[PATCH v7 2/5] arm64: dts: qcom: shikra: Add CCI definitions
Nihal Kumar Gupta <[email protected]>
| Newsgroups | dev.linux.lists.imx,org.infradead.lists.linux-arm-kernel,org.kernel.vger.linux-arm-msm,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-i2c,org.kernel.vger.linux-kernel,org.kernel.vger.linux-media |
|---|---|
| Message-ID | <[email protected]> |
Qualcomm Shikra SoC has one Camera Control Interface (CCI) containing two I2C hosts. Reviewed-by: Bryan O'Donoghue <[email protected]> Reviewed-by: Vladimir Zapolskiy <[email protected]> Reviewed-by: Loic Poulain <[email protected]> Signed-off-by: Nihal Kumar Gupta <[email protected]> --- arch/arm64/boot/dts/qcom/shikra.dtsi | 69 ++++++++++++++++++++++++++++++++++++ 1 file changed, 69 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/shikra.dtsi b/arch/arm64/boot/dts/qcom/shikra.dtsi index 44e1a333e97f1c88a672c77579fbe987d4285693..ce5887b9b1d4a186fe967779b9615ab4e4727ff8 100644 --- a/arch/arm64/boot/dts/qcom/shikra.dtsi +++ b/arch/arm64/boot/dts/qcom/shikra.dtsi @@ -795,6 +795,38 @@ qup_uart9_default: qup-uart9-default-state { bias-disable; }; + cci_i2c0_default: cci-i2c0-default-state { + /* SDA, SCL */ + pins = "gpio36", "gpio37"; + function = "cci_i2c0"; + drive-strength = <2>; + bias-pull-up; + }; + + cci_i2c0_sleep: cci-i2c0-sleep-state { + /* SDA, SCL */ + pins = "gpio36", "gpio37"; + function = "cci_i2c0"; + drive-strength = <2>; + bias-pull-down; + }; + + cci_i2c1_default: cci-i2c1-default-state { + /* SDA, SCL */ + pins = "gpio41", "gpio42"; + function = "cci_i2c1"; + drive-strength = <2>; + bias-pull-up; + }; + + cci_i2c1_sleep: cci-i2c1-sleep-state { + /* SDA, SCL */ + pins = "gpio41", "gpio42"; + function = "cci_i2c1"; + drive-strength = <2>; + bias-pull-down; + }; + sdc1_state_on: sdc1-on-state { clk-pins { pins = "sdc1_clk"; @@ -1928,6 +1960,43 @@ port@1 { }; }; + cci: cci@5c1b000 { + compatible = "qcom,shikra-cci", "qcom,msm8996-cci"; + reg = <0x0 0x05c1b000 0x0 0x1000>; + + interrupts = <GIC_SPI 206 IRQ_TYPE_EDGE_RISING 0>; + + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_CCI_0_CLK>; + clock-names = "ahb", + "cci"; + + power-domains = <&gcc GCC_CAMSS_TOP_GDSC>; + + pinctrl-0 = <&cci_i2c0_default &cci_i2c1_default>; + pinctrl-1 = <&cci_i2c0_sleep &cci_i2c1_sleep>; + pinctrl-names = "default", "sleep"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + + cci_i2c0: i2c-bus@0 { + reg = <0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + + cci_i2c1: i2c-bus@1 { + reg = <1>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + remoteproc_mpss: remoteproc@6080000 { compatible = "qcom,shikra-mpss-pas"; reg = <0x0 0x06080000 0x0 0x100>; -- 2.34.1