Re: 715/100 Installation (snapshot 20th OCT).

New snapshot (20/10/04) does not panic at boot - install goes great:

[ using 278184 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
 	The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2004 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 3.6-current (GENERIC) #176: Tue Oct 19 10:48:19 MDT 2004
     [email protected]:/usr/src/sys/arch/hppa/compile/GENERIC
HP 9000/715/100 (Mirage Sr.) PA-RISC 1.1c
real mem = 67108864 (524288 reserved for PROM, 5201920 used by OpenBSD)
avail mem = 53043200
using 1630 buffers containing 6676480 bytes of memory
mainbus0 (root) [flex fff80000]
pdc0 at mainbus0
power0 at mainbus0: not available
mem0 at mainbus0 offset ffbf000: viper rev 0, size 64MB
cpu0 at mainbus0 offset ffbe000 irq 31: PCXL L1-A 100MHz, FPU PCXL (CMOS-26B) rev 1
cpu0: 128K(32b/l) Icache, 128K(32b/l) wr-back coherent Dcache, 120 coherent TLB, 8 BTLB
wax0 at mainbus0 offset 200000 irq 24
gsc2 at wax0
com1 at gsc2 offset 2000 irq 6: ns16550a, 16 byte fifo
hil0 at gsc2 offset 1000 irq 1
lasi0 at mainbus0 offset 100000 irq 28: rev 3.0
gsc0 at lasi0: wordleds
gsckbc0 at gsc0 offset 8100 irq 26
gsckbc1 at gsc0 offset 8000 irq 26
"floppy controller" at gsc0 (type a sv 83 mod 2 hv 90) offset a000 not configured
harmony0 at gsc0 offset 4000 irq 13: rev 0
audio0 at harmony0
lpt0 at gsc0 offset 2000 irq 7
com0 at gsc0 offset 5000 irq 5: ns16550a, 16 byte fifo
com0: console
ie0 at gsc0 offset 7000 irq 8: LASI/i82596CA v2.0, address 08:00:09:a7:ba:52
osiop0 at gsc0 offset 6000 irq 9: NCR53C710 rev 2, 40MHz, SCSI ID 7
scsibus0 at osiop0: 8 targets
osiop0: target 3 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
sd0 at scsibus0 targ 3 lun 0: <SEAGATE, ST31200N SUN1.05, 9460> SCSI2 0/direct fixed
sd0: 1006MB, 2700 cyl, 9 head, 84 sec, 512 bytes/sec, 2061108 sec total
osiop0: target 4 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
sd1 at scsibus0 targ 4 lun 0: <SEAGATE, ST32430N, HP04> SCSI2 0/direct fixed
sd1: 2048MB, 3992 cyl, 9 head, 116 sec, 512 bytes/sec, 4194685 sec total
sti0 at mainbus0 offset 8000000 irq 11: HPA208LC800 rev 8.04;7, ID 0x2B4DED6D40A00499
sti0: 2048x1024 frame buffer, 800x600x8 display, offset 0x0
sti0: 8x16 font type 1, 16 bpc, charset 0-255
biomask 0x7 netmask 0xf ttymask 0x3f
boot path: 2/0/1.3 class=1 flags=c0<autoboot,autosearch> hpa=0xf0106000 spa=0x0 io=0x84e8
root on sd0a swap on sd0b
hil0: no devices
wsdisplay0 at sti0
wsdisplay0: screen 0 added (default, vt100 emulation)
rootdev=0x400 rrootdev=0xa00 rawdev=0xa02


Thanks Michael.

Do you get this error msg sometimes:

sd0(osiop0:3:0): Check Condition (error 0x70) on opcode 0x0
     SENSE KEY: Not Ready
      ASC/ASCQ: Logical Unit Not Ready, Initialization Command Required
      FRU CODE: 0x1

I see this every now and then.  Just the disks warming up?

Otherwise, the machine is *very* reliable.

Best regards,

STUART

--