Re: OpenBSD 7.2 on Alpha

Hey Miod,

Thanks for the offer to look at the logs.

*** BEGIN ***

P00>>>
P00>>>boot dkb0
(boot dkb0.0.0.5.1 -flags A)
=EF=BF=BDblock 0 of dkb0.0.0.5.1 is a valid boot block
reading 15 blocks from dkb0.0.0.5.1
bootstrap code read in
base =3D 200000, image_start =3D 0, image_bytes =3D 1e00
initializing HWRPB at 2000
initializing page table at 1f2000
initializing machine state
setting affinity to the primary CPU
configuring I/O adapters...
  ncr0, hose 1, bus 0, slot 1
  tulip0, hose 1, bus 0, slot 3
  isp0, hose 1, bus 0, slot 5
  floppy0, hose 0, bus 1, slot 0
  ncr1, hose 0, bus 0, slot 4
jumping to bootstrap code

OpenBSD/Alpha Primary Boot
OpenBSD/alpha boot 1.11
VMS PAL rev: 0x4000200010115
OSF PAL rev: 0x4000200020117
Switch to OSF PAL code succeeded.
NOTE: random seed is being reused.
Loading bsd...
8557792+686096 [327418+106+498120+319338]=3D0x9e8958

[ using 1145960 bytes of bsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1982, 1986, 1989, 1991, 1993
=09The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2022 OpenBSD. All rights reserved.  https://www.OpenBSD.=
org

OpenBSD 7.2 (GENERIC) #292: Tue Sep 27 14:50:10 MDT 2022
    [email protected]:/usr/src/sys/arch/alpha/compile/GENERIC
AlphaServer 4X00 5/300 2MB, 299MHz
8192 byte page size, 2 processors.
real mem =3D 1073741824 (1024MB)
rsvd mem =3D 2121728 (2MB)
avail mem =3D 1044185088 (995MB)
random: boothowto does not indicate good seed
mainbus0 at root
cpu0 at mainbus0: ID 0 (primary), 21164-5 (pass 4)
cpu at mainbus0 not configured
mcbus0 at mainbus0: 2MB BCache
mcmem0 at mcbus0 mid 1: Memory
mcpcia0 at mcbus0 mid 5: PCI Bridge
mcpcia0: Horse rev 3, left handed Saddle rev 2, CAP rev 2
pci0 at mcpcia0 bus 0
siop0 at pci0 dev 1 function 0 "Symbios Logic 53c810" rev 0x02: kn300 irq 3=
6
scsibus0 at siop0: 8 targets, initiator 7
cd0 at scsibus0 targ 5 lun 0: <DEC, RRD45 (C) DEC, 1645> removable
dc0 at pci0 dev 3 function 0 "DEC 21142/3" rev 0x30: kn300 irq 44, address =
00:00:f8:06:7a:59
dcphy0 at dc0 phy 31: internal PHY
qlw0 at pci0 dev 5 function 0 "QLogic ISP1020" rev 0x05: kn300 irq 52
qlw0: firmware rev 4.66.0, attrs 0x0
scsibus1 at qlw0: 16 targets, initiator 7
sd0 at scsibus1 targ 0 lun 0: <DEC, RZ1DB-CS (C) DEC, 0307> serial.DEC_RZ1D=
B-CS_(C)_DECLAS03857
sd0: 8678MB, 512 bytes/sector, 17773524 sectors
mcpcia1 at mcbus0 mid 4: PCI Bridge
mcpcia1: Horse rev 3, left handed Saddle rev 2, CAP rev 2
pci1 at mcpcia1 bus 0
pceb0 at pci1 dev 1 function 0 "Intel 82375EB EISA" rev 0x05
siop1 at pci1 dev 4 function 0 "Symbios Logic 53c810" rev 0x02: kn300 irq 1=
6
scsibus2 at siop1: 8 targets, initiator 7
vga0 at pci1 dev 5 function 0 "S3 Trio32/64" rev 0x00
wsdisplay0 at vga0 mux 1
wsdisplay0: screen 0-5 added (80x25, vt100 emulation)
eisa0 at pceb0: DEC6400, 3 slots
isa0 at pceb0
isadma0 at isa0
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x3bc/4 irq 7
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
stray kn300 irq 16
stray kn300 irq 36
stray isa irq 3
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
scsibus4 at softraid0: 256 targets

fatal kernel trap:

    trap entry =3D 0x3 (instruction fault)
    a0         =3D 0x4
    a1         =3D 0x0
    a2         =3D 0x2
    pc         =3D 0xfffffc000060dbec
    ra         =3D 0xfffffc000060dbcc
    curproc    =3D 0xfffffc0000e05f80
        pid =3D 0, comm =3D swapper

panic: trap
Stopped at      db_enter+0x8:   lda     sp,10(sp)
    TID    PID    UID     PRFLAGS     PFLAGS  CPU  COMMAND
db_enter(0, 7ffffe7cc0003f8, 1, 8, 3, 8) at db_enter+0x8
panic(?, fffffc0000d78c90, 1, 8, 3, 8) at panic+0xe8
trap(?, ?, ?, ?, ?, 8) at trap+0x108
XentIF(?, ?, ?, ?, ?, 8) at XentIF+0x20
__bwx_switch0(216a000, 0, 2, fffffc0000cd5938, 0, 0) at __bwx_switch0+0x8
cpu_switchto(?, 0, 2, fffffc0000cd5938, 0, 0) at cpu_switchto+0x68
https://www.openbsd.org/ddb.html describes the minimum info required in bug
reports.  Insufficient info makes it difficult to find and fix bugs.
ddb>

*** END ***

----- Original Message -----
From: "Miod Vallat" <[email protected]>
To: "Mark Butt" <[email protected]>
Cc: "alpha" <[email protected]>
Sent: Monday, January 2, 2023 12:44:10 PM
Subject: Re: OpenBSD 7.2 on Alpha

> It's a serial console.  Yes,  I can provide a boot log.  Do you just want=
 a capture of the text to the screen during the boot process or is there a =
particular command(s) that I should run at ddb?

At this point, I would like the complete boot log up to the ddb prompt;
I have nothing else to suggest yet.