Re: [PATCH V7] Bluetooth: btnxpuart: Add M.2 Bluetooth device support using pwrseq

Hi Luiz,

Gentle ping ...

On Tue, Jul 21, 2026 at 11:04:58AM +0800, Sherry Sun (OSS) wrote:
>From: Sherry Sun <[email protected]>
>
>Power supply to the M.2 Bluetooth device attached to the host using M.2
>connector is controlled using the 'uart' pwrseq device. So add support
>for getting the pwrseq device if the OF graph link is present.
>
>Once obtained, pwrseq_power_on() is called to power up the M.2 Bluetooth
>card. The power sequencer descriptor is obtained via pwrseq_get() with
>the UART controller device (serdev->ctrl->dev), since the OF graph
>link is defined on the UART controller node.
>
>Also add the explicit pwrseq_put() call in all exit paths, pwrseq_put()
>already calls pwrseq_power_off() internally, so no separate
>pwrseq_power_off() call is needed.
>
>Signed-off-by: Sherry Sun <[email protected]>
>Reviewed-by: Bartosz Golaszewski <[email protected]>
>Reviewed-by: Frank Li <[email protected]>
>Reviewed-by: Manivannan Sadhasivam <[email protected]>
>---
>Changes in V7:
>1. Seperate this Bluetooth patch from the V6 M.2 patch set so that it
>can be applied directly to bluetooth-next tree, no code change.
>https://lore.kernel.org/all/[email protected]/
>---
> drivers/bluetooth/btnxpuart.c | 34 ++++++++++++++++++++++++++++++----
> 1 file changed, 30 insertions(+), 4 deletions(-)
>
>diff --git a/drivers/bluetooth/btnxpuart.c b/drivers/bluetooth/btnxpuart.c
>index 0bb300eef157..81a11ac05114 100644
>--- a/drivers/bluetooth/btnxpuart.c
>+++ b/drivers/bluetooth/btnxpuart.c
>@@ -9,6 +9,8 @@
>
> #include <linux/serdev.h>
> #include <linux/of.h>
>+#include <linux/of_graph.h>
>+#include <linux/pwrseq/consumer.h>
> #include <linux/skbuff.h>
> #include <linux/unaligned.h>
> #include <linux/firmware.h>
>@@ -211,6 +213,7 @@ struct btnxpuart_dev {
>
> 	struct ps_data psdata;
> 	struct btnxpuart_data *nxp_data;
>+	struct pwrseq_desc *pwrseq;
> 	struct reset_control *pdn;
> 	struct hci_uart hu;
> };
>@@ -1872,11 +1875,26 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
> 		return err;
> 	}
>
>+	if (of_graph_is_present(dev_of_node(&serdev->ctrl->dev))) {
>+		struct pwrseq_desc *pwrseq;
>+
>+		pwrseq = pwrseq_get(&serdev->ctrl->dev, "uart");
>+		if (IS_ERR(pwrseq))
>+			return dev_err_probe(&serdev->dev, PTR_ERR(pwrseq),
>+					     "failed to get pwrseq\n");
>+
>+		nxpdev->pwrseq = pwrseq;
>+		err = pwrseq_power_on(pwrseq);
>+		if (err)
>+			goto err_pwrseq_put;
>+	}
>+
> 	/* Initialize and register HCI device */
> 	hdev = hci_alloc_dev();
> 	if (!hdev) {
> 		dev_err(&serdev->dev, "Can't allocate HCI device\n");
>-		return -ENOMEM;
>+		err = -ENOMEM;
>+		goto err_pwrseq_put;
> 	}
>
> 	reset_control_deassert(nxpdev->pdn);
>@@ -1907,13 +1925,16 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
> 	if (bacmp(&ba, BDADDR_ANY))
> 		hci_set_quirk(hdev, HCI_QUIRK_USE_BDADDR_PROPERTY);
>
>-	if (hci_register_dev(hdev) < 0) {
>+	err = hci_register_dev(hdev);
>+	if (err < 0) {
> 		dev_err(&serdev->dev, "Can't register HCI device\n");
> 		goto probe_fail;
> 	}
>
>-	if (ps_setup(hdev))
>+	if (ps_setup(hdev)) {
>+		err = -ENODEV;
> 		goto probe_fail_unregister;
>+	}
>
> 	hci_devcd_register(hdev, nxp_coredump, nxp_coredump_hdr,
> 			   nxp_coredump_notify);
>@@ -1925,7 +1946,10 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
> probe_fail:
> 	reset_control_assert(nxpdev->pdn);
> 	hci_free_dev(hdev);
>-	return -ENODEV;
>+err_pwrseq_put:
>+	if (nxpdev->pwrseq)
>+		pwrseq_put(nxpdev->pwrseq);
>+	return err;
> }
>
> static void nxp_serdev_remove(struct serdev_device *serdev)
>@@ -1952,6 +1976,8 @@ static void nxp_serdev_remove(struct serdev_device *serdev)
> 	ps_cleanup(nxpdev);
> 	hci_unregister_dev(hdev);
> 	reset_control_assert(nxpdev->pdn);
>+	if (nxpdev->pwrseq)
>+		pwrseq_put(nxpdev->pwrseq);
> 	hci_free_dev(hdev);
> }
>
>
>base-commit: 3fe08b9796f36ef437ab9328e7dd1e5ff2d66603
>-- 
>2.50.1
>