Re: [PATCH v2] PCI: dwc: Add suspend_poweroff flag for platforms with RC power loss

On Fri, Jul 17, 2026 at 03:41:21PM +0800, [email protected] wrote:
> From: Richard Zhu <[email protected]>
> 
> Some platforms like i.MX power off their PCIe RC controllers during
> system suspend, requiring full re-initialization on resume. These
> platforms need to enter L2 state to properly notify endpoints before
> power loss.
> 
> According to PCIe base spec r7.0, sec 5.2, the system software should
> transition the device into D3Hot before broadcasting the PME_Turn_Off
> message to initiate L2 entry. However, some endpoint devices fail the
> D3cold capability check in pci_host_common_d3cold_possible(), which
> would normally prevent L2 entry.

Wakeup devices that don't support PME from D3cold will fail the D3cold
capability check, but I don't think those are the problem you're
solving.

This appears to handle devices that are not in D3hot, and that's not a
property of the endpoint; it's a property of its driver.  Is the
problem here that some driver didn't put its device in D3hot?

> For platforms where the RC loses power during suspend, L2 entry is
> essential regardless of D3cold support, as the link will be lost anyway.
> Add a suspend_poweroff flag to force L2 entry in such cases, and enable
> it for i.MX PCIe controllers.
> 
> Note: This violates the spec requirement that devices be in D3Hot before
> PME_Turn_Off, but is necessary for proper operation on platforms with RC
> power loss during suspend.

If the device isn't in D3hot, it may still be active, and I think the
PME_Turn_Off will abort any DMAs in progress, which doesn't sound like
proper operation of the endpoint.

> Signed-off-by: Richard Zhu <[email protected]>
> ---
> Changes in v2:
> - Rename the new added flag.
> - Update commit description and comments.
> 
> ---
>  drivers/pci/controller/dwc/pci-imx6.c             | 11 +++++++++++
>  drivers/pci/controller/dwc/pcie-designware-host.c | 10 ++++++++--
>  drivers/pci/controller/dwc/pcie-designware.h      |  8 ++++++++
>  3 files changed, 27 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
> index 98e1db751132a..5a43bf396521b 100644
> --- a/drivers/pci/controller/dwc/pci-imx6.c
> +++ b/drivers/pci/controller/dwc/pci-imx6.c
> @@ -1957,6 +1957,17 @@ static int imx_pcie_probe(struct platform_device *pdev)
>  		 */
>  		imx_pcie_add_lut_by_rid(imx_pcie, 0);
>  	} else {
> +		/*
> +		 * i.MX RC is powered off during suspend, requiring L2 entry
> +		 * to notify endpoints before power loss. Some endpoints fail
> +		 * the D3cold capability check, which would normally prevent
> +		 * L2 entry. Force L2 entry anyway since the link will be lost
> +		 * when RC powers off.
> +		 *
> +		 * Note: Per PCIe spec r7.0 sec 5.2, devices should be in D3Hot
> +		 * before PME_Turn_Off. This may not be guaranteed here.
> +		 */
> +		pci->pp.suspend_poweroff = true;
>  		if (imx_check_flag(imx_pcie, IMX_PCIE_FLAG_SKIP_L23_READY))
>  			pci->pp.skip_l23_ready = true;
>  		if (imx_check_flag(imx_pcie, IMX_PCIE_FLAG_KEEP_MSI_CAP))
> diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
> index 06722259d2e37..95a31d65e1ca9 100644
> --- a/drivers/pci/controller/dwc/pcie-designware-host.c
> +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
> @@ -1222,14 +1222,20 @@ static int dw_pcie_pme_turn_off(struct dw_pcie *pci)
>  
>  int dw_pcie_suspend_noirq(struct dw_pcie *pci)
>  {
> -	bool pme_capable = false;
> +	bool d3cold, pme_capable = false;
>  	int ret = 0;
>  	u32 val;
>  
>  	if (!dw_pcie_link_up(pci))
>  		goto stop_link;
>  
> -	if (!pci_host_common_d3cold_possible(pci->pp.bridge, &pme_capable))
> +	d3cold = pci_host_common_d3cold_possible(pci->pp.bridge, &pme_capable);
> +	/*
> +	 * Enter L2 if D3cold is possible, or if the platform loses RC power
> +	 * during suspend (in which case L2 entry is required to notify
> +	 * endpoints before power loss, regardless of D3cold support).
> +	 */
> +	if (!d3cold && !pci->pp.suspend_poweroff)
>  		return 0;
>  
>  	if (pci->pp.ops->pme_turn_off) {
> diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
> index de4b245b1758c..3ce7d30d9a4d5 100644
> --- a/drivers/pci/controller/dwc/pcie-designware.h
> +++ b/drivers/pci/controller/dwc/pcie-designware.h
> @@ -471,6 +471,14 @@ struct dw_pcie_rp {
>  	bool			native_ecam;
>  	bool                    skip_l23_ready;
>  	bool			skip_pwrctrl_off;
> +	/*
> +	 * suspend_poweroff: Force L2 entry during suspend even when D3cold
> +	 * capability check fails. Used on platforms where RC loses power
> +	 * during suspend and must notify endpoints via L2 entry before
> +	 * power loss. May not meet PCIe spec requirement for devices to be
> +	 * in D3Hot before PME_Turn_Off.
> +	 */
> +	bool                    suspend_poweroff;
>  };
>  
>  struct dw_pcie_ep_ops {
> -- 
> 2.34.1
>