Re: HP 9000 K200 (819) ... Headway made!!!

On Thu, 20 Dec 2007, Mark Kettenis wrote:

> Anyway, you can find a new kernel at
>
>  http://www.jive.nl/~kettenis/bsd.lif
>
> Hopefully this one will make it see your disks.

Nope:  Another panic ... 8-{


Firmware Version  2.9

Duplex Console IO Dependent Code (IODC) revision 4

------------------------------------------------------------------------------
    (c) Copyright 1990-1998, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

   Processor   Speed            State           CoProcessor State  Cache Size
   ---------  --------   ---------------------  -----------------  ----------

       0      100  MHz   Active                 Functional          256 KB
       1      100  MHz   Idle                   Functional          256 KB

   Central Bus Speed (in MHz)  :        100
   Available Memory (bytes)    :  536870912
   Good Memory Required (bytes):   19648512


    Primary boot path:    10/0.6   (dec)
    Alternate boot path:  10/12/5.2   (dec)
    Console path:         10/4/0.0   (dec)
    Keyboard path:        10/12/7.0   (dec)


Processor is starting autoboot process.

To discontinue, press any key within 10 seconds.

Boot terminated.


------- Main Menu -------------------------------------------------------------

         Command                         Description
         -------                         -----------

         BOot [PRI|ALT|<path>]           Boot from specified path
         PAth [PRI|ALT] [<path>]         Display or modify a path
         SEArch [DIsplay|IPL] [<path>]   Search for boot devices

         COnfiguration menu              Displays or sets boot values
         INformation menu                Displays hardware information
         SERvice menu                    Displays service commands

         DIsplay                         Redisplay the current menu
         HElp [<menu>|<command>]         Display help for menu or command
         RESET                           Restart the system
-------
Main Menu: Enter command or menu > boot 10/12/6.0
Interact with IPL (Y or N)?> y

Booting... 
Network Station Address 080009-f03aa2

Boot IO Dependent Code (IODC) revision 2


HARD Booted.

>> OpenBSD/hppa BOOT 0.8
|/-\|/-\|boot> 
booting lf0a:/bsd: /-\|/-\|/-\|/-\|/-\|3600384/-\|+696320/-\|+69632/-\|+434176/- [52\|+175008/-\|+157322/-\|]=0x4f63d4
SPID bits: 0x0, error = -2
pdc_coproc: 0xc0, 0xc0; model b rev 1
[ using 332756 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
 	The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2007 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 4.2-current (GENERIC) #37: Thu Dec 20 12:44:37 CET 2007
     [email protected]:/usr/src/sys/arch/hppa/compile/GENERIC
HP 9000/819/K200 (KittyHawk DC2 100) PA-RISC 1.1a
real mem = 536870912 (524288 reserved for PROM, 6266880 used by OpenBSD)
avail mem = 519585792
mainbus0 at root [flex fff80000]
pdc0 at mainbus0
power0 at mainbus0: not available
mem0 at mainbus0 offset ffb1000: size 512MB
cpu0 at mainbus0 offset ffa2000 irq 31: PCXT' L1-B 100MHz, FPU PCXT' (Tornado) rev 1
cpu0: 256K(32b/l) Icache, 258K(32b/l) wr-back Dcache, 120 coherent TLB, 16 BTLB
"PA-RISC" at mainbus0 (type 0 sv 4 mod 58 hv b0) offset ffa0000 not configured
uturn0 at mainbus0 offset ff8a000: U2 rev 7
lasi0 at uturn0 offset fd00000 irq 28: rev 3.0
gsc0 at lasi0: wordleds
gsckbc0 at gsc0 offset 8100 irq 26
gsckbc1 at gsc0 offset 8000 irq 26
lpt0 at gsc0 offset 2000 irq 7
ie0 at gsc0 offset 7000 irq 8: LASI/i82596CA v1.0, address 08:00:09:f0:3a:a2
osiop0 at gsc0 offset 6000 irq 9: NCR53C710 rev 2, 40MHz, SCSI ID 7
scsibus0 at osiop0: 8 targets
osiop0: target 0 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
st0 at scsibus0 targ 0 lun 0: <HP, C1533A, AN04> SCSI2 1/sequential removable
osiop0: target 2 now using 8 bit 4 MHz 8 REQ/ACK offset xfers
cd0 at scsibus0 targ 2 lun 0: <TOSHIBA, CD-ROM XM-5401TA, 3115> SCSI2 5/cdrom removable
uturn1 at mainbus0 offset ff88000: U2 rev 7
biomask 0x7 netmask 0xf ttymask 0x3f
bootpath: 10/12/6.10000.f48c0040.f45e1a89.50c1fe03.c0a8450b.c0a84558 class=4098 flags=0 hpa=0xffd07000 spa=0x0 io=0xc000
softraid0 at root
nfs_boot: using interface ie0, with revarp & bootparams
panic: revarp failed, error=51
Stopped at      Debugger+0x18:  break   0,5
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb> trace
Debugger(417d78,4aee14,0,3a8) at Debugger+0x18
panic(42daf8,33,f551027,0) at panic+0x104
panic(4bb000,c08fa800,4ac90c,0) at panic+0xdc
nfs_boot_init(0,4d,f0140000,506000) at nfs_boot_init+0x2e8
nfs_mountroot(413a44,413984,0,506000) at nfs_mountroot+0x84
vfs_mountroot(6d1c5bdc,36b57747,9b5abba3,cdad5dd1) at vfs_mountroot+0x2c
main(0,0,0,0) at main+0x7b8
-- trap #0
$start+0x154:
ddb> ps
    PID   PPID   PGRP    UID  S       FLAGS  WAIT          COMMAND
      4      0      0      0  2    0x100600                pfpurge
      3      0      0      0  3    0x100200  bored         syswq
      2      0      0      0  3    0x100200                idle0
      1      0      0      0  3           0  initexec      swapper
*    0     -1      0      0  7     0x80200                swapper
ddb> ~[scanner].Connected.
Connected.

Disconnected.