installing KGPSA-CX (HBA)

I just installed a KGPSA-CX on an AS 800 running 5.1A PK6.  Seems to
have installed correctly:
 
root@sif==> emxmgr -t emx0
 
emx0 state information:
  Link :  connection is DOWN
  Link is SCSI bus 3 (e.g. scsi3)
          SCSI target id -1
          portname is 1000-0000-C923-BA1E
          nodename is 2000-0000-C923-BA1E
  There are no connected N_Ports in the topology

 
from /var/adm/messages:
                                        emx0 at pci0 slot 14
                                        KGPSA-CA : Driver Rev 2.11 : F/W
Rev
                                         _3.91A1(2.20A0) : wwn
                                         _1000-0000-c923-ba1e
                                        emx0: Using console topology
setting
                                         _of : Fabric
                                        emx0: emx_linkup_timedout: link
up
                                         _timeout has expired

We are going to connect this to a SAN (3PAR) but haven't done that yet
(i.e., no cabling is connecting this HBA and the SAN).  Is that why the
first message says "connection is DOWN"?

Also, how do I get the OS to see this?  

When I issue:

root@sif==> hwmgr -show scsi

        SCSI                DEVICE    DEVICE  DRIVER NUM  DEVICE FIRST
 HWID:  DEVICEID HOSTNAME   TYPE      SUBTYPE OWNER  PATH FILE   VALID
PATH
------------------------------------------------------------------------
-
   40:  0        sif        disk      none    2      1    dsk0   [0/0/0]
   41:  1        sif        cdrom     none    0      1    cdrom0 [0/4/0]
   42:  3        sif        disk      none    2      1    dsk1   [1/0/0]
   43:  4        sif        disk      none    0      1    dsk2   [1/1/0]
   44:  5        sif        disk      none    2      1    dsk3   [1/3/0]
   45:  6        sif        disk      none    2      1    dsk4   [1/4/0]
   46:  7        sif        disk      none    0      1    (null)
   47:  8        sif        disk      none    2      1    dsk6   [2/0/0]
   49:  10       sif        disk      none    2      1    dsk8   [2/3/0]
   50:  11       sif        disk      none    2      1    dsk9   [2/4/0]
   51:  2        sif        tape      none    0      1    tape0  [0/5/0]
   52:  12       sif        disk      none    0      1    (null)
   53:  13       sif        disk      none    2      1    dsk11  [2/5/0]
   54:  14       sif        disk      none    0      1    (null)
   55:  9        sif        disk      none    0      1    dsk13  [2/1/0]
   56:  15       sif        disk      none    2      2    dsk14  [2/6/0]
   57:  16       sif        disk      none    2      1    dsk15  [1/6/0]
   58:  17       sif        disk      none    2      1    dsk16  [1/2/0]
   59:  18       sif        disk      none    2      1    dsk17  [1/5/0]

And:

root@sif==> scu show edt

CAM Equipment Device Table (EDT) Information:

    Bus/Target/Lun Device Type  ANSI  Vendor ID    Product ID
Revision N/W
    -------------- ----------- ------ --------- ----------------
-------- ---
     0    0    0   Direct      SCSI-2 DEC       RZ1CB-CA (C) DEC   LYJ0
W
     0    4    0   CD-ROM      SCSI-2 DEC       RRD47   (C) DEC    1206
N
     0    5    0   Sequential  SCSI-2 DEC       TLZ09     (C)DEC   0173
N
     1    0    0   Direct      SCSI-2 DEC       RZ1CB-CS (C) DEC   0656
W
     1    1    0   Direct      SCSI-2 DEC       RZ1CF-CF (C) DEC   1614
W
     1    2    0   Direct      SCSI-3 COMPAQ    BD0366459B         B016
W
     1    3    0   Direct      SCSI-2 DEC       RZ1CB-CS (C) DEC   0656
W
     1    4    0   Direct      SCSI-2 DEC       RZ1EF-CB (C) DEC   0370
W
     1    5    0   Direct      SCSI-2 COMPAQ    BD0366459B         B010
W
     1    6    0   Direct      SCSI-2 COMPAQ    BD0366459B         B010
W
     2    0    0   Direct      SCSI-2 DEC       RZ2ED-LS (C) DEC   0306
W
     2    1    0   Direct      SCSI-3 COMPAQ    BD01865CC4         HPB6
W
     2    3    0   Direct      SCSI-2 COMPAQ    BD036635C5         B020
W
     2    4    0   Direct      SCSI-2 COMPAQ    BD036635C5         B020
W
     2    5    0   Direct      SCSI-2 COMPAQ    BD018122C0         3B09
W
     2    6    0   Direct      SCSI-3 COMPAQ    BD0366459B         B016
W

I don't see anything I would recognize as the HBA.  Am I overlooking it
or do I need to run something?

The driver is 2.11 -- do I need a more recent one?  I can't find
anything for this on the HP ITRC site.

Thanks!
Andy