Re: Re: [PATCH v1] fuse: enable large folios
Horst Birthelmer <[email protected]> Wed, 24 Jun 2026 08:10:54 +0200
| Newsgroups | dev.linux.lists.fuse-devel |
|---|---|
| Message-ID | <[email protected]> |
On Wed, Jun 24, 2026 at 12:34:16PM +0800, Jingbo Xu wrote: > > > On 6/24/26 9:21 AM, Joanne Koong wrote: > > Enable large folios, capping the max order at the largest request fuse > > can issue, so a folio always fits within a single request. The order > > range minimum is 0, so under memory pressure the allocator falls back to > > smaller folios. > > > > Benchmarks (libfuse passthrough_hp, buffered fio, single job, 4 GiB > > file, medians, NUMA-pinned, performance governor, strictlimiting on by > > default): > > > > tmpfs backing (page-cache bound): > > workload bs large folios off on delta > > seq read, cold, 128k 3110 MiB/s 4514 MiB/s +45% > > seq read, cold, 1M 3079 MiB/s 5181 MiB/s +68% > > seq read, warm, 128k 2438 MiB/s 4486 MiB/s +84% > > seq read, warm, 1M 2403 MiB/s 5123 MiB/s +113% > > writeback write, seq,128k 1211 MiB/s 1699 MiB/s +40% > > writeback write, seq, 1M 1462 MiB/s 2208 MiB/s +51% > > writeback write, rand,128k 1101 MiB/s 1757 MiB/s +60% + > > writeback write, rand, 1M 1284 MiB/s 2228 MiB/s +74% + > > > > xfs on NVMe backing (device bound for cold I/O): > > workload bs large folios off on delta > > seq read, cold, 128k 2030 MiB/s 2172 MiB/s +7% * > > seq read, cold, 1M 1999 MiB/s 2181 MiB/s +9% * > > seq read, warm, 128k 2451 MiB/s 4939 MiB/s +101% > > seq read, warm, 1M 2340 MiB/s 5639 MiB/s +141% > > writeback write, seq,128k 637 MiB/s 747 MiB/s +17% * > > writeback write, seq, 1M 694 MiB/s 833 MiB/s +20% * > > writeback write, rand,128k 1004 MiB/s 1648 MiB/s +64% + > > writeback write, rand, 1M 1171 MiB/s 2055 MiB/s +75% + > > > > (*) device-bandwidth bound. Not much throughput gain but system cpu > > utilization was roughly halved > > (+) random write was tested as an overwrite of a hot region (under > > writeback, this is page-cache bound, so the gain comes from lower > > per-folio cpu overhead rather than higher backing-device throughput) > > > > Random reads (4k and 128k) and writethrough writes were neutral with > > no regression (no read-modify-write or read-amplification penalty from > > large folios) > > > > More information about the benchmark setup and results are in > > https://github.com/joannekoong/linux/commits/fuse_large_folios_benchmarks/ > > > > Signed-off-by: Joanne Koong <[email protected]> > > --- > > This has a dependency on the iomap uptodate helpers that were submitted to > > Christian's vfs tree [1]. If it's easier to route this patch through > > Christian's tree, I can resubmit this. > > > > [1] https://lore.kernel.org/linux-fsdevel/[email protected]/ > > > > fs/fuse/file.c | 10 ++++++++++ > > 1 file changed, 10 insertions(+) > > > > diff --git a/fs/fuse/file.c b/fs/fuse/file.c > > index cb8da4c06d17..3c9be6d8ede1 100644 > > --- a/fs/fuse/file.c > > +++ b/fs/fuse/file.c > > @@ -3136,4 +3136,14 @@ void fuse_init_file_inode(struct inode *inode, unsigned int flags) > > > > if (IS_ENABLED(CONFIG_FUSE_DAX)) > > fuse_dax_inode_init(inode, flags); > > + > > + if (!FUSE_IS_DAX(inode)) { > > + unsigned int max_pages = min(min(fc->max_write, > > + fc->max_read) >> PAGE_SHIFT, > > + fc->max_pages); > > + > > + if (max_pages) > > + mapping_set_folio_order_range(inode->i_mapping, 0, > > + ilog2(max_pages)); > > + } > > } > > mapping_set_folio_order_range(..., 0, 0) seems harmless even when > max_pages is 0. > > Anyway > > Reviewed-by: Jingbo Xu \<[email protected]\> > I was just about to suggest something like mapping_set_folio_order_range(inode->i_mapping, 0, ilog2(max_pages ?: 1)); but you are right, it's not a problem. > > -- > Thanks, > Jingbo > This was actually one of the problems I ran into when I enabled large folios in linux 6.17. Since it would create problems for readahead. Reviewed-By: Horst Birthelmer <[email protected]> --- Thanks, Horst