RES: RES: LCD lines

Dear Richard,

 

Thank you for emailing us here at VERTEX STANDARD.  Below is the part and
ordering information.  Please email or call us at the number below if you
have any further questions.

 

 

 


Part Number

Description

Cost

Qty

NOTES


Q7000372

LCD MODULE NCM1703A

$91.08

1

IN STOCK 


 

 

 

 

 

Price(s) does not include tax (only if applied to your state) and/or freight
cost. If you wish to purchase this/these item(s), please contact our Parts
Department via email at [email protected] or call our office at
1-714-827-7600 ext 6800  Monday thru Friday between the hours of 8:00AM thru
5:00PM Pacific Standard Time and provide the following:

Name:

Shipping Address:

Phone Number

Our company policy: All orders must be pulled, packed and weighed to
determine shipping cost. Sorry, we cannot quote shipping cost in advanced.
We charge actual shipping cost(s).

Shipping Method: FedEx (Ground, Express Saver, 2Day, Overnight)

Payment Method (Visa, MC or AMEX which must include Exp. Date and V-code
which are the last 3 digits located on the back of the card in the signature
block to the far right side of the card. Ex. XXXXX-XXX):

-OR-

Money order or personal check, please send payment to the address listed
below. Once payment has been received, order will be processed.

VERTEX STANDARD

ATTN: PARTS DEPARTMENT

10900 WALKER STREET

CYPRESS, CA 90630

Thank you.

Joseph Lee

Vertex Standard Parts Representative

Vertex Standard USA, Inc. |  10900 Walker St.   | Cypress, CA 90630

[email protected] <mailto:[email protected]>  | 714-827-7600 x6800 |
fax 714-527-9472

 www.vertexstandard.com <http://www.vertexstandard.com/> 

 

This message (including any attachments) contains confidential information
intended for a specific individual and purpose, and is protected by law. If
you are not the intended recipient, you should delete this message. Any
disclosure, copying, or distribution of this message, or the taking of any
action based on it, is strictly prohibited.

 

 

 

-----Original Message-----
From: Scott Dolliver [mailto:[email protected]] 
Sent: Monday, August 15, 2011 4:33 PM
To: Joseph Lee
Subject: FW: Inquiry: Tech Support

 

 

 

-----Original Message-----

From: Jerry Darby [mailto:[email protected]] 

Sent: Monday, August 15, 2011 4:30 PM

To: Scott Dolliver

Subject: FW: Inquiry: Tech Support

 

 

 

 

-----Original Message-----

From: Web site inquiry [mailto:[email protected]] 

Sent: Sunday, August 14, 2011 7:17 AM

To: [email protected]

Subject: Inquiry: Tech Support

 

 

 

The following inquiry was made from www.yaesu.com on 8-14-11 at 7:16am:

 

Email Address: [email protected]

First Name: Richard

Last Name: Gerhke

City: Blumenau

State/Province: Santa Catarina - Brasil

Phone: 0055 47 33386191

Type: Tech Support

 

Hello

I am a happy owner of a Yaesu VR-5000, unfortunately he is free from

defects

in LCD.

I want to know if there selling this LCD to replace this missing two

vertical lines in the region of the clock.

With this LCD available, at what cost.

 

LCD Module Q7000372

 

 

De: [email protected] [mailto:[email protected]] Em
nome de Gerry Rolle
Enviada em: domingo, 14 de agosto de 2011 23:26
Para: [email protected]
Assunto: RE: RES: [YaesuVR-5000] LCD lines

 

  

If the loss of a few "lines" was the only problem, might be able to live
with it.

However, along with the lines, the display is growing dimmer.

I'm ordering the new software.

_____ 

From: [email protected] <mailto:YaesuVR-5000%40yahoogroups.com>
[mailto:[email protected] <mailto:YaesuVR-5000%40yahoogroups.com>
] On
Behalf Of majoco21
Sent: Sunday, August 14, 2011 7:12 PM
To: [email protected] <mailto:YaesuVR-5000%40yahoogroups.com> 
Subject: Re: RES: [YaesuVR-5000] LCD lines

Hi, 

Plenty of previous posts on this issue. I drilled the top and bottom case
halves to reduce the temperature which it has done, but no change in the
missing lines, both vertical and horizontal. I began to suspect the 100uF
capacitor on the back of the display board (which in my receiver is
parallelled by a 22000uF) and removed both of them and temporarily fitted a
new 22000uF but that made no difference. 

It seems strange that if the powere is removed for a few days, the number of
bad lines is increased but slowly reverts back to a stubborn few - today I
have only two verticals missing which go through the 'tens' of the channel
number. I guess I'll just live with it, or try the new software.

--- In [email protected] <mailto:YaesuVR-5000%40yahoogroups.com>
<mailto:YaesuVR-5000%40yahoogroups.com>
, "Richard Gerhke" <gerhke@...> wrote:
>
> Hello
> My VR5000 is also introducing LCD failure, is missing a vertical line in
the
> central region of the last character of the clock.
> Sera that Yaesu have this lcd for sale, I see that we are not alone with
> this defect, thequote is found on the internet concerning this problem.
> It no longer as of old equipment.
> 
> 
> 
> Richard Gerhke
> 
> <http://www.gerhke.com> www.gerhke.com
> 
> Brazil 
> 
> 
> 
> De: [email protected] <mailto:YaesuVR-5000%40yahoogroups.com>
<mailto:YaesuVR-5000%40yahoogroups.com>
[mailto:[email protected] <mailto:YaesuVR-5000%40yahoogroups.com>
<mailto:YaesuVR-5000%40yahoogroups.com>
] Em
> nome de nisangreenwich
> Enviada em: domingo, 14 de agosto de 2011 11:59
> Para: [email protected] <mailto:YaesuVR-5000%40yahoogroups.com>
<mailto:YaesuVR-5000%40yahoogroups.com>

> Assunto: [YaesuVR-5000] LCD lines
> 
> 
> 
> 
> 
> Hi guys,
> 
> I have an older vr-5000 which has developed loss of vertical LCD lines. On
> start up there are 5 lines missing and within an our it drops down to 2!
> (heat issue?)
> 
> Any ideas on how to correct this?
> 
> Thanks
> Nisan,
> Dublin
> 
> Sent from my iPad ...
> 
> 
> 
> 
> 
> [Non-text portions of this message have been removed]
>

[Non-text portions of this message have been removed]





[Non-text portions of this message have been removed]