bsd.rd boots with corrupted memory on Juniper Networks SRX300

bugs@,

I'd like to share that little that I do have for now with attempt to boot
bsd.rd from todays snapshot at Juniper Networks SRX300 which smeels like a
corrupted memory:

SPI stage 1 bootloader (Build time: May  3 2016 - 23:48:30)
early_board_init: Board type: SRX_300

U-Boot 2013.07-JNPR-3.1 (Build time: May 03 2016 - 23:48:31)

SRX_300 board revision major:1, minor:8, serial #: CV3519AF0028
OCTEON CN7020-AAP pass 1.2, Core clock: 1200 MHz, IO clock: 600 MHz, DDR clock: 667 MHz (1334 Mhz DDR)
Base DRAM address used by u-boot: 0x10fc00000, size: 0x400000
DRAM: 4 GiB
Clearing DRAM...... done
Using default environment

SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
Found valid SPI bootloader at offset: 0x90000, size: 1481840 bytes


U-Boot 2013.07-JNPR-3.1 (Build time: May 03 2016 - 23:50:19)

Using DRAM size from environment: 4096 MBytes
checkboard siege 
SATA0: not available
SATA1: not available
SATA BIST STATUS = 0x0
SRX_300 board revision major:1, minor:8, serial #: CV3519AF0028
OCTEON CN7020-AAP pass 1.2, Core clock: 1200 MHz, IO clock: 600 MHz, DDR clock: 667 MHz (1334 Mhz DDR)
Base DRAM address used by u-boot: 0x10f000000, size: 0x1000000
DRAM: 4 GiB
Clearing DRAM...... done
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
PCIe: Port 0 link active, 1 lanes, speed gen2
PCIe: Link timeout on port 1, probably the slot is empty
PCIe: Port 2 not in PCIe mode, skipping
Net:   octeth0
Interface 0 has 1 ports (SGMII)
Type the command 'usb start' to scan for USB storage devices.

Boot Media: eUSB usb 
Found TPM SLB9660 TT 1.2 by Infineon
TPM initialized
Hit any key to stop autoboot:  0 
Octeon srx_300_ram# dhcp
BCM MDK initializing ...
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
BCM MDK init done.
BOOTP broadcast 1
octeth0: Up 1000 Mbps Full duplex (port  0) (SGMII)
BOOTP broadcast 2
DHCP client bound to address 172.31.3.27
Octeon srx_300_ram# setenv serverip 172.31.2.77
Octeon srx_300_ram# tftpboot 0 bsd.rd
Using octeth0 device
TFTP from server 172.31.2.77; our IP address is 172.31.3.27; sending through gateway 172.31.3.1
Filename 'bsd.rd'.
Load address: 0x20000000
Loading: *
TFTP server died; starting again
Using octeth0 device
TFTP from server 172.31.2.77; our IP address is 172.31.3.27; sending through gateway 172.31.3.1
Filename 'bsd.rd'.
Load address: 0x20000000
Loading: ##################################################
         47.9 KiB/s
done
Bytes transferred = 8877361 (877531 hex)
Octeon srx_300_ram# bootoctlinux
Allocating memory for ELF segment: addr: 0xffffffff81000000 (adjusted to: 0x1000000), size 0x8780e0
## Loading big-endian Linux kernel with entry point: 0xffffffff81000000 ...
Bootloader: Done loading app on coremask: 0x1
Starting cores:
 0x1
bootmem desc 0x6c108 version 3.0
avail phys mem 0x0000000000100300 - 0x0000000000fffc20
avail phys mem 0x00000000018780e0 - 0x000000000f100000
avail phys mem 0x000000000f100010 - 0x000000000f101908
avail phys mem 0x000000000f101910 - 0x000000000fffdc00
avail phys mem 0x0000000020000000 - 0x000000010f000000
Total DRAM Size 0x0000000100000000
mem_layout[0] page 0x0000000000000041 -> 0x00000000000003FF
mem_layout[1] page 0x000000000000061F -> 0x0000000000003C40
owa�¿9D�NcJƣ)¤qΥv85�L���pq¥%=�J9���R2K!�k�zjw���c�®j!)�rb����[JH���c�=�݅��c�=�݅��c�=�݅��c�=��d�#�����k������o�����k���'o����'g
                                                                                                  b¦BJo����Rk�
                                                                                                              �C���/B�O�!�bMG�½=�¬!�z�s3w!�nj3�w!���77_)����>q���R������z¦s�s�������!�


-- 
wbr, Kirill