Re: Probleme mit bind9

Hallo Marcus,

> Sind die NICs auch im alten und neuen System wieder mit den gleichen Netzen
> verbunde, also z. B. Nic1 mit Netz1, Nic2 mit Netz2, usw. Du verstehst, was
> ich meine?

Die vier bzw. fünf NICs sind onboard. (Eine NIC ist das IPMI-Interface 
und zählt nicht mit)

In der Base habe ich die neuen NIC-Namen enx002590xxxxxx entsprechend 
geändert. Nach einem neustart waren auch alle damit sofort UP.

 > Kannst du bitte mal die Netzwerkkonfiguration der Base posten?

Hier die Eth-Konfiguration aus der base:

IP_ETH_N='3'                           # number of ip ethernet networks

#------------------------------------------------------------------------------
# Ether networks card settings:
#------------------------------------------------------------------------------

IP_ETH_1_NAME='enx00259079d338'        # optional: other device name 
than enx*
IP_ETH_1_MACADDR=''                    # Mac address of your n'th 
ethernet card

#------------------------------------------------------------------------------
# Ether networks IPv4 settings:
#------------------------------------------------------------------------------

IP_ETH_1_V4_DHCP='no'                  # Use dhcp of this device
                                        # Use: yes or no
IP_ETH_1_V4_METHOD='manual'            # Use: manual, link-local or disabled
IP_ETH_1_V4_IP_N='1'                   # number of ip on network card
IP_ETH_1_V4_IP_1_IPADDR='192.168.128.122'
                                        # IP address of your n'th 
ethernet card
IP_ETH_1_V4_IP_1_NETWORK=''            # network of your LAN
IP_ETH_1_V4_IP_1_NETMASK='255.255.255.0'
                                        # netmask of your LAN


#------------------------------------------------------------------------------
# Additional routes and Gateway for IPv4:
#------------------------------------------------------------------------------

IP_ETH_1_V4_GATEWAY='192.168.128.1'    # your default gateway
IP_ETH_1_V4_ROUTE_N='0'                # number of additional routes


#------------------------------------------------------------------------------
# Ether networks IPv6 settings:
#------------------------------------------------------------------------------

IP_ETH_1_V6_DHCP='no'                  # Use dhcp of this device
                                        # Use: yes or no
IP_ETH_1_V6_ADDR_GEN_MODE='eui64'      # Use: eui64, stable-privacy
IP_ETH_1_V6_METHOD='link-local'        # Use: manual, link-local, ignore 
or disabled
IP_ETH_1_V6_IP_N='0'                   # number of ip on network card


#------------------------------------------------------------------------------
# Additional routes and Gateway for IPv6:
#------------------------------------------------------------------------------

IP_ETH_1_V6_GATEWAY='fe80::1'          # your default gateway
IP_ETH_1_V6_ROUTE_N='0'                # number of additional routes


#------------------------------------------------------------------------------
# Ether networks card settings:
#------------------------------------------------------------------------------

IP_ETH_2_NAME='enx00259079d339'
IP_ETH_2_MACADDR=''


#------------------------------------------------------------------------------
# Ether networks IPv4 settings:
#------------------------------------------------------------------------------

IP_ETH_2_V4_DHCP='no'
IP_ETH_2_V4_METHOD='manual'
IP_ETH_2_V4_IP_N='0'

#------------------------------------------------------------------------------
# Additional routes and Gateway for IPv4:
#------------------------------------------------------------------------------

IP_ETH_2_V4_GATEWAY=''
IP_ETH_2_V4_ROUTE_N='0'

#------------------------------------------------------------------------------
# Ether networks IPv6 settings:
#------------------------------------------------------------------------------

IP_ETH_2_V6_DHCP='no'
IP_ETH_2_V6_ADDR_GEN_MODE='eui64'
IP_ETH_2_V6_METHOD='link-local'
IP_ETH_2_V6_IP_N='0'

#------------------------------------------------------------------------------
# Additional routes and Gateway for IPv6:
#------------------------------------------------------------------------------

IP_ETH_2_V6_GATEWAY='fe80::1'
IP_ETH_2_V6_ROUTE_N='0'


#------------------------------------------------------------------------------
# Ether networks card settings:
#------------------------------------------------------------------------------

IP_ETH_3_NAME='enx00259079d33a'
IP_ETH_3_MACADDR=''

#------------------------------------------------------------------------------
# Ether networks IPv4 settings:
#------------------------------------------------------------------------------

IP_ETH_3_V4_DHCP='no'
IP_ETH_3_V4_METHOD='manual'
IP_ETH_3_V4_IP_N='0'

#------------------------------------------------------------------------------
# Additional routes and Gateway for IPv4:
#------------------------------------------------------------------------------

IP_ETH_3_V4_GATEWAY=''
IP_ETH_3_V4_ROUTE_N='0'

#------------------------------------------------------------------------------
# Ether networks IPv6 settings:
#------------------------------------------------------------------------------

IP_ETH_3_V6_DHCP='no'
IP_ETH_3_V6_ADDR_GEN_MODE='eui64'
IP_ETH_3_V6_METHOD='link-local'
IP_ETH_3_V6_IP_N='0'

#------------------------------------------------------------------------------
# Additional routes and Gateway for IPv6:
#------------------------------------------------------------------------------

IP_ETH_3_V6_GATEWAY='fe80::1'
IP_ETH_3_V6_ROUTE_N='0'


> 4:3:1 ist ja ein Index auf eine Netzwerkkonfiguration der Base; frage mich
> gerade, was die 4 bedeuten soll.

Das weiß ich nicht. Die war auch vorher schon da.. :-)

Gruß,
Wilhelm