Four disks on sparc64/softraid0 -- kernel panic
Raymond Lillard <[email protected]>
| Newsgroups | gmane.os.openbsd.sparc |
|---|---|
| Message-ID | <[email protected]> |
After Nick corrected me in a previous message, I decided to
build my system with just two disks. I was able to build the
system with root-on-softraid using sd0 & sd1 to make a raid1
sd2 and all seems well. I have booted the two disk system
several times and it always comes up with all the pieces.
I am goal to delpoy a mail server and small drop-box service
on a Sun Fire V210/V240,Netra 240.
I have 4 140GB drives and want to configure sd0 & sd1 as
root-on-softraid and use sd2 & sd3 as a raid1 home partition.
sd4 will be a raid1 device with root and the OpenBSD OS
sd5 will be a raid1 device on /home
This fails, details follow. I can assemble such a system when
booting from bsd.rd, but when I boot from the real OS, it panics.
After establishing that everything works as intended for
the two disk configuration, I inserted the drives sd2 & sd3.
These drives had been previously wiped while booted up on bsd.rd.
The first boot attempt resulted in a kernel panic. I powered
down, removed sd2 & sd3, and rebooted to verify my two disk
installation was still intact. It was.
I then powered down again and re-inserted sd2 & sd3. This time
the machine booted up correctly. This is a mystery as I did
nothing to the sd2 & sd3 drives except remove and re-insert them.
I have pasted the console log below for the first boot failure
and the second boot success?
After booting successfully with all four disks in the machine,
I was able to assemble a raid1 as sd5 and do a newfs. I did
not put it into the fstab and rebooted. It panicked. I will
document that in the message that follows. these console logs
get quite long.
Here are two console logs:
I will post the trace and ps info in a second message. I think
in might be useful to look at these two, the only difference being
a machine power cycle.
#################################################################################################
The first 4 disk boot attempt
#################################################################################################
SC Alert: DISK @ HDD2 has been inserted.
SC Alert: DISK @ HDD3 has been inserted.
{1} ok boot disk0
@(#)OBP 4.17.1 2005/04/11 14:25 Sun Fire V210/V240,Netra 240
Clearing TLBs
Loading Configuration
Membase: 0000.0012.0000.0000
MemSize: 0000.0000.4000.0000
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Scrubbing Tomatillo tags... 0 1
Block Scrubbing Done
Find dropin, Copying Done, Size 0000.0000.0000.6cb0
PC = 0000.07ff.f000.5ba8
PC = 0000.0000.0000.5c58
Find dropin, (copied), Decompressing Done, Size 0000.0000.0006.7f00
Diagnostic console initialized
System Reset: CPU Reset
Probing system devices
jbus at 0,0 SUNW,UltraSPARC-IIIi (1503 MHz @ 9:1, 1 MB) memory-controller
jbus at 1,0 SUNW,UltraSPARC-IIIi (1503 MHz @ 9:1, 1 MB) memory-controller
jbus at 1f,0 pci
jbus at 1e,0 pci
jbus at 1c,0 pci
jbus at 1d,0 pci
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device SUNW,fru-device
SUNW,asr
Loading onboard drivers:
/pci@1e,600000: Device 7 isa
/pci@1e,600000/isa@7: flashprom rtc i2c power serial serial serial rmc-comm
/pci@1e,600000/isa@7/i2c@0,320: i2c-bridge i2c-bridge motherboard-fru-prom
chassis-fru-prom power-supply-fru-prom power-supply-fru-prom dimm-spd dimm-spd dimm-spd
dimm-spd dimm-spd dimm-spd dimm-spd dimm-spd rscrtc nvram idprom gpio gpio gpio gpio
gpio gpio
Probing memory
CPU 0 Bank 0 base 0 size 1024 MB
CPU 0 Bank 2 base 200000000 size 1024 MB
CPU 1 Bank 0 base 1000000000 size 1024 MB
CPU 1 Bank 2 base 1200000000 size 1024 MB
Probing I/O buses
/pci@1d,700000: Device 2 network network
/pci@1f,700000: Device 2 network network
/pci@1e,600000: Device 6 pmu i2c gpio
/pci@1e,600000/pmu@6/i2c@0,0:
/pci@1e,600000: Device a usb
/pci@1e,600000: Device d ide disk cdrom
/pci@1e,600000: Device 2 Nothing there
/pci@1e,600000: Device 3 Nothing there
/pci@1c,600000: Device 2 scsi disk tape scsi disk tape
/pci@1c,600000: Device 1 Nothing there
/pci@1d,700000: Device 1 SUNW,XVR-100
System Reset: CPU Reset
Probing system devices
jbus at 0,0 SUNW,UltraSPARC-IIIi (1503 MHz @ 9:1, 1 MB) memory-controller
jbus at 1,0 SUNW,UltraSPARC-IIIi (1503 MHz @ 9:1, 1 MB) memory-controller
jbus at 1f,0 pci
jbus at 1e,0 pci
jbus at 1c,0 pci
jbus at 1d,0 pci
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device SUNW,fru-device
SUNW,asr
Loading onboard drivers:
/pci@1e,600000: Device 7 isa
/pci@1e,600000/isa@7: flashprom rtc i2c power serial serial serial rmc-comm
/pci@1e,600000/isa@7/i2c@0,320: i2c-bridge i2c-bridge motherboard-fru-prom
chassis-fru-prom power-supply-fru-prom power-supply-fru-prom dimm-spd dimm-spd dimm-spd
dimm-spd dimm-spd dimm-spd dimm-spd dimm-spd rscrtc nvram idprom gpio gpio gpio gpio
gpio gpio
Probing memory
CPU 0 Bank 0 base 0 size 1024 MB
CPU 0 Bank 2 base 200000000 size 1024 MB
CPU 1 Bank 0 base 1000000000 size 1024 MB
CPU 1 Bank 2 base 1200000000 size 1024 MB
Probing I/O buses
/pci@1d,700000: Device 2 network network
/pci@1f,700000: Device 2 network network
/pci@1e,600000: Device 6 pmu i2c gpio
/pci@1e,600000/pmu@6/i2c@0,0:
/pci@1e,600000: Device a usb
/pci@1e,600000: Device d ide disk cdrom
/pci@1e,600000: Device 2 Nothing there
/pci@1e,600000: Device 3 Nothing there
/pci@1c,600000: Device 2 scsi disk tape scsi disk tape
/pci@1c,600000: Device 1 Nothing there
/pci@1d,700000: Device 1 SUNW,XVR-100
Sun Fire V240, No Keyboard
Copyright 2005 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.17.1, 4096 MB memory installed, Serial #51687930.
Ethernet address 0:3:ba:14:b1:fa, Host ID: 8314b1fa.
Rebooting with command: boot disk0
Boot device: /pci@1c,600000/scsi@2/disk@0,0 File and args:
OpenBSD IEEE 1275 Bootblock 1.3
..>> OpenBSD BOOT 1.4
Trying bsd...
Booting /pci@1c,600000/scsi@2/disk@0,0:a/bsd
6630864@0x1000000+4656@0x1652dd0+174864@0x1800000+4019440@0x182ab10
symbols @ 0xfeccc3c0 156+408792+257999 start=0x1000000
[ using 667912 bytes of bsd ELF symbol table ]
console is /pci@1e,600000/isa@7/serial@0,3f8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2013 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.3-current (GENERIC.MP) #79: Wed Apr 10 01:18:46 MDT 2013
[email protected]:/usr/src/sys/arch/sparc64/compile/GENERIC.MP
real mem = 4294967296 (4096MB)
avail mem = 4214972416 (4019MB)
mainbus0 at root: Sun Fire V240
cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1503 MHz
cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
cpu1 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1503 MHz
cpu1: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
"memory-controller" at mainbus0 not configured
"memory-controller" at mainbus0 not configured
schizo0 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
schizo0: dvma map c0000000-dfffffff
pci0 at schizo0
bge0 at pci0 dev 2 function 0 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 (0x2003): ivec
0x7c8, address 00:03:ba:14:b1:fa
brgphy0 at bge0 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
bge1 at pci0 dev 2 function 1 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 (0x2003): ivec
0x7c9, address 00:03:ba:14:b1:fb
brgphy1 at bge1 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
schizo1 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 0
schizo1: dvma map c0000000-dfffffff
pci1 at schizo1
ebus0 at pci1 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
"flashprom" at ebus0 addr 0-fffff, 290-290 not configured
rtc0 at ebus0 addr 70-71: m5819p
pcfiic0 at ebus0 addr 320-321 ivec 0x2e
iic0 at pcfiic0
"SUNW,i2c-imax" at iic0 addr 0xb not configured
"SUNW,i2c-imax" at iic0 addr 0xc not configured
spdmem0 at iic0 addr 0x5b: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem1 at iic0 addr 0x5c: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem2 at iic0 addr 0x5d: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem3 at iic0 addr 0x5e: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem4 at iic0 addr 0x63: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem5 at iic0 addr 0x64: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem6 at iic0 addr 0x65: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem7 at iic0 addr 0x66: 512MB DDR SDRAM registered ECC PC2300CL2.5
"ds1307" at iic0 addr 0x68 not configured
"pca9555" at iic0 addr 0x22 not configured
"pca9555" at iic0 addr 0x23 not configured
"pca9555" at iic0 addr 0x25 not configured
"pca9555" at iic0 addr 0x34 not configured
"pca9555" at iic0 addr 0x44 not configured
"pca9556" at iic0 addr 0x38 not configured
power0 at ebus0 addr 800-82f ivec 0x20
com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
com0: console
com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
"rmc-comm" at ebus0 addr 3e8-3ef ivec 0x2c not configured
alipm0 at pci1 dev 6 function 0 "Acer Labs M7101 Power" rev 0x00: 223KHz clock
iic1 at alipm0
ohci0 at pci1 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec 0x7a7, version 1.0,
legacy support
pciide0 at pci1 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide0: using ivec 0x798 for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-28E-C, 1.4B> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Acer Labs OHCI root hub" rev 1.00/1.00 addr 1
schizo2 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
schizo2: dvma map c0000000-dfffffff
pci2 at schizo2
siop0 at pci2 dev 2 function 0 "Symbios Logic 53c1010-66" rev 0x01: ivec 0x729, using 8K
of on-board RAM
scsibus1 at siop0: 16 targets, initiator 7
sd0 at scsibus1 targ 0 lun 0: <FUJITSU, MAT3147N SUN146G, 0602> SCSI2 0/direct fixed
serial.FUJITSU_MAT3147N_SUN146G000519C01M6R_AAC0P5501M6R
sd0: 140009MB, 512 bytes/sector, 286739329 sectors
sd1 at scsibus1 targ 1 lun 0: <FUJITSU, MAP3147N SUN146G, 0501> SCSI2 0/direct fixed
serial.FUJITSU_MAP3147N_SUN146G00R01SHA_
sd1: 140009MB, 512 bytes/sector, 286739329 sectors
sd2 at scsibus1 targ 2 lun 0: <FUJITSU, MAT3147N SUN146G, 0602> SCSI2 0/direct fixed
serial.FUJITSU_MAT3147N_SUN146G000533C053YT_AAC0P58053YT
sd2: 140009MB, 512 bytes/sector, 286739329 sectors
sd3 at scsibus1 targ 3 lun 0: <FUJITSU, MAT3147N SUN146G, 0602> SCSI2 0/direct fixed
serial.FUJITSU_MAT3147N_SUN146G000519C01M72_AAC0P5501M72
sd3: 140009MB, 512 bytes/sector, 286739329 sectors
siop1 at pci2 dev 2 function 1 "Symbios Logic 53c1010-66" rev 0x01: ivec 0x728, using 8K
of on-board RAM
scsibus2 at siop1: 16 targets, initiator 7
schizo3 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
schizo3: dvma map c0000000-dfffffff
pci3 at schizo3
bge2 at pci3 dev 2 function 0 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 (0x2003): ivec
0x75c, address 00:03:ba:14:b1:fc
brgphy2 at bge2 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
bge3 at pci3 dev 2 function 1 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 (0x2003): ivec
0x75d, address 00:03:ba:14:b1:fd
brgphy3 at bge3 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
radeonfb0 at pci3 dev 1 function 0 "ATI Radeon VE" rev 0x00
radeonfb0: SUNW,375-3126, 1152x900
wsdisplay0 at radeonfb0 mux 1
wsdisplay0: screen 0 added (std, sun emulation)
siop0: target 0 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset xfers
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
scsibus4 at softraid0: 256 targets
siop0: target 1 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset xfers
error, DSP=0x58
softraid0: I/O error 5 on dev 0x703 at block 16
siop0: phase mismatch without command
siop0: unhandled scsi interrupt, sist=0x90 sstat1=0x5 DSA=0xffffffff DSP=0x2c0
siop0: scsi bus reset
siop0: target 0 now using tagged DT 8 bit async xfers
siop0: target 1 now using tagged DT 8 bit async xfers
sd2(siop0:2:0): cmd 0x40003fd5820 (tag 0) added to reset list
siop0: target 2 now using 8 bit async xfers
sd2(siop0:2:0): cmd 0x40003fd5820 (status 2) reset with status 6, xs->error 8
panic: sr_lock: lock not held
kdb breakpoint at 146e5e0
Stopped at Debugger+0x4: nop
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
IF RUNNING SMP, USE 'mach ddbcpu <#>' AND 'trace' ON OTHER PROCESSORS, TOO.
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb{0}>
SC Alert: Host system has shut down.
#################################################################################################
The second 4 disk boot attempt -- which I expeted to fail also - but it succeeded
#################################################################################################
SC Alert: DISK @ HDD2 has been inserted.
SC Alert: DISK @ HDD3 has been inserted.
{1} ok boot disk0
@(#)OBP 4.17.1 2005/04/11 14:25 Sun Fire V210/V240,Netra 240
Clearing TLBs
Loading Configuration
Membase: 0000.0012.0000.0000
MemSize: 0000.0000.4000.0000
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Scrubbing Tomatillo tags... 0 1
Block Scrubbing Done
Find dropin, Copying Done, Size 0000.0000.0000.6cb0
PC = 0000.07ff.f000.5ba8
PC = 0000.0000.0000.5c58
Find dropin, (copied), Decompressing Done, Size 0000.0000.0006.7f00
Diagnostic console initialized
System Reset: CPU Reset
Probing system devices
jbus at 0,0 SUNW,UltraSPARC-IIIi (1503 MHz @ 9:1, 1 MB) memory-controller
jbus at 1,0 SUNW,UltraSPARC-IIIi (1503 MHz @ 9:1, 1 MB) memory-controller
jbus at 1f,0 pci
jbus at 1e,0 pci
jbus at 1c,0 pci
jbus at 1d,0 pci
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device SUNW,fru-device
SUNW,asr
Loading onboard drivers:
/pci@1e,600000: Device 7 isa
/pci@1e,600000/isa@7: flashprom rtc i2c power serial serial serial rmc-comm
/pci@1e,600000/isa@7/i2c@0,320: i2c-bridge i2c-bridge motherboard-fru-prom
chassis-fru-prom power-supply-fru-prom power-supply-fru-prom dimm-spd dimm-spd dimm-spd
dimm-spd dimm-spd dimm-spd dimm-spd dimm-spd rscrtc nvram idprom gpio gpio gpio gpio
gpio gpio
Probing memory
CPU 0 Bank 0 base 0 size 1024 MB
CPU 0 Bank 2 base 200000000 size 1024 MB
CPU 1 Bank 0 base 1000000000 size 1024 MB
CPU 1 Bank 2 base 1200000000 size 1024 MB
Probing I/O buses
/pci@1d,700000: Device 2 network network
/pci@1f,700000: Device 2 network network
/pci@1e,600000: Device 6 pmu i2c gpio
/pci@1e,600000/pmu@6/i2c@0,0:
/pci@1e,600000: Device a usb
/pci@1e,600000: Device d ide disk cdrom
/pci@1e,600000: Device 2 Nothing there
/pci@1e,600000: Device 3 Nothing there
/pci@1c,600000: Device 2 scsi disk tape scsi disk tape
/pci@1c,600000: Device 1 Nothing there
/pci@1d,700000: Device 1 SUNW,XVR-100
System Reset: CPU Reset
Probing system devices
jbus at 0,0 SUNW,UltraSPARC-IIIi (1503 MHz @ 9:1, 1 MB) memory-controller
jbus at 1,0 SUNW,UltraSPARC-IIIi (1503 MHz @ 9:1, 1 MB) memory-controller
jbus at 1f,0 pci
jbus at 1e,0 pci
jbus at 1c,0 pci
jbus at 1d,0 pci
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device SUNW,fru-device
SUNW,asr
Loading onboard drivers:
/pci@1e,600000: Device 7 isa
/pci@1e,600000/isa@7: flashprom rtc i2c power serial serial serial rmc-comm
/pci@1e,600000/isa@7/i2c@0,320: i2c-bridge i2c-bridge motherboard-fru-prom
chassis-fru-prom power-supply-fru-prom power-supply-fru-prom dimm-spd dimm-spd dimm-spd
dimm-spd dimm-spd dimm-spd dimm-spd dimm-spd rscrtc nvram idprom gpio gpio gpio gpio
gpio gpio
Probing memory
CPU 0 Bank 0 base 0 size 1024 MB
CPU 0 Bank 2 base 200000000 size 1024 MB
CPU 1 Bank 0 base 1000000000 size 1024 MB
CPU 1 Bank 2 base 1200000000 size 1024 MB
Probing I/O buses
/pci@1d,700000: Device 2 network network
/pci@1f,700000: Device 2 network network
/pci@1e,600000: Device 6 pmu i2c gpio
/pci@1e,600000/pmu@6/i2c@0,0:
/pci@1e,600000: Device a usb
/pci@1e,600000: Device d ide disk cdrom
/pci@1e,600000: Device 2 Nothing there
/pci@1e,600000: Device 3 Nothing there
/pci@1c,600000: Device 2 scsi disk tape scsi disk tape
/pci@1c,600000: Device 1 Nothing there
/pci@1d,700000: Device 1 SUNW,XVR-100
Sun Fire V240, No Keyboard
Copyright 2005 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.17.1, 4096 MB memory installed, Serial #51687930.
Ethernet address 0:3:ba:14:b1:fa, Host ID: 8314b1fa.
Rebooting with command: boot disk0
Boot device: /pci@1c,600000/scsi@2/disk@0,0 File and args:
OpenBSD IEEE 1275 Bootblock 1.3
..>> OpenBSD BOOT 1.4
Trying bsd...
Booting /pci@1c,600000/scsi@2/disk@0,0:a/bsd
6630864@0x1000000+4656@0x1652dd0+174864@0x1800000+4019440@0x182ab10
symbols @ 0xfeccc3c0 156+408792+257999 start=0x1000000
[ using 667912 bytes of bsd ELF symbol table ]
console is /pci@1e,600000/isa@7/serial@0,3f8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2013 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.3-current (GENERIC.MP) #79: Wed Apr 10 01:18:46 MDT 2013
[email protected]:/usr/src/sys/arch/sparc64/compile/GENERIC.MP
real mem = 4294967296 (4096MB)
avail mem = 4214972416 (4019MB)
mainbus0 at root: Sun Fire V240
cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1503 MHz
cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
cpu1 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1503 MHz
cpu1: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
"memory-controller" at mainbus0 not configured
"memory-controller" at mainbus0 not configured
schizo0 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
schizo0: dvma map c0000000-dfffffff
pci0 at schizo0
bge0 at pci0 dev 2 function 0 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 (0x2003): ivec
0x7c8, address 00:03:ba:14:b1:fa
brgphy0 at bge0 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
bge1 at pci0 dev 2 function 1 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 (0x2003): ivec
0x7c9, address 00:03:ba:14:b1:fb
brgphy1 at bge1 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
schizo1 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 0
schizo1: dvma map c0000000-dfffffff
pci1 at schizo1
ebus0 at pci1 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
"flashprom" at ebus0 addr 0-fffff, 290-290 not configured
rtc0 at ebus0 addr 70-71: m5819p
pcfiic0 at ebus0 addr 320-321 ivec 0x2e
iic0 at pcfiic0
"SUNW,i2c-imax" at iic0 addr 0xb not configured
"SUNW,i2c-imax" at iic0 addr 0xc not configured
spdmem0 at iic0 addr 0x5b: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem1 at iic0 addr 0x5c: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem2 at iic0 addr 0x5d: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem3 at iic0 addr 0x5e: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem4 at iic0 addr 0x63: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem5 at iic0 addr 0x64: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem6 at iic0 addr 0x65: 512MB DDR SDRAM registered ECC PC2300CL2.5
spdmem7 at iic0 addr 0x66: 512MB DDR SDRAM registered ECC PC2300CL2.5
"ds1307" at iic0 addr 0x68 not configured
"pca9555" at iic0 addr 0x22 not configured
"pca9555" at iic0 addr 0x23 not configured
"pca9555" at iic0 addr 0x25 not configured
"pca9555" at iic0 addr 0x34 not configured
"pca9555" at iic0 addr 0x44 not configured
"pca9556" at iic0 addr 0x38 not configured
power0 at ebus0 addr 800-82f ivec 0x20
com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
com0: console
com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
"rmc-comm" at ebus0 addr 3e8-3ef ivec 0x2c not configured
alipm0 at pci1 dev 6 function 0 "Acer Labs M7101 Power" rev 0x00: 223KHz clock
iic1 at alipm0
ohci0 at pci1 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec 0x7a7, version 1.0,
legacy support
pciide0 at pci1 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide0: using ivec 0x798 for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-28E-C, 1.4B> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Acer Labs OHCI root hub" rev 1.00/1.00 addr 1
schizo2 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
schizo2: dvma map c0000000-dfffffff
pci2 at schizo2
siop0 at pci2 dev 2 function 0 "Symbios Logic 53c1010-66" rev 0x01: ivec 0x729, using 8K
of on-board RAM
scsibus1 at siop0: 16 targets, initiator 7
sd0 at scsibus1 targ 0 lun 0: <FUJITSU, MAT3147N SUN146G, 0602> SCSI2 0/direct fixed
serial.FUJITSU_MAT3147N_SUN146G000519C01M6R_AAC0P5501M6R
sd0: 140009MB, 512 bytes/sector, 286739329 sectors
sd1 at scsibus1 targ 1 lun 0: <FUJITSU, MAP3147N SUN146G, 0501> SCSI2 0/direct fixed
serial.FUJITSU_MAP3147N_SUN146G00R01SHA_
sd1: 140009MB, 512 bytes/sector, 286739329 sectors
sd2 at scsibus1 targ 2 lun 0: <FUJITSU, MAT3147N SUN146G, 0602> SCSI2 0/direct fixed
serial.FUJITSU_MAT3147N_SUN146G000533C053YT_AAC0P58053YT
sd2: 140009MB, 512 bytes/sector, 286739329 sectors
sd3 at scsibus1 targ 3 lun 0: <FUJITSU, MAT3147N SUN146G, 0602> SCSI2 0/direct fixed
serial.FUJITSU_MAT3147N_SUN146G000519C01M72_AAC0P5501M72
sd3: 140009MB, 512 bytes/sector, 286739329 sectors
siop1 at pci2 dev 2 function 1 "Symbios Logic 53c1010-66" rev 0x01: ivec 0x728, using 8K
of on-board RAM
scsibus2 at siop1: 16 targets, initiator 7
schizo3 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
schizo3: dvma map c0000000-dfffffff
pci3 at schizo3
bge2 at pci3 dev 2 function 0 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 (0x2003): ivec
0x75c, address 00:03:ba:14:b1:fc
brgphy2 at bge2 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
bge3 at pci3 dev 2 function 1 "Broadcom BCM5704C" rev 0x00, BCM5704 A3 (0x2003): ivec
0x75d, address 00:03:ba:14:b1:fd
brgphy3 at bge3 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
radeonfb0 at pci3 dev 1 function 0 "ATI Radeon VE" rev 0x00
radeonfb0: SUNW,375-3126, 1152x900
wsdisplay0 at radeonfb0 mux 1
wsdisplay0: screen 0 added (std, sun emulation)
siop0: target 0 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset xfers
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
scsibus4 at softraid0: 256 targets
siop0: target 1 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset xfers
siop0: target 2 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset xfers
siop0: target 3 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset xfers
sd4 at scsibus4 targ 1 lun 0: <OPENBSD, SR RAID 1, 005> SCSI2 0/direct fixed
sd4: 134006MB, 512 bytes/sector, 274446192 sectors
softraid0: volume sd4 is roaming, it used to be sd2, updating metadata
bootpath: /pci@1c,600000/scsi@2,0/disk@0,0
root on sd4a (737e8dd2e3023547.a) swap on sd4b dump on sd4b
swapctl: adding 810ebfb6b83b034a.b as swap device at priority 0
swapctl: adding e8897007425f88b5.b as swap device at priority 0
Automatic boot in progress: starting file system checks.
/dev/sd4a (737e8dd2e3023547.a): file system is clean; not checking
/dev/sd4d (737e8dd2e3023547.d): file system is clean; not checking
/dev/sd4e (737e8dd2e3023547.e): file system is clean; not checking
/dev/sd4f (737e8dd2e3023547.f): file system is clean; not checking
/dev/sd4g (737e8dd2e3023547.g): file system is clean; not checking
/dev/sd4h (737e8dd2e3023547.h): file system is clean; not checking
/dev/sd4i (737e8dd2e3023547.i): file system is clean; not checking
/dev/sd4j (737e8dd2e3023547.j): file system is clean; not checking
/dev/sd4k (737e8dd2e3023547.k): file system is clean; not checking
/dev/sd4l (737e8dd2e3023547.l): file system is clean; not checking
setting tty flags
pf enabled
starting network
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
savecore: /dev/sd4b: Device not configured
checking quotas: done.
clearing /tmp
starting pre-securelevel daemons:.
setting kernel security level: kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd sendmail inetd sndiod.
starting local daemons: cron.
Wed Apr 17 12:28:30 PDT 2013
OpenBSD/sparc64 (ps2.prosysmeg.com) (console)
login: root
Password:
Last login: Wed Apr 17 12:18:28 on console
OpenBSD 5.3-current (GENERIC.MP) #79: Wed Apr 10 01:18:46 MDT 2013
Welcome to OpenBSD: The proactively secure Unix-like operating system.
Please use the sendbug(1) utility to report bugs in the system.
Before reporting a bug, please try to reproduce it with the latest
version of the code. With bug reports, please try to ensure that
enough information to reproduce the problem is enclosed, and if a
known fix for it exists, include that as well.
You have mail.