Re: Re: no receive on am
CHARLES DAVID JORDAN <[email protected]>
| Newsgroups | gmane.recreation.radio.hardware.yaesu.vr-5000 |
|---|---|
| Message-ID | <[email protected]> |
yes ive got squelch turned all the way down --- On Sun, 11/28/10, jim_hack <[email protected]> wrote: From: jim_hack <[email protected]> Subject: [YaesuVR-5000] Re: no receive on am To: [email protected] Date: Sunday, November 28, 2010, 10:46 AM Dumb question but: Have you checked to make sure the squelch knob is not turned partially. This happened to me once. --- In [email protected], CHARLES DAVID JORDAN <cdjordan523@...> wrote: > > no i can not, but when i get off work this afternoon ill try different bands on the sub band > > --- On Sat, 11/27/10, majoco21 <martin_cook@...> wrote: > > From: majoco21 <martin_cook@...> > Subject: [YaesuVR-5000] Re: no receive on am > To: [email protected] > Date: Saturday, November 27, 2010, 10:13 PM > > > > > > > >  > > > > > > > > > > Ok, now here's another thought. Can you tune the sub VFO to an AM broadcast station and receive it, 'cos in theory according to the block diagram, they use separate detectors..... > > > > Cheers - Martin ZL2MC > > > > --- In [email protected], CHARLES DAVID JORDAN <cdjordan523@> wrote: > > > > > > i did the reset, no good. right now ive got it tuned to a local radio station in lexington, ky. 0.63000  am. if i skip through the modes when it comes back to am it will show a signal for just a instant > > > > > > > > > > > > --- On Sat, 11/27/10, majoco21 <martin_cook@> wrote: > > > > > > From: majoco21 <martin_cook@> > > > Subject: [YaesuVR-5000] Re: no receive on am > > > To: [email protected] > > > Date: Saturday, November 27, 2010, 8:59 PM > > > > > > > > > > > > > > > > > > > > > > > >  > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > I gave up on FTBCat, found it was more for transceivers. Now I use FTBVR5K to just catalogue and organise my memory locations. Works a treat. Locking out the secondary VFO speeds up scanning too. > > > > > > > > > > > > Sorry, got OT. > > > > > > > > > > > > Hope that you haven't loaded something into the EEPROM to tell it something different. If you have downloaded all your frequencies and other info, I would be inclined to do a total microprocessor reset as per tha handbook page 56 next. > > > > > > > > > > > > Cheers - Martin ZL2MC > > > > > > > > > > > > --- In [email protected], "cdjordan523@" <cdjordan523@> wrote: > > > > > > > > > > > > > > i can go to fm and hit the band scope and it hits on all the local broadcast stations > > > > > > > > > > > > > > > > > > > > > > > > > > > > --- In [email protected], lambsona@ wrote: > > > > > > > > > > > > > > > > god point though on mine it only whacks out the SSB's > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > ----- Original Message ----- > > > > > > > > From: "G1ITV" <g1itv@> > > > > > > > > To: [email protected] > > > > > > > > Sent: Saturday, November 27, 2010 6:07:55 PM > > > > > > > > Subject: Re: [YaesuVR-5000] Re: no receive on am > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Have you got Band Scope activated ? > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > -------Original Message------- > > > > > > > > > > > > > > > > From: cdjordan523@ > > > > > > > > Date: 28/11/2010 00:57:51 > > > > > > > > To: [email protected] > > > > > > > > Subject: [YaesuVR-5000] Re: no receive on am > > > > > > > > > > > > > > > > I hooked another receiver up to the same coax and same antenna and it works, > > > > > > > > could it be a setting I have messed up or something inside of the radio. I > > > > > > > > usually use a cat program called ftbcat v1.15 > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > [Non-text portions of this message have been removed] > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > [Non-text portions of this message have been removed] > > > > > > > > > > > > > > > > > > > > > > > > > > [Non-text portions of this message have been removed] > [Non-text portions of this message have been removed]