712/80 console errors

Hello!
I successfully installed the latest snapshot on a 712/80 HP-machine.
However i see  

SPID bits: 0x0, error = -2                                          
WARNING: PDC_COPROC error -3
0x00.CEC0                   

early in the boot-process.

Later on, on disk-activity, there are lots of:
Aug 18 13:41:57 hpux /bsd: ie0: receive descriptors out of sync at 37
Aug 18 13:42:02 hpux /bsd: ie0: receive descriptors out of sync at 69
Aug 18 13:42:07 hpux /bsd: ie0: receive descriptors out of sync at 76
Aug 18 13:42:21 hpux /bsd: ie0: receive descriptors out of sync at 44
Aug 18 13:42:24 hpux /bsd: ie0: receive descriptors out of sync at 34
Aug 18 13:42:24 hpux /bsd: ie0: receive descriptors out of sync at 70
Aug 18 13:42:36 hpux /bsd: ie0: receive descriptors out of sync at 70
Aug 18 13:42:39 hpux /bsd: ie0: receive descriptors out of sync at 63
Aug 18 13:42:41 hpux /bsd: ie0: receive descriptors out of sync at 67
Aug 18 13:42:41 hpux /bsd: ie0: receive descriptors out of sync at 69

From looking at  /usr/src/sys/dev/isa/if_ie.c, this does not look too
dangerous. If this safely can be ingnored, i will comment them out.
Comments?

Alf

dmesg:
[ using 277900 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
	The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2004 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 3.6-beta (GENERIC) #152: Mon Aug 16 14:37:34 MDT 2004
    [email protected]:/usr/src/sys/arch/hppa/compile/GENERIC
HP 9000/712/80 (King Gecko) PA-RISC 1.1c
real mem = 67108864 (524288 reserved for PROM, 4997120 used by OpenBSD)
avail mem = 53260288
using 1630 buffers containing 6676480 bytes of memory
mainbus0 (root) [flex fff80000]
pdc0 at mainbus0
power0 at mainbus0: DR25
mem0 at mainbus0 offset ffbf000: viper rev 0, size 64MB
cpu0 at mainbus0 offset ffbe000 irq 31: PCXL L1-A 80MHz, FPU PCXL (CMOS-26B) rev 1
cpu0: 128K(32b/l) Icache, 128K(32b/l) wr-back coherent Dcache, 64 coherent TLB, 8 BTLB
lasi0 at mainbus0 offset 100000 irq 28: rev 3.0
gsc0 at lasi0
gsckbc0 at gsc0 offset 8100 irq 26
gsckbc1 at gsc0 offset 8000 irq 26
"floppy controller" at gsc0 (type a, sv 83, hv c0) offset a000 not configured
harmony0 at gsc0 offset 4000 irq 13: rev 18
audio0 at harmony0
lpt0 at gsc0 offset 2000 irq 7
com0 at gsc0 offset 5000 irq 5: ns16550a, 16 byte fifo
com0: console
ie0 at gsc0 offset 7000 irq 8: LASI/i82596CA v1.0, address 08:00:09:7d:0a:e2
osiop0 at gsc0 offset 6000 irq 9: NCR53C710 rev 2, 40MHz, SCSI ID 7
scsibus0 at osiop0: 8 targets
osiop0: target 6 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
sd0 at scsibus0 targ 6 lun 0: <HP, C3325A, HP08> SCSI2 0/direct fixed
sd0: 2048MB, 3703 cyl, 9 head, 125 sec, 512 bytes/sec, 4194685 sec total
sti0 at mainbus0 offset 8000000 irq 11: HPA208LC640 rev 8.04;7, ID 0x2B4DED6D40A00499
sti0: 2048x1024 frame buffer, 640x480x8 display, offset 0x0
sti0: 8x16 font type 1, 16 bpc, charset 0-255
biomask 0x7 netmask 0xf ttymask 0x3f
boot path: 2/0/1.6 class=1 flags=0 hpa=0xf0106000 spa=0x0 io=0x84ec
root on sd0a swap on sd0b
wsdisplay0 at sti0
wsdisplay0: screen 0 added (default, vt100 emulation)
rootdev=0x400 rrootdev=0xa00 rawdev=0xa02