Re: HP9000 K-Series support

Making, drinking tea and reading an opus magnum from Hellmuth Michaelis:
> Fyi, i've setup OpenBSD-current on a 715/64 (after trying unsuccessfully
> to get build cross tools on i386, probably my fault ..) and have the K
> remote booted from that machine.
> 
> After quite some time hacking the source, reading the fine PDC manual
> and studying the debian-parisc source, today i got the K220 booted to
> the point where it asks for installing or go to a shell.

you care to share the diffs maybe?

> Now i need a driver for the built in Fast-Wide-Diff SCSI bus .. ;-)

i must be blind and do not see fwd in your dmesg?

cu

> lasi0 at mainbus0 offset fd00000 irq 86btlb_insert(2): 0:ffd00=ffd00[80,1080002]
> : rev 3.0
> gsc0 at lasi0
> "LASI Bus Adapter" at gsc0 (type b, sv 81, hv 50) offset 0 not configured
> osiop0 at gsc0 offset 6000 irq 86: NCR53C710 rev 2, 40MHz, SCSI ID 7
> scsibus0 at osiop0: 8 targets
> osiop0: target 0 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
> st0 at scsibus0 targ 0 lun 0: <HP, C1533A, 9608> SCSI2 1/sequential removable
> st0: drive empty
> osiop0: target 2 now using 8 bit 4 MHz 8 REQ/ACK offset xfers
> cd0 at scsibus0 targ 2 lun 0: <TOSHIBA, CD-ROM XM-5401TA, 1036> SCSI2 5/cdrom removable
> ie0 at gsc0 offset 7000 irq 87: LASI/i82596CA v1.0, address 08:00:09:d4:36:b8
> lpt0 at gsc0 offset 2000 irq 88
> "PS/2 port" at gsc0 (type a, sv 84, hv 50) offset 8000 not configured
> "PS/2 port" at gsc0 (type a, sv 84, hv 50) offset 8100 not configured
> "NCR 53C710 SCSI" at mainbus0 (type a, sv 82, hv 50) offset fd06000 not configured
> "Core LAN" at mainbus0 (type a, sv 8a, hv 50) offset fd07000 not configured
> "Core Centronics" at mainbus0 (type a, sv 74, hv 50) offset fd02000 not configured
> "PS/2 port" at mainbus0 (type a, sv 84, hv 50) offset fd08000 not configured
> "PS/2 port" at mainbus0 (type a, sv 84, hv 50) offset fd08100 not configured
> "BC Runway Port" at mainbus0 (type c, sv b, hv 7) offset ff88000 not configured
> "BC Runway Port" at mainbus0 (type c, sv b, hv 7) offset ff8a000 not configured
> cpu0 at mainbus0 offset ffa0000 irq 31: PCXT' L1-B 120MHz, FPU PCXT' (Tornado) rev 1
> cpu0: 1024K(32b/l) Icache, 1026K(32b/l) wr-back coherent Dcache, 120 coherent TLB, 16 BTLB
> "PA-RISC" at mainbus0 (type 0, sv 4, hv c0) offset ffa2000 not configured
> mem0 at mainbus0 offset ffb1000: size 1024MB

did you reverse the device probe in your changes for some particular reason ?
also why does it list same device multiple times?

cu

-- 
    paranoic mickey       (my employers have changed but, the name has remained)