Quad Ethernet card causing crash.

Hi.

I got a quad Ethernet card to play with. Unfortunately OpenBSD crashes
while booting, see below. Any ideas?

>> OpenBSD/hppa BOOT 0.8
booting dk4a:/bsd: 2864588+40960+409600 [52+133584+113603]=0x42a73c
SPID bits: 0x0, error = -2
WARNING: PDC_COPROC error -3
[ using 247612 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2004 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 3.5 (B180L) #4: Wed Jul 21 18:58:11 CEST 2004
    [email protected]:/usr/tmp/B180L
HP 9000/778/B180L+ (Merlin L2+ 180) PA-RISC 1.1e
real mem = 536870912 (524288 reserved for PROM, 6152192 used by OpenBSD)
avail mem = 463732736
using 8421 buffers containing 53657600 bytes of memory
mainbus0 (root) [flex fff80000]
pdc0 at mainbus0
power0 at mainbus0 offset 140000
mem0 at mainbus0 offset ffbf000: size 512MB, 1MB L2 cache
cpu0 at mainbus0 offset ffbe000 irq 31: PCXL2 L1-A 180MHz, FPU VR rev 1
cpu0: 64K(32b/l) Icache, 64K(32b/l) wr-back coherent Dcache, 96 coherent TLB, 8 
BTLB
phantomas0 at mainbus0 offset fc00000
sti0 at phantomas0 offset 8000000 irq 11: INTERNAL_EG_1280 rev 8.07;9, ID 0x2D08
C0A709A02587
sti0: 2048x2048 frame buffer, 1280x1024x8 display, offset 0x0
sti0: 8x16 font type 1, 16 bpc, charset 0-255
"WAX Bus Adapter" at phantomas0 (type b, sv 8e, hv a0) offset fe00000 not config
ured
lasi0 at phantomas0 offset fd00000 irq 28: rev 3.0
gsc0 at lasi0: wordleds
"floppy controller" at gsc0 (type a, sv 83, hv f0) offset a000 not configured
gsckbc0 at gsc0 offset 8100 irq 26
gsckbc1 at gsc0 offset 8000 irq 26
gsckbd0 at gsckbc1
wskbd0 at gsckbd0 mux 1
osiop0 at gsc0 offset 6000 irq 9: NCR53C710 rev 2, 40MHz, SCSI ID 7
scsibus0 at osiop0: 8 targets
com0 at gsc0 offset 5000 irq 5: ns16550a, 16 byte fifo
com0: console
harmony0 at gsc0 offset 4000 irq 13: rev 0
audio0 at harmony0
lpt0 at gsc0 offset 2000 irq 7
dino0 at phantomas0 offset ff80000 irq 26: Dino V3.1
pci0 at dino0
"3Com 3c905 100Base-TX" rev 0x00 at pci0 dev 1 function 0 not configured
ppb0 at pci0 dev 2 function 0 "DEC 21152 PCI-PCI" rev 0x03
pci1 at ppb0 bus 1
dc0 at pci1 dev 4 function 0 "DEC 21140" rev 0x22: irq 3, address 00:00:bc:11:d6
:10
dcphy0 at dc0 phy 31: internal PHY
dc1 at pci1 dev 5 function 0 "DEC 21140" rev 0x22: irq 4, address 00:00:bc:11:d6
:11
dcphy1 at dc1 phy 31: internal PHY
dc2 at pci1 dev 6 function 0 "DEC 21140" rev 0x22: irq 1,: can't create tx map
panic: config_make_softc: allocation for device softc failed
Stopped at      Debugger+0x18:  break   0,5
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb> t
Debugger(2e2720,ffd05800,5,469000) at Debugger+0x18
panic(2e1174,2,1,2a6cfc) at panic+0xf8
panic(2e1140,c0b00014,c08eda14,c0b00014) at panic+0xdc
config_make_softc(4b2e48,407e2c,2a8664,407e14) at config_make_softc+0xa0
config_attach(30fdec,c08eda00,4b2e48,469000) at config_attach+0x6c
config_found_sm(2e1140,c08eda14,c08eda54,c08eda14) at config_found_sm+0x64
pciattach(4b2c88,407e70,2a6cfc,407e58) at pciattach+0x260
config_attach(31af34,c08eda40,4b2c88,469000) at config_attach+0x1ec
config_found_sm(2e1140,c08eda54,c08eda94,7ac0) at config_found_sm+0x64
ppbattach(2e10e4,ffd05800,5,469000) at ppbattach+0xe8
config_attach(30fdec,c08eda80,4b2ac8,469000) at config_attach+0x1ec
config_found_sm(2e1140,c08eda94,c08f8c14,7a70) at config_found_sm+0x64
pciattach(0,0,0,0) at pciattach+0x260
config_attach(31c6a0,31c688,3,1) at config_attach+0x1ec
config_found_sm(2e1140,c08f8c14,c08edf14,79e0) at config_found_sm+0x64
dinoattach(2e10e4,ffd05800,5,469000) at dinoattach+0x58c
config_attach(4b2758,30,46d000,4b2488) at config_attach+0x1ec
config_found_sm(31c1ac,c08edf00,4b2488,469000) at config_found_sm+0x64
pdc_scanbus(2e1140,c08edf14,c08edfd4,250) at pdc_scanbus+0x44c
phantomasattach(4b2308,408054,2ad6d0,40803c) at phantomasattach+0x8c
config_attach(31bf44,c08eef00,4b2308,469000) at config_attach+0x1ec
config_found_sm(31be08,fff80000,4686f0,fffffff7) at config_found_sm+0x64
pdc_scanbus(2e1134,c08edfd4,50,40) at pdc_scanbus+0x44c
mbattach(78d800,7894a8,78d800,78f138) at mbattach+0x280
config_attach(0,44cb70,50,44cb70) at config_attach+0x1ec
config_rootfound(2deb74,2deab4,2,7) at config_rootfound+0x80
cpu_configure(0,0,0,0) at cpu_configure+0x50
main(0,0,0,0) at main+0x46c
-- trap #0
$callmain+0x8:
ddb> ps
   PID   PPID   PGRP    UID  S       FLAGS  WAIT       COMMAND
*    0     -1      0      0  2     0x80204             swapper
ddb> 
-- 


tschüß,
       Jochen

Homepage: http://www.unixag-kl.fh-kl.de/~jkunz/