Re: [PATCH 01/12] dt-bindings: i3c: Add mipi-i3c-static-method to support SETAASA

On 27/03/2026 13:48:58+0530, Akhil R wrote:
> On Thu, 26 Mar 2026 16:44:31 +0100, Alexandre Belloni wrote:
> > On 26/03/2026 10:05:03-0500, Rob Herring wrote:
> >> On Wed, Mar 18, 2026 at 05:31:50PM +0000, Conor Dooley wrote:
> >> > On Wed, Mar 18, 2026 at 10:57:14PM +0530, Akhil R wrote:
> >> > > Add the 'mipi-i3c-static-method' property mentioned in the MIPI I3C
> >> > > Discovery and Configuration Specification [1] to specify which discovery
> >> > > method an I3C device supports during bus initialization. The property is
> >> > > a bitmap, where a bit value of 1 indicates support for that method, and 0
> >> > > indicates lack of support.
> >> > > Bit 0: SETDASA CCC (Direct)
> >> > > Bit 1: SETAASA CCC (Broadcast)
> >> > > Bit 2: Other CCC (vendor / standards extension)
> >> > > All other bits are reserved.
> >> > > 
> >> > > It is specifically needed when an I3C device requires SETAASA for the
> >> > > address assignment. SETDASA will be supported by default if this property
> >> > > is absent - which means for now the property just serves as a flag to
> >> > > enable SETAASA, but keep the property as a bitmap to align with the
> >> > > specifications.
> >> > > 
> >> > > [1] https://www.mipi.org/specifications/disco
> >> > > 
> >> > > Signed-off-by: Akhil R <[email protected]>
> >> > > ---
> >> > >  .../devicetree/bindings/i3c/i3c.yaml          | 30 ++++++++++++++++---
> >> > >  1 file changed, 26 insertions(+), 4 deletions(-)
> >> > > 
> >> > > diff --git a/Documentation/devicetree/bindings/i3c/i3c.yaml b/Documentation/devicetree/bindings/i3c/i3c.yaml
> >> > > index e25fa72fd785..1705d90d4d79 100644
> >> > > --- a/Documentation/devicetree/bindings/i3c/i3c.yaml
> >> > > +++ b/Documentation/devicetree/bindings/i3c/i3c.yaml
> >> > > @@ -31,10 +31,12 @@ properties:
> >> > >        described in the device tree, which in turn means we have to describe
> >> > >        I3C devices.
> >> > >  
> >> > > -      Another use case for describing an I3C device in the device tree is when
> >> > > -      this I3C device has a static I2C address and we want to assign it a
> >> > > -      specific I3C dynamic address before the DAA takes place (so that other
> >> > > -      devices on the bus can't take this dynamic address).
> >> > > +      Other use-cases for describing an I3C device in the device tree are:
> >> > > +      - When the I3C device has a static I2C address and we want to assign
> >> > > +        it a specific I3C dynamic address before the DAA takes place (so
> >> > > +        that other devices on the bus can't take this dynamic address).
> >> > > +      - When the I3C device requires SETAASA for its discovery and uses a
> >> > > +        pre-defined static address.
> >> > >  
> >> > >    "#size-cells":
> >> > >      const: 0
> >> > > @@ -147,6 +149,26 @@ patternProperties:
> >> > >            through SETDASA. If static address is not present, this address is assigned
> >> > >            through SETNEWDA after assigning a temporary address via ENTDAA.
> >> > >  
> >> > > +      mipi-i3c-static-method:
> >> > > +        $ref: /schemas/types.yaml#/definitions/uint32
> >> > > +        minimum: 0x1
> >> > > +        maximum: 0xff
> >> > > +        default: 1
> >> > > +        description: |
> >> > > +          Bitmap describing which methods of Dynamic Address Assignment from a
> >> > > +          static address are supported by this I3C Target. A bit value of 1
> >> > > +          indicates support for that method, and 0 indicates lack of support.
> >> > 
> >> > I really am not keen on properties that are bitmaps, why can't we just
> >> > use the strings "setdasa", "setaasa" etc?
> >> 
> >> If this comes from a specification, then I'd tend to just copy it rather 
> >> than invent our own thing. Obviously if is something structured 
> >> fundamentally different from how DT is designed, then we wouldn't. But 
> >> this is just a simple property.
> >> 
> > 
> > The issue being that the specification is not public so it is difficult
> > to take any decision.
> 
> There is a public version available in the same link, but you would still
> have to provide them a name and an email ID. The document will be sent to
> the mail ID.
> 

The public version only contains one property:
mipi-disco-interface-revision


-- 
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com