3bc/4 irq 7
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
stray isa irq 3
stray isa irq 4
softraid0 at root
siop0: target 3 now using tagged 8 bit 10.0 MHz 8 REQ/ACK offset xfers
root on sd0a swap on sd0b dump on sd0b