Re: Network boot sun sparc t1000 fail
Belous Victor <[email protected]> Thu, 6 Jun 2019 11:38:31 +0300
| Newsgroups | gmane.os.openbsd.sparc |
|---|---|
| Message-ID | <[email protected]> |
Hi, Andrew
I don't create domains on my T1000
ares> showplatform
SUNW,SPARC-Enterprise-T1000
Chassis Serial Number: NNL0812010
Domain Status
------ ------
S0 Running
ares> showhost
SPARC-Enterprise-T1000 System Firmware 6.6.7 2008/09/29 09:42
Host flash versions:
OBP 4.29.0.a 2008/09/15 11:59
Hypervisor 1.6.7.a 2008/09/29 09:29
POST 4.29.0.a 2008/09/15 12:27
ares> showsc
Advanced Lights Out Manager CMT v1.6.5
Yesterday I installed openbsd on hard host x64 from usb. And got the
same with it
{0} ok boot
net:bootp,192.168.215.6,ofwboot.net,192.168.215.130,192.168.215.100,4,4,255.255.255.0
bsd.rd
SC Alert: Host System has Reset
ChassisSerialNumber NNL0812010
Atlas, Shpalernaya, 28 Sun T1000
Boot device:
/pci@7c0/pci@0/network@4:bootp,192.168.215.6,ofwboot.net,192.168.215.130,192.168.215.100,4,4,255.255.255.0
File and args: bsd.rd
1000 Mbps full duplex Link up
Timed out waiting for BOOTP/DHCP reply
Timed out waiting for BOOTP/DHCP reply
Timed out waiting for BOOTP/DHCP reply
Timed out waiting for BOOTP/DHCP reply
>> OpenBSD BOOT 1.12
1000 Mbps full duplex Link up
No response for RARP request
Using BOOTP protocol: ip address: 192.168.215.130, hostname: sparc,
netmask: 255.255.255.0, gateway: 192.168.215.100
root addr=192.168.215.6 path=/
open
/pci@7c0/pci@0/network@4:bootp,192.168.215.6,ofwboot.net,192.168.215.130,192.168.215.100,4,4,255.255.255.0/etc/random.seed:
Unknown error: code 13
1000 Mbps full duplex Link up
No response for RARP request
Using BOOTP protocol: ip address: 192.168.215.130, hostname: sparc,
netmask: 255.255.255.0, gateway: 192.168.215.100
root addr=192.168.215.6 path=/
open
/pci@7c0/pci@0/network@4:bootp,192.168.215.6,ofwboot.net,192.168.215.130,192.168.215.100,4,4,255.255.255.0/bsd.rd:
Unknown error: code 13
Boot: ares> break
And this output from server
arsenal# tcpdump -n -i vlan6 ether host 00:14:4f:c4:7d:d6
tcpdump: listening on vlan6, link-type EN10MB
10:53:56.252439 arp who-has 192.168.215.6 (ff:ff:ff:ff:ff:ff) tell
192.168.215.130
10:53:56.252455 arp reply 192.168.215.6 is-at 68:05:ca:35:fc:39
10:53:56.252997 192.168.215.130.32768 > 192.168.215.6.69: 20 RRQ
"ofwboot.net"
10:53:56.253101 192.168.215.6.48054 > 192.168.215.130.32768: udp 516
10:53:56.253741 192.168.215.130.32768 > 192.168.215.6.48054: udp 4
10:53:56.253787 192.168.215.6.48054 > 192.168.215.130.32768: udp 516
... (booting ofwboot.net)
10:53:56.322942 192.168.215.130.32768 > 192.168.215.6.48054: udp 4
10:54:32.088581 0.0.0.0.68 > 255.255.255.255.67: secs:2 [|bootp]
10:54:32.088778 192.168.215.6.67 > 192.168.215.130.68: secs:2
Y:192.168.215.130 S:192.168.215.6 sname "arsenal" [|bootp] [tos 0x10]
10:54:32.093629 arp who-has 192.168.215.6 tell 192.168.215.130
10:54:32.093644 arp reply 192.168.215.6 is-at 68:05:ca:35:fc:39
10:54:32.094194 192.168.215.130.1023 > 192.168.215.6.111: udp 76
10:54:32.094240 192.168.215.6.111 > 192.168.215.130.1023: udp 28
10:54:32.094775 192.168.215.130.1023 > 192.168.215.6.711: udp 68
10:54:32.094833 192.168.215.6.711 > 192.168.215.130.1023: udp 28
10:55:08.516439 192.168.215.130.68 > 255.255.255.255.67: secs:38 [|bootp]
10:55:08.516495 192.168.215.6.67 > 192.168.215.130.68: secs:38
Y:192.168.215.130 S:192.168.215.6 sname "arsenal" [|bootp] [tos 0x10]
10:55:08.521324 192.168.215.130.1022 > 192.168.215.6.711: udp 68
10:55:08.521369 192.168.215.6.711 > 192.168.215.130.1022: udp 28
I don't understand why rarp don't work.
04.06.2019 17:54, Andrew Grillet пишет:
> Hi,
> Do I understand you are trying to boot a guest domain on your T1000?
> With services provided by an AMD machine?
>
> Then the problem may lie in the configuration of bridging in the T1000
> Primary domain.
> Login to the primary, and check with ifconfig that
> - the vnet to the guest is up and working
> - the em to the AMD machine is up and running
> - the two are bridged.
>
> Also, run rarpd in debug mode and see if it says "Got packet" or similar.
>
> Having said that, I did not manage to get my guest domains to netboot from
> the primary when I tried this with
> OpenBSD 6.3 on my T1000 - I believe there was a bug in Arp/Rarp packet
> routing - and I have not tried again since.
> (But will be trying again soon). I have net-booted V100s with OBSD 6.5 on a
> primary on a T1000.
>
> I have configured my guests by giving them two vdisks - the second is a
> link to a bsd.rd image. Then
> ok boot disk1
> will get you there.
>
> I would prefer to netboot though.
>
> Andrew
>
>
> On Tue, 4 Jun 2019 at 13:02, Belous Victor <[email protected]> wrote:
>
>> 03.06.2019 16:40, Claudio Jeker пишет:
>>> On Mon, Jun 03, 2019 at 04:19:13PM +0300, Belous Victor wrote:
>>>> Thanks, Claudio Jeker
>>>>
>>>> 03.06.2019 15:39, Claudio Jeker пишет:
>>>>> On Mon, Jun 03, 2019 at 03:15:07PM +0300, Belous Victor wrote:
>>>>>> Hi!
>>>>>>
>>>>>> I can't boot the sparc t1000 server.
>>>>>>
>>>>>> I have openbsd installed on virtualbox, the config openbsd server it
>> is
>>>>>>
>>>>>> openbsd# uname -a
>>>>>> OpenBSD openbsd.centerinform. 6.5 GENERIC#3 amd64
>>>>>>
>>>>>> openbsd# cat /etc/ethers
>>>>>> 00:14:4f:c4:7d:d6 sparc
>>>>>>
>>>>>> openbsd# cat /etc/hosts
>>>>>> 127.0.0.1 localhost
>>>>>> ::1 localhost
>>>>>> 192.168.215.130 sparc
>>>>>> 192.168.215.131 openbsd
>>>>>>
>>>>>> openbsd# cat /etc/rc.conf.local
>>>>>> bootparamd_flags=
>>>>>> mountd_flags=
>>>>>> nfsd_flags=
>>>>>> ntpd_flags-"NO"
>>>>>> pf=NO
>>>>>> portmap_flags=
>>>>>> rarpd_flags="-al"
>>>>>> tftpd_flags="/tftpboot"
>>>>>>
>>>>>> openbsd# cat /etc/bootparams
>>>>>> sparc root=192.168.215.231:/bsd.rd
>>>>>>
>>>>> This is not correct. bootparams points to a directory that acts as the
>>>>> root directory on the sparc system.
>>>>> You can set it to /home/bvictor/install/sparc64 or some other place
>> where
>>>>> bsd.rd is located.
>>>> Now
>>>>
>>>> openbsd# cat /etc/bootparams
>>>> sparc root=192.168.215.231:/home/bvictor/install/sparc64
>>>> openbsd#
>>>>
>>>>
>>>>
>>>>>> {0} ok boot net
>>>>> You may want to use boot net bsd.rd (so that the bsd.rd kernel is
>> loaded).
>>>> {0} ok boot net bsd.rd
>>>>
>>>> SC Alert: Host System has Reset
>>>> ChassisSerialNumber NNL0812010
>>>>
>>>>
>>>>
>>>> Atlas, Shpalernaya, 28 Sun T1000
>>>>
>>>>
>>>>
>>>>
>>>> Boot device: /pci@7c0/pci@0/network@4 File and args: bsd.rd
>>>> 1000 Mbps full duplex Link up
>>>>>> OpenBSD BOOT 1.12
>>>> 1000 Mbps full duplex Link up
>>>> No response for RARP request
>>>> open /pci@7c0/pci@0/network@4/etc/random.seed: No such file or
>> directory
>>>> 1000 Mbps full duplex Link up
>>>> No response for RARP request
>>>> open /pci@7c0/pci@0/network@4/bsd.rd: No such file or directory
>>>>
>>>> Boot:
>>>>
>>>>
>>>>>> SC Alert: Host System has Reset
>>>>>> ChassisSerialNumber NNL0812010
>>>>>>
>>>>>>
>>>>>>
>>>>>> Atlas, Shpalernaya, 28 Sun T1000
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> Boot device: /pci@7c0/pci@0/network@4 File and args:
>>>>>> 1000 Mbps full duplex Link up
>>>>>>>> OpenBSD BOOT 1.12
>>>>>> Trying bsd...
>>>>>> 1000 Mbps full duplex Link up
>>>>>> No response for RARP request
>>>>>> open /pci@7c0/pci@0/network@4/etc/random.seed: No such file or
>> directory
>>>>>> 1000 Mbps full duplex Link up
>>>>>> No response for RARP request
>>>>>> open /pci@7c0/pci@0/network@4/bsd: No such file or directory
>>>>>>
>>>>> Not sure what is up with 'No response for RARP request'. In the end you
>>>>> already got ofwboot.net loaded via tftp. It is possile that the T1000
>> is
>>>>> using dhcp for this and so the RARP is not fully working (at least the
>>>>> tcpdump output had no RARP packets in it).
>>>> I thinks, OpenBSD BOOT uses RARP, but with errors. Tcpdump show, it
>> don't
>>>> sent ARP request correct
>>>>
>>>> 16:13:20.544694 0.0.0.0.bootpc > 255.255.255.255.bootps: secs:2 [|bootp]
>>>> 0000: 4500 0148 0000 0000 0411 b5a6 0000 0000 E..H............
>>>> 0010: ffff ffff 0044 0043 0134 7168 0101 0600 .....D.C.4qh....
>>>> 0020: 0000 0000 0002 0000 0000 0000 0000 0000 ................
>>>> 0030: 0000 0000 0000 0000 0014 4fc4 7dd6 0000 ..........O.}...
>>>> 0040: 0000 0000 0000 0000 0000 0000 0000 0000 ................
>>>> 0050: 0000 0000 0000 0000 0000 0000 0000 0000 ................
>>>> 0060: 0000 0000 0000 ......
>>>>
>>> This is not a RARP packet. So it seems your system is not receiving the
>>> RARP packets sent by ofwboot.net on the T1000. Since you mentioned that
>>> this is a virtual system it could be that the host is filtering the
>>> requests out. The bootloader will fall back to bootp if rarpd/bootparams
>>> fails.
>>> You may be able to setup dhcpd to load the kernel by setting a host entry
>>> for the sparc system with the full path to your NFS reachable bsd.rd as
>>> bootfile.
>>>
>> I stop firewall service on the host and no change.
>>
>> I installed dhcp server on openbsd with the config
>>
>> openbsd# cat /etc/dhcpd.conf
>> authoritative;
>> subnet 192.168.215.0 netmask 255.255.255.0 {
>> range 192.168.215.121 192.168.215.129;
>> option routers 192.168.215.100;
>> option broadcast-address 192.168.215.255;
>> option domain-name-servers 192.168.215.100;
>> option domain-name "centerinform";
>> }
>> host sparc {
>> hardware ethernet 00:14:4f:c4:7d:d6;
>> option host-name "sparc";
>> fixed-address 192.168.215.130;
>> option root-path "192.168.215.130:/home/bvictor/install/root";
>> server-name "openbsd";
>> filename "ofwboot.net";
>> allow bootp;
>> next-server openbsd; }
>>
>> openbsd#
>>
>> and issue the next boot command
>>
>> {0} ok boot net:dhcp bsd.rd
>>
>> SC Alert: Host System has Reset
>> ChassisSerialNumber NNL0812010
>>
>>
>>
>> Atlas, Shpalernaya, 28 Sun T1000
>>
>>
>>
>>
>> Boot device: /pci@7c0/pci@0/network@4:dhcp File and args: bsd.rd
>> 1000 Mbps full duplex Link up
>> Timed out waiting for BOOTP/DHCP reply
>> Timed out waiting for BOOTP/DHCP reply
>> Timed out waiting for BOOTP/DHCP reply
>> >> OpenBSD BOOT 1.12
>> 1000 Mbps full duplex Link up
>> No response for RARP request
>> Using BOOTP protocol: ip address: 192.168.215.130, hostname: sparc,
>> netmask: 255.255.255.0, gateway: 192.168.215.100
>> root addr=192.168.215.131 path=/
>> open /pci@7c0/pci@0/network@4:dhcp/etc/random.seed: Unknown error: code 13
>> 1000 Mbps full duplex Link up
>> No response for RARP request
>> Using BOOTP protocol: ip address: 192.168.215.130, hostname: sparc,
>> netmask: 255.255.255.0, gateway: 192.168.215.100
>> root addr=192.168.215.131 path=/
>> open /pci@7c0/pci@0/network@4:dhcp/bsd.rd: Unknown error: code 13
>>
>> Boot: ares> break
>>
>> Then I run next command
>>
>>
>> {0} ok boot net bsd.rd
>>
>> SC Alert: Host System has Reset
>> ChassisSerialNumber NNL0812010
>>
>>
>>
>> Atlas, Shpalernaya, 28 Sun T1000
>>
>>
>>
>>
>> Boot device: /pci@7c0/pci@0/network@4 File and args: bsd.rd
>> 1000 Mbps full duplex Link up
>> >> OpenBSD BOOT 1.12
>> 1000 Mbps full duplex Link up
>> No response for RARP request
>> Using BOOTP protocol: ip address: 192.168.215.130, hostname: sparc,
>> netmask: 255.255.255.0, gateway: 192.168.215.100
>> root addr=192.168.215.131 path=/
>> open /pci@7c0/pci@0/network@4/etc/random.seed: Unknown error: code 13
>> 1000 Mbps full duplex Link up
>> No response for RARP request
>> Using BOOTP protocol: ip address: 192.168.215.130, hostname: sparc,
>> netmask: 255.255.255.0, gateway: 192.168.215.100
>> root addr=192.168.215.131 path=/
>> open /pci@7c0/pci@0/network@4/bsd.rd: Unknown error: code 13
>>
>> Boot:
>>
>>
>> On openbsd
>>
>> openbsd# tcpdump -s 1024 ether host 00:14:4f:c4:7d:d6
>> tcpdump: listening on em0, link-type EN10MB
>> 14:45:56.463418 arp who-has openbsd (Broadcast) tell sparc
>> 14:45:56.463486 arp reply openbsd is-at 08:00:27:40:f1:e2
>> 14:45:56.464143 sparc.32768 > openbsd.tftp: 20 RRQ "ofwboot.net"
>> 14:45:56.464536 openbsd.15993 > sparc.32768: udp 516
>>
>> ..... (boot ofwboot.net)
>>
>>
>> 14:46:30.933771 0.0.0.0.bootpc > 255.255.255.255.bootps: vend-rfc1048
>> 14:46:30.934324 openbsd.bootps > sparc.bootpc: Y:sparc S:openbsd sname
>> "openbsd" file "ofwboot.net" vend-rfc1048 SM:255.255.255.0
>> DG:192.168.215.100 NS:192.168.215.100 HN:"sparc" DN:"centerinform"
>> BR:192.168.215.255 [tos 0x10]
>> 14:46:30.938928 arp who-has openbsd tell sparc
>> 14:46:30.939026 arp reply openbsd is-at 08:00:27:40:f1:e2
>> 14:46:30.939692 sparc.1023 > openbsd.sunrpc: udp 76
>> 14:46:30.939867 openbsd.sunrpc > sparc.1023: udp 28
>> 14:46:30.940560 sparc.1023 > openbsd.1008: udp 68
>> 14:46:30.940784 openbsd.1008 > sparc.1023: udp 28
>> 14:47:07.400305 sparc.bootpc > 255.255.255.255.bootps: secs:36
>> vend-rfc1048
>> 14:47:07.400706 openbsd.bootps > sparc.bootpc: secs:36 Y:sparc
>> S:openbsd sname "openbsd" file "ofwboot.net" vend-rfc1048
>> SM:255.255.255.0 DG:192.168.215.100 NS:192.168.215.100 HN:"sparc"
>> DN:"centerinform" BR:192.168.215.255 [tos 0x10]
>> 14:47:07.406739 sparc.1022 > openbsd.1008: udp 68
>> 14:47:07.406922 openbsd.1008 > sparc.1022: udp 28
>>
>>
>> On the host computer, where run virtualbox openbsd I switch off the
>> firewoll and have the next packets
>>
>> [root@tpm ~]# tcpdump -s 1024 -i enp4s0f0 ether host 00:14:4f:c4:7d:d6
>> tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
>> listening on enp4s0f0, link-type EN10MB (Ethernet), capture size 1024 bytes
>> 14:45:56.467016 ARP, Request who-has openbsd (Broadcast) tell sparc,
>> length 50
>> 14:45:56.467347 ARP, Reply openbsd is-at 08:00:27:40:f1:e2 (oui
>> Unknown), length 50
>> 14:45:56.467793 IP sparc.filenet-tms > openbsd.tftp: 20 RRQ
>> "ofwboot.net" octet
>> 14:45:56.468408 IP openbsd.15993 > sparc.filenet-tms: UDP, length 516
>> 14:45:56.468916 IP sparc.filenet-tms > openbsd.15993: UDP, length 4
>>
>>
>> ... (boot the ofwboot.net)
>>
>> 14:45:56.557471 IP sparc.filenet-tms > openbsd.15993: UDP, length 4
>> 14:46:30.938023 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP,
>> Request from 00:14:4f:c4:7d:d6 (oui Unknown), length 300
>> 14:46:30.938830 IP openbsd.bootps > sparc.bootpc: BOOTP/DHCP, Reply,
>> length 300
>> 14:46:30.943206 ARP, Request who-has openbsd tell sparc, length 50
>> 14:46:30.943519 ARP, Reply openbsd is-at 08:00:27:40:f1:e2 (oui
>> Unknown), length 50
>> 14:46:30.944047 IP sparc.1023 > openbsd.sunrpc: UDP, length 76
>> 14:46:30.944383 IP openbsd.sunrpc > sparc.1023: UDP, length 28
>> 14:46:30.944825 IP sparc.1023 > openbsd.1008: UDP, length 68
>> 14:46:30.945301 IP openbsd.1008 > sparc.1023: UDP, length 28
>> 14:47:07.404672 IP sparc.bootpc > 255.255.255.255.bootps: BOOTP/DHCP,
>> Request from 00:14:4f:c4:7d:d6 (oui Unknown), length 300
>> 14:47:07.405298 IP openbsd.bootps > sparc.bootpc: BOOTP/DHCP, Reply,
>> length 300
>> 14:47:07.410320 IP sparc.exp2 > openbsd.1008: UDP, length 68
>> 14:47:07.410851 IP openbsd.1008 > sparc.exp2: UDP, length 28
>>
>> I have no ideas who don't work rarp.
>>
>>
>>
>>
>> --
>> С уважением,
>> Виктор Антонович Белоус
>>
>>
--
С уважением,
Виктор Антонович Белоус