Re: HP 9000 K200 (819) ... Headway made!!!

> Date: Wed, 19 Dec 2007 11:55:41 -0500 (EST)
> From: Rob Sciuk <[email protected]>
>
> SPID bits: 0x0, error = -2
> pdc_coproc: 0xc0, 0xc0; model b rev 1
> [ bsd ELF symbol table not valid: symtab unaligned ]
> [ no symbol table formats found ]
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>  	The Regents of the University of California.  All rights reserved.
> Copyright (c) 1995-2007 OpenBSD. All rights reserved.  http://www.OpenBSD.org
> 
> OpenBSD 4.2-current (RAMDISK) #561: Tue Dec 18 19:31:16 MST 2007
>      [email protected]:/usr/src/sys/arch/hppa/compile/RAMDISK
> HP 9000/819/K200 (KittyHawk DC2 100) PA-RISC 1.1a
> real mem = 536870912 (524288 reserved for PROM, 8269824 used by OpenBSD)
> avail mem = 517582848
> mainbus0 at root [flex fff80000]
> pdc0 at mainbus0
> power0 at mainbus0: not available
> mem0 at mainbus0 offset ffb1000: size 512MB
> cpu0 at mainbus0 offset ffa2000 irq 31: PCXT' L1-B 100MHz, FPU PCXT' (Tornado) rev 1
> cpu0: 256K(32b/l) Icache, 258K(32b/l) wr-back Dcache, 120 coherent TLB, 16 BTLB
> "PA-RISC" at mainbus0 (type 0 sv 4 mod 58 hv b0) offset ffa0000 not configured
> uturn0 at mainbus0 offset ff8a000: U2 rev 7
> lasi0 at uturn0 offset fd00000 irq 28: rev 3.0
> gsc0 at lasi0: wordleds
> gsckbc0 at gsc0 offset 8100 irq 26
> gsckbc1 at gsc0 offset 8000 irq 26
> ie0 at gsc0 offset 7000 irq 8: LASI/i82596CA v1.0, address 08:00:09:f0:3a:a2
> osiop0 at gsc0 offset 6000 irq 9: NCR53C710 rev 2, 40MHz, SCSI ID 7
> scsibus0 at osiop0: 8 targets
> osiop0: target 0 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
> st0 at scsibus0 targ 0 lun 0: <HP, C1533A, AN04> SCSI2 1/sequential removable
> osiop0: target 2 now using 8 bit 4 MHz 8 REQ/ACK offset xfers
> cd0 at scsibus0 targ 2 lun 0: <TOSHIBA, CD-ROM XM-5401TA, 3115> SCSI2 5/cdrom removable
> lpt0 at gsc0 offset 2000 irq 7
> uturn1 at mainbus0 offset ff88000: U2 rev 7
> biomask 0xb netmask 0x2b ttymask 0x3f
> bootpath: 10/12/6.10000.fa520040.f45e1a89.9ad5fe03.c0a8450b.c0a84558 class=4098 flags=0 hpa=0xffd07000 spa=0x0 io=0xc000
> rd0: fixed, 5120 blocks
> root on rd0a swap on rd0b dump on rd0b

Cool!  But it doesn't find all devices yet.  Could you try a verbose
boot with this kernel?