Re: HP 9000 K200 (819) ... Headway made!!!
[email protected] (Eric Schnoebelen) Thu, 20 Dec 2007 17:01:32 -0600
| Newsgroups | gmane.os.openbsd.hppa |
|---|---|
| Message-ID | <[email protected]> |
Rob Sciuk writes: - On Thu, 20 Dec 2007, Mark Kettenis wrote: - - >>> ``ioscan -f'' would provide useful information about the disks - >>> that are attached. - >> - >> I will do. The HPUX boot currently takes about 30-50 min owing to - >> a misconfigured network ... so it'll be about an hour to get you the - >> ioscan -f stand by. - - Here's the whole ball of wax ... and yes, it took this long 8-/ Oh, I'm not surprised.. a K200 is slow (by modern standards) and HP-UX 11.00 is BIG! :D - Firmware Version 2.9 - - Duplex Console IO Dependent Code (IODC) revision 4 - - --------------------------------------------------------------------------- - (c) Copyright 1990-1998, Hewlett-Packard Company, All rights reserved - --------------------------------------------------------------------------- - - Processor Speed State CoProcessor State Cache Size - --------- -------- --------------------- ----------------- ---------- - 0 100 MHz Active Functional 256 KB - 1 100 MHz Idle Functional 256 KB - - Central Bus Speed (in MHz) : 100 - Available Memory (bytes) : 536870912 - Good Memory Required (bytes): 19648512 - - - Primary boot path: 10/0.6 (dec) - Alternate boot path: 10/12/5.2 (dec) - Console path: 10/4/0.0 (dec) - Keyboard path: 10/12/7.0 (dec) - - - Processor is starting autoboot process. - - To discontinue, press any key within 10 seconds. - - 10 seconds expired. - Proceeding... - - Trying Primary Boot Path - ------------------------ - - Booting... - Boot IO Dependent Code (IODC) revision 152 - - - HARD Booted. - - ISL Revision A.00.38 OCT 26, 1994 - - ISL booting hpux - - Boot - : disc(10/0.6.0;0)/stand/vmunix [...] [ioscan reformatted slightly for redability.] - # ioscan -f - Class I H/W Path Driver S/W State H/W Type Description - ======================================================================== - bc 0 root CLAIMED BUS_NEXUS - bc 1 8 ccio CLAIMED BUS_NEXUS I/O Adapter - bc 2 10 ccio CLAIMED BUS_NEXUS I/O Adapter - ext_bus 0 10/0 c720 CLAIMED INTERFACE GSC built-in - Fast/Wide SCSI - Interface - target 0 10/0.3 tgt CLAIMED DEVICE - disk 0 10/0.3.0 sdisk CLAIMED DEVICE SEAGATE ST15150W - target 1 10/0.4 tgt CLAIMED DEVICE - disk 1 10/0.4.0 sdisk CLAIMED DEVICE SEAGATE ST15150W - target 2 10/0.5 tgt CLAIMED DEVICE - disk 2 10/0.5.0 sdisk CLAIMED DEVICE SEAGATE ST15150W - target 3 10/0.6 tgt CLAIMED DEVICE - disk 3 10/0.6.0 sdisk CLAIMED DEVICE SEAGATE ST15150W - target 4 10/0.7 tgt CLAIMED DEVICE - ctl 0 10/0.7.0 sctl CLAIMED DEVICE Initiator - bc 3 10/4 bc CLAIMED BUS_NEXUS Bus Converter - tty 0 10/4/0 mux2 CLAIMED INTERFACE MUX - ext_bus 1 10/4/4 scsi3 CLAIMED INTERFACE HP 28696A - - Wide SCSI ID=7 - tty 5 10/4/8 mux2 CLAIMED INTERFACE HP J2092A - - 16 RS-232 MUX - lan 0 10/4/12 token2 CLAIMED INTERFACE HP J2166A - - 802.5 Token Ring - LAN - tty 2 10/4/16 mux2 CLAIMED INTERFACE MUX - tty 3 10/4/17 mux2 CLAIMED INTERFACE MUX - ba 0 10/12 bus_adapter CLAIMED BUS_NEXUS Core I/O Adapter - ext_bus 3 10/12/0 CentIf CLAIMED INTERFACE Built-in Parallel - Interface - ext_bus 2 10/12/5 c720 CLAIMED INTERFACE Built-in SCSI - target 5 10/12/5.0 tgt CLAIMED DEVICE - tape 0 10/12/5.0.0 stape CLAIMED DEVICE HP C1533A - target 6 10/12/5.2 tgt CLAIMED DEVICE - disk 4 10/12/5.2.0 sdisk CLAIMED DEVICE TOSHIBA CD-ROM - XM-5401TA - target 7 10/12/5.7 tgt CLAIMED DEVICE - ctl 1 10/12/5.7.0 sctl CLAIMED DEVICE Initiator - lan 1 10/12/6 lan2 CLAIMED INTERFACE Built-in LAN - ps2 0 10/12/7 ps2 CLAIMED INTERFACE Built-in - Keyboard/Mouse - processor 0 32 processor CLAIMED PROCESSOR Processor - processor 1 34 processor CLAIMED PROCESSOR Processor - memory 0 49 memory CLAIMED MEMORY Memory Looking at the above, and comparing to the dmesg output, only 10/12 is getting successfully scanned. 10/ (which is where the "interesting" scsi host adapter is) isn't being reviewed at all. (yes, there is a SCSI host adapter directly on the GSC bus.) 10/4 doesn't appear to be scanned either, but that may be as much because none of the devices on it (the 3 RS-232 MUXes, and the Token Ring LAN card) are supported. (I'd bet 10/4 is an EISA adapter, similar to what is used in the 735 and 755.) Oh, and those drives on the 10/0 are all HVD fast/wide SCSI drives. (if I'm remembering Seagate's nominclature correctly, and having operated enough of those drives, I should be... :D ) My biggest question: does the GSC bus enumerator look for anything besides the bus_adapter at 10/12? [and now, I'll return to the peanut gallery..] -- Eric Schnoebelen [email protected] http://www.cirr.com If there was anything that depressed him more than his own cynicism, it was that quite often it still wasn't as cynical as real life. -- Terry Pratchett, "Guards! Guards!"