ZeusIOPS multipathing failed solaris 11

hi, 

just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA
(x4440 + j4400), but when I enable multipathing with "stmsboot -e", only
the 1TB SATA drives inside the j4400 are configured as multipathed vhci
/ mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the
server is connected with two SAS HBAs to the j4400 storage 

------


s11.1# echo | format | grep c0t5000C50010C79068d0
 22.
c0t5000C50010C79068d0 <ATA-SEAGATE ST31000N-SU0F-931.51GB> 

s11.1#
stmsboot -L | grep c0t5000C50010C79068d0
/dev/rdsk/c11t20d0
/dev/rdsk/c0t5000C50010C79068d0
/dev/rdsk/c10t120d0
/dev/rdsk/c0t5000C50010C79068d0 

s11.1# mpathadm list lu
/dev/dsk/c0t5000C50010C79068d0s2 

mpath-support: libmpscsi_vhci.so

/dev/rdsk/c0t5000C50010C79068d0s2
 Total Path Count: 2
 Operational Path
Count: 2 

s11.1# echo | format | grep -i zeus 

 4. c10t104d0 <ATA-STEC
ZeusIOPS-0430-17.00GB>
 5. c11t4d0 <ATA-STEC ZeusIOPS-0430-17.00GB>
 9.
c10t108d0 <ATA-STEC ZeusIOPS-0430-17.00GB>
 10. c11t8d0 <ATA-STEC
ZeusIOPS-0430-17.00GB> 

------ 

Found a setting on another ZFSSA
running the fishworks solaris os (Solaris 11 Express snv_151 || ZFSSA
2011.1.6) in the kernel.drv directory: 

ss7410# tail -2
/kernel/drv/sd.conf
sd-config-list="*Z16IZF2EUSUN73G*",
"logzilla-config", "*Z16IZF3EUSUN73G*", "logzilla-config",
"*ZeusIOPs-G3*", "logzilla-config", "*ZeusIOP*", "logzilla-config",
"ZeusRAM", "logzilla-config", "*SD88S*", "logzilla-config",
"*-HBA-NVRAM-*",
"logzilla-config";
logzilla-config=1,0x40000,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1;


I've tried these settings on the solaris 11.1 installation, also with
'mpxio-disable="no";' and 'disable-sata-mpxio="no";' in
/kernel/drv/mpt.conf & /kernel/drv/mpt_sas.conf, but solaris fails to
enable the multipathing... 

it should work, the ZFSSA uses the vhci
path: 

ss7410# echo | format | grep -i zeus
 48.
c4tATASTECZEUSIOPS018GBYTESSTM0000C1C6Bd0 <ATA-STEC
ZeusIOPS-0430-17.00GB>

/scsi_vhci/disk@gATASTECZeusIOPS018GBytesSTM0000C1C6B 

no 'mpathadm' to
prove the 2nd path on the ZFSSA solaris... 

tried several variations in
the sd.conf, but it doesn't work: 

sd-config-list="*Z16IZF2EUSUN73G*",
"logzilla-config", "*Z16IZF3EUSUN73G*", "logzilla-config",
"*ZeusIOPs-G3*", "logzilla-config", "*ZeusIOP*", "logzilla-config",
"ZeusRAM", "logzilla-config", "*SD88S*", "logzilla-config",
"*-HBA-NVRAM-*", "logzilla-config", "ZeusIOPS-0430-17.00GB",
"logzilla-config", "*ATA-STEC*", "logzilla-config", "ATA-STEC
ZeusIOPS-0430-17.00GB", "logzilla-config", "STEC ZeusIOPS",
"logzilla-config", "*STEC*",
"logzilla-config";
logzilla-config=1,0x40000,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1;


Did I forget so tell solaris somewhere to look into that sd.conf
file... running out of ideas, any hints? 

thanks in advance, 

regards
- pressy