[PATCH v9 00/61] Add HDMI 2.0 support to DW HDMI QP TX
Cristian Ciocaltea <[email protected]>
| Newsgroups | dev.linux.lists.linux-sunxi,org.freedesktop.lists.dri-devel,org.infradead.lists.linux-arm-kernel,org.infradead.lists.linux-rockchip,org.kernel.vger.linux-kernel |
|---|---|
| Message-ID | <[email protected]> |
Enable HDMI 2.0 display modes (e.g. 4K@60Hz) on the Synopsys DW HDMI QP
TX controller, as found in Rockchip RK3576 & RK3588 SoCs, by adding SCDC
management for high TMDS clock ratio and scrambling. Since SCDC state
is lost on sink disconnects, the bridge driver needs to trigger a CRTC
reset during connector detection.
To support this at the DRM infrastructure level, the series first
introduces the HDMI version enum, then prepares for changing the
signature of drmm_connector_hdmi_init(), i.e. dropping the vendor,
product, supported_formats and max_bpc arguments, which are being moved
into struct drm_connector_hdmi_funcs, by temporarily renaming the helper
to drmm_connector_hdmi_ini2(). This lets the new signature be
introduced under the original name while callers are converted
incrementally. Note the transitional name matches the original's length
so continuation-line arguments stay aligned to the opening parenthesis,
keeping the diff to the identifier itself and avoiding re-alignment
churn.
Appending more HDMI-specific arguments to the init function would not
scale well, hence the hdmi_funcs struct is extended with new fields:
supported_hdmi_ver, supported_tmds_char_rate. These are used to
infer and/or limit the maximum TMDS character rate permitted for the
connector.
Patches 5-10 build the connector and bridge scrambling infrastructure on
top: the connector scrambler callbacks/flags, the scdc-helper
additions (connector-prefixed debug macro and SCDC version helper), and
the HDMI scrambling management helpers including SCDC source-version
advertisement.
Patches 11-18 wires this up through the hdmi-state-helper and bridge
connector layers: source TMDS rate validation, hotplug SCDC state sync
and the scrambling requirement, new source-side scrambling bridge ops,
the switch to a cached-status, atomic-aware .detect_ctx() connector
helper, and finally hooking up the HDMI 2.0 scrambler callbacks.
The SCDC scrambling feature itself is implemented in the DW HDMI QP
bridge driver, alongside i2c error-message rate limiting,
.enable_hpd()/.disable_hpd() PHY ops and a dw_hdmi_qp_hpd_notify()
helper (patches 19-23).
Patches 24-32 cover the Rockchip platform driver and HPD handling: minor
cleanups (newlines in dev_err_probe(), consistent local dev variable,
dropping unnecessary include/define), avoiding spurious HDP IRQ wakeups,
masking the RK3576 HPD IRQ in io_init, implementing the
.{enable|disable}_hpd() PHY ops, switching HPD reports to
dw_hdmi_qp_hpd_notify() to restrict events to the affected connector,
and dropping the now-unused .setup_hpd() PHY op.
Patches 34-39 convert VC4 HDMI to the common infrastructure as a proof
of reuse: adopting the shared TMDS char rate constants, switching to
drm_hdmi_mode_needs_scrambling(), proper -EDEADLK handling, and
replacing the driver-local scrambling implementation with the common
SCDC scrambling helpers.
Patches 40-47 advertise supported version for all HDMI
connectors/bridges, except the MediaTek HDMI driver (for now), as it
requires non-trivial changes: there's a core library shared between two
drivers, one being HDMI 2.0 compliant.
Patches 48-57 add KUnit tests: HDMI caps-based init coverage and
source-side scrambler validation for the connector, conversion of
hdmi_state_helper to the new drmm_connector_hdmi_init() with
max_tmds_char_rate validation, a new 4K@60Hz 600MHz TMDS EDID,
source-side scrambling decision coverage, and conformity fixes for the
existing 1080p+4K YUV420 200MHz and 4K RGB/YUV 340MHz test EDID blobs.
Eventually patches 58-61 remove the now unused
drmm_connector_hdmi_ini2() helper and drop redundant hdmi fields from
connector structs: vendor, product, supported_formats and max_bpc.
This has been tested on the following boards:
* Radxa ROCK 5B (RK3588)
* Radxa ROCK 4D (RK3576)
* Raspberry Pi 5 Model B Rev 1.1 (BCM2712 D0)
Note that commit d87773de9efe1 ("clocksource/drivers/arm_arch_timer:
Default to EL2 virtual timer when running VHE"), introduced in v7.2-rc1,
causes Raspberry Pi 5 to hang during boot. Reverting the commit
restores normal boot. This issue has already been reported in [1];
alternatively, the workaround proposed in [2] can be applied.
Regards,
Cristian
[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/[email protected]/
Signed-off-by: Cristian Ciocaltea <[email protected]>
---
Changes in v9:
- Collected A-b, R-b, T-b tags from Dmitry, Maxime, Maud
- Dropped misleading "HDMI_VERSION_UNKNOWN means legacy/default
behaviour" from drm_connector_hdmi_caps.supported_hdmi_ver
documentation
- Warned in drm_bridge_add() if an HDMI bridge leaves supported_hdmi_ver
unset
- Added max_tmds_char_rate to drm_bridge struct and wire it through
drm_bridge_connector_init() along with supported_hdmi_ver
- Got rid of connector's scrambler_supported flag and, instead, relied
on checking the presence of scrambler callbacks via a new
drm_connector_hdmi_scrambler_supported() helper (Dmitry)
- Dropped HDMI connector scdc_cb callback and introduced
scdc_work_initialized flag to perform lazy initialization and guard
the teardown paths against touching an uninitialized work item
- Unconditionally checked connector->hdmi.max_tmds_char_rate in
"drm/display: hdmi-state-helper: Add fallback TMDS rate validation"
and performed s/fallback/source/ in commit subject & description
(Maxime)
- Added a TODO comment for checking
drm_display_info.hdmi.scdc.scrambling.low_rates in "drm/display:
hdmi-state-helper: Set HDMI scrambling requirement" patch (Maxime)
- Moved the prototype changes from "drm/display: hdmi-state-helper: Sync
SCDC state on hotplug" into a dedicated "drm/display:
hdmi-state-helper: Pass acquire ctx to hotplug helpers" patch; also
switched ctx and status args ordering, for consistency with
detect_ctx() signature (Maxime)
- Ensured HDMI connector's SCDC delayed work is explicitly canceled
during connector cleanup (Sashiko)
- Fixed a potential NULL pointer dereference in
drm_connector_hdmi_enable_scrambling() and
drm_connector_hdmi_sync_scdc() helpers caused by forcing an EDID
advertising SCDC on a connector that physically lacks an I2C DDC bus
(Sashiko)
- dw-hdmi-qp
* Fixed a potential NULL pointer dereference in
dw_hdmi_qp_hpd_notify() helper by using a local variable to cache
the connector pointer (Sashiko)
* Ensured hdmi->phy.ops->disable() is not skipped in
dw_hdmi_qp_bridge_atomic_disable() by accessing the connector via
drm_atomic_get_old_connector_for_encoder() instead of
hdmi->curr_conn (Sashiko)
* Mitigated a potential use-after-free reported by Sashiko caused when
HPD interrupt fires after the DRM device is torn down; reworked
"Defer HPD IRQ enable until after connector setup" into:
* Factor out HPD interrupt mask/unmask helpers
* Control the HPD IRQ line via the bridge HPD ops
* Added new patch addressing another Sashiko finding: drm/rockchip:
dw_hdmi_qp: Avoid spurious HPD IRQ thread wakeups
* Added new patch: drm/bridge: dw-hdmi-qp: Remove unused workqueue
include and define
* Dropped .hdmi_tmds_char_rate_valid() usage from the
bridge/synopsys/dw-hdmi-qp.c scrambling support patch, while
advertising HDMI 1.4 capability for no-hpd configurations
- VC4
* Passed ctx instead of NULL when calling
drm_atomic_helper_connector_hdmi_hotplug() from
vc4_hdmi_handle_hotplug() in the helper preparatory patch
* Aligned with the expected detect_ctx() semantics in a dedicated
"drm/vc4: hdmi: Propagate -EDEADLK to the top level" rather than
bundled in the conversion patch
* Optimized diff around drm_dev_enter() in the conversion patch
(Maxime)
* Simplified vc4_hdmi_connector_clock_valid() logic by deferring max
clock validation to HDMI helpers (new patch)
- Migrated to a funcs-based HDMI connector init API - new patches:
* drm/display: hdmi: Rename drmm_connector_hdmi_init() to *_ini2()
* drm/display: bridge_connector: Convert to drmm_connector_hdmi_init()
* drm/vc4: hdmi: Convert to drmm_connector_hdmi_init()
* drm/vc4: hdmi: Convert to common HDMI 2.0 scrambling infrastructure
* drm/sun4i: hdmi: Convert to drmm_connector_hdmi_init()
* drm/tests: connector: Convert to drmm_connector_hdmi_init()
* drm/tests: hdmi_state_helper: Convert to drmm_connector_hdmi_init()
* drm/bridge: adv7511: Advertise HDMI 1.2 capabilities
* drm/bridge: inno-hdmi: Advertise HDMI 1.2 capabilities
* drm/bridge: ite-it6263: Drop redundant .mode_valid hook
* drm/bridge: ite-it6263: Advertise HDMI 1.3 capabilities
* drm/bridge: ite-it66121: Advertise HDMI 1.2 capabilities
* drm/bridge: lontium-lt9611: Advertise HDMI 1.4 capabilities
* drm/rockchip: rk3066_hdmi: Advertise HDMI 1.4 capabilities
* drm/sun4i: hdmi: Convert to drmm_connector_hdmi_init()
* drm/connector: Remove drmm_connector_hdmi_ini2()
* drm/connector: Drop redundant hdmi vendor/product fields
* drm/connector: Drop redundant hdmi supported_formats field
* drm/connector: Drop redundant max_bpc field
- KUnit
* Adapted hdmi_state_helper scrambler tests and reworked a couple of
max_tmds_char_rate tests according to the latest DRM core changes
* Fixed a regression in the HDMI caps-based init coverage
* Fix a couple of bisectability issues, also implied partial commit
reorder
* Set supported HDMI version for the test bridges (new patch)
- Rebased series onto latest drm-misc-next and removed "drm/rockchip:
dw_hdmi_qp: Drop unnecessary #include" patch, since a similar change
as been already applied
- Link to v8: https://patch.msgid.link/[email protected]
Changes in v8:
- Added an enum hdmi_version under video/hdmi to describe the HDMI
specification version a source/sink supports (new patch 1)
- Introduced HDMI connector capabilities API and reworked the
infrastructure patches on top of it: drmm_connector_hdmi_init() now
takes a drm_connector_hdmi_caps struct that carries supported_formats,
max_bpc, supported_hdmi_ver and max_tmds_char_rate (new patches 2-3)
- Moved all the new SCDC helpers covering both source and sink to
display/drm_hdmi_helper.c
- Renamed drm_scdc_{start,stop}_scrambling() to
drm_connector_hdmi_{enable,disable}_scrambling() and added a
connector-state argument so the scrambler_needed flag is checked
centrally instead of in every driver
- Renamed drm_scdc_sync_status() to drm_connector_hdmi_sync_scdc(),
aligned its lifecycle with vc4_hdmi_reset_link(), and removed the
internal drm_scdc_reset_crtc() helper; it now also gates on CRTC state
and an in-flight commit (Maxime)
- Changed the prototype of drm_atomic_helper_connector_hdmi_hotplug() to
take an acquire context and an int return, instead of adding a new
_ctx variant (Maxime)
- Added drm_hdmi_mode_needs_scrambling() to centralise the above-340 MHz
decision (new patch 7)
- Made SCDC source version negotiation optional and moved it to a
dedicated patch "drm/display: hdmi: Advertise SCDC source version when
scrambling" (new patch 8), backed by a new
drm_scdc_set_source_version() helper in "drm/display: scdc-helper: Add
helper to set SCDC version information" (new patch 6)
- Added a fallback TMDS rate validation patch using the connector-level
max_tmds_char_rate when the driver provides no .tmds_char_rate_valid()
hook (new patch 9)
- Split scrambler_needed flag handling into its own hdmi-state-helper
dedicate change (new patch 11)
- VC4:
* Replaced vc4_hdmi_mode_needs_scrambling() with
drm_hdmi_mode_needs_scrambling() (new patch 30)
* Restored drm_dev_{enter,exit}() pairing around the converted
scrambling paths
* Removed now unused output_{bpc,color_format} fields from vc4_hdmi as
part of the SCDC conversion
- KUnit:
* Covered the caps-based connector init path: NULL caps, inferred
max_tmds_char_rate per supported_hdmi_ver, and override validation
(new patch 32)
* Switched drm_hdmi_state_helper_test to the caps-based init helper
and exposed it through
drm_kunit_helper_connector_hdmi_init_with_caps_edid_funcs() (new
patch 34)
* Added max_tmds_char_rate fallback coverage in
drm_hdmi_state_helper_test (new patch 35)
- Rebased onto latest drm-misc-next and dropped the already applied
"drm/fb-helper: Remove unused local variable in hotplug_event()" patch
- Link to v7: https://patch.msgid.link/[email protected]
Changes in v7:
- Split the scrambler_needed flag computation from the SCDC scrambling
helpers into a standalone hdmi_state_helper patch for clarity (new
patch 6)
- Added vc4 HDMI conversion to common TMDS char rate constants and SCDC
scrambling helpers as a proof of reuse (new patches 24-25)
- Added KUnit tests for connector scrambler_supported/callback
consistency validation (new patch 26)
- Added 4K@60Hz 600MHz TMDS test EDID for high-rate scrambling coverage
(new patch 27)
- Added KUnit tests for hdmi_state_helper scrambler_needed flag:
low-rate, high-rate, and source-no-support cases (new patch 28)
- Fixed EDID conformity issues (edid-decode v1.33.0 failures) in the
existing 1080p+4K YUV420 200MHz and 4K RGB/YUV 340MHz test EDIDs
without changing the capabilities used by existing tests (new patches
29-30)
- Rebased onto latest drm-misc-next
- Link to v6: https://patch.msgid.link/[email protected]
Changes in v6:
- Collected R-b & A-b tags from Dmitry and Heiko
- Restructured the series from 10 into 22 patches, splitting the SCDC
scrambling helpers, connector infrastructure, bridge operations,
bridge_connector plumbing, dw-hdmi-qp implementation, and Rockchip
platform changes into distinct commits
- Added drm_scdc_dbg() macro to simplify debug messages (new patch)
- Added drm_scdc_start/stop/sync_status() helpers for full scrambling
lifecycle management (reworked from v5 patch 5)
- Added drm_atomic_helper_connector_hdmi_hotplug_ctx() to propagate
modeset acquire context for SCDC sync on hotplug (new patch)
- Added connector scrambler callbacks and SCDC work/flag infrastructure
as a separate patch (split from v5 patch 5)
- Added DRM_BRIDGE_OP_HDMI_SCRAMBLER bridge operation with
hdmi_scrambler_enable/disable callbacks (new patch)
- Implemented bridge_connector scrambler interface wiring (new patch)
- Added .enable_hpd()/.disable_hpd() PHY ops for dw-hdmi-qp bridge and
Rockchip platform drivers, replacing the obsolete .setup_hpd() op
- Added dw_hdmi_qp_hpd_notify() helper for targeted connector-only HPD
notification (split from v5 patch 10)
- Dropped drm_fb_helper_hotplug_event() unused variable (new cleanup)
- Dropped unused drm_simple_kms_helper.h include (new cleanup)
- Masked RK3576 HPD IRQ in io_init() for consistency with RK3588
- Rebased onto latest drm-misc-next
- Link to v5: https://patch.msgid.link/[email protected]
Changes in v5:
- Added new patches: 1/10, 3/10, 6/10, 7/10, 8/10
- Removed redundant no-op error check in drm_bridge_helper_reset_crtc()
(patch 1)
- Removed the EDEADLK retry loop from the bridge .detect_ctx() callback,
as that's already handled in the drm_bridge_detect_ctx() helper or by
the caller when ctx is provided (patch 2)
- Refactored drm_bridge_detect() to delegate to drm_bridge_detect_ctx()
and added a WARN_ON for unexpected negative return values (patch 2)
- Split the bridge-connector .detect_ctx() switch into a preparatory
patch to use cached connector status in .get_modes() (patch 3)
- Improved error handling in SCDC scrambling setup: roll back high TMDS
clock ratio on scrambling failure, reset scramb_enabled flag on
set_scramb failure, and add SCDC version read/write error checks
(patch 5)
- Annotated scramb_enabled with READ_ONCE/WRITE_ONCE for cross-context
access between modeset paths and the scrambling work item (patch 5)
- Renamed SCDC_MIN_SOURCE_VERSION to SCDC_MAX_SOURCE_VERSION (patch 5)
- Rate limited i2c error messages (patch 6)
- Added missing newlines in dev_err_probe() messages (patch 7)
- Replaced indirect device pointer accesses with local dev variable in
bind() (patch 8)
- Split the HPD connector restriction (formerly patch 4/4): register HPD
IRQ after connector setup first (patch 9), then restrict HPD event to
the affected connector (patch 10); also collected R-b from Heiko
- Rebased onto latest drm-misc-next
- Link to v4: https://lore.kernel.org/r/[email protected]
Changes in v4:
- Fixed conflicts while rebasing onto latest drm-misc-next
- Link to v3: https://lore.kernel.org/r/[email protected]
Changes in v3:
- Used drm_bridge_helper_reset_crtc() helper to reset the display
pipeline and got rid of some boilerplate code (Maxime)
- Rebased onto latest drm-misc-next
- Link to v2: https://lore.kernel.org/r/[email protected]
Changes in v2:
- Collected Tested-by tags from Diederik and Maud
- Rebased onto latest drm-misc-next
- Ensured the recently introduced 'no-hpd' support for dealing with
unconnected/repurposed/broken HPD pin is limited to HDMI 1.4 rates
- Link to v1: https://lore.kernel.org/r/[email protected]
---
Cristian Ciocaltea (61):
video/hdmi: Introduce HDMI version enum
drm/display: hdmi: Rename drmm_connector_hdmi_init() to *_ini2()
drm/connector: Add drmm_connector_hdmi_init() with new signature
drm/display: bridge_connector: Convert to drmm_connector_hdmi_init()
drm/connector: Add HDMI 2.0 scrambler infrastructure
drm/display: scdc-helper: Add macro for connector-prefixed debug messages
drm/display: scdc-helper: Add helper to set SCDC version information
drm/display: hdmi: Add HDMI 2.0 scrambling management helpers
drm/display: hdmi: Advertise SCDC source version when scrambling
drm/bridge: Remove redundant error check in drm_bridge_helper_reset_crtc()
drm/bridge: Add bridge ops for source-side HDMI 2.0 scrambling
drm/display: bridge_connector: Use cached connector status in .get_modes()
drm/display: bridge_connector: Switch to .detect_ctx() connector helper
drm/display: bridge_connector: Wire up HDMI 2.0 scrambler callbacks
drm/display: hdmi-state-helper: Add source TMDS rate validation
drm/display: hdmi-state-helper: Pass acquire ctx to hotplug helpers
drm/display: hdmi-state-helper: Sync SCDC state on hotplug
drm/display: hdmi-state-helper: Set HDMI scrambling requirement
drm/bridge: dw-hdmi-qp: Rate limit i2c read error messages
drm/bridge: dw-hdmi-qp: Provide .{enable,disable}_hpd() PHY ops
drm/bridge: dw-hdmi-qp: Remove unused workqueue include and define
drm/bridge: dw-hdmi-qp: Add HDMI 2.0 scrambling support
drm/bridge: dw-hdmi-qp: Provide dw_hdmi_qp_hpd_notify() helper
drm/rockchip: dw_hdmi_qp: Fix NULL deref in PM ops on incomplete bind
drm/rockchip: dw_hdmi_qp: Add missing newlines in dev_err_probe() messages
drm/rockchip: dw_hdmi_qp: Use local dev variable consistently in bind()
drm/rockchip: dw_hdmi_qp: Avoid spurious HPD IRQ thread wakeups
drm/rockchip: dw_hdmi_qp: Mask RK3576 HPD IRQ in io_init
drm/rockchip: dw_hdmi_qp: Implement .{enable,disable}_hpd() PHY ops
drm/rockchip: dw_hdmi_qp: Factor out HPD interrupt (un)mask helpers
drm/rockchip: dw_hdmi_qp: Control the HPD IRQ line via the bridge HPD ops
drm/rockchip: dw_hdmi_qp: Use dw_hdmi_qp_hpd_notify() for HPD reports
drm/bridge: dw-hdmi-qp: Drop unused .setup_hpd() phy op
drm/vc4: hdmi: Use common TMDS char rate constants
drm/vc4: hdmi: Switch to drm_hdmi_mode_needs_scrambling()
drm/vc4: hdmi: Propagate -EDEADLK to the top level
drm/vc4: hdmi: Convert to drmm_connector_hdmi_init()
drm/vc4: hdmi: Convert to common HDMI 2.0 scrambling infrastructure
drm/vc4: hdmi: Defer pixel clock validation to HDMI helpers
drm/bridge: adv7511: Advertise HDMI 1.2 capabilities
drm/bridge: inno-hdmi: Advertise HDMI 1.2 capabilities
drm/bridge: ite-it6263: Drop redundant .mode_valid hook
drm/bridge: ite-it6263: Advertise HDMI 1.3 capabilities
drm/bridge: ite-it66121: Advertise HDMI 1.2 capabilities
drm/bridge: lontium-lt9611: Advertise HDMI 1.4 capabilities
drm/rockchip: rk3066_hdmi: Advertise HDMI 1.4 capabilities
drm/sun4i: hdmi: Convert to drmm_connector_hdmi_init()
drm/tests: edid: Add 4K@60Hz EDID with 600MHz TMDS
drm/tests: edid: Fix conformity for 1080p+4K YUV420 200MHz EDID
drm/tests: edid: Fix conformity for 4K RGB/YUV 340MHz EDID
drm/tests: bridge: Set supported HDMI version
drm/tests: connector: Convert to drmm_connector_hdmi_init()
drm/tests: connector: Add HDMI max_tmds_char_rate init coverage
drm/tests: connector: Add HDMI source-side scrambler coverage
drm/tests: hdmi_state_helper: Convert to drmm_connector_hdmi_init()
drm/tests: hdmi_state_helper: Add connector-provided max_tmds_char_rate coverage
drm/tests: hdmi_state_helper: Cover source-side scrambling decision
drm/connector: Remove drmm_connector_hdmi_ini2()
drm/connector: Drop redundant hdmi vendor/product fields
drm/connector: Drop redundant hdmi supported_formats field
drm/connector: Drop redundant max_bpc field
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 22 +-
drivers/gpu/drm/bridge/inno-hdmi.c | 1 +
drivers/gpu/drm/bridge/ite-it6263.c | 33 +-
drivers/gpu/drm/bridge/ite-it66121.c | 13 +-
drivers/gpu/drm/bridge/lontium-lt9611.c | 16 +-
drivers/gpu/drm/bridge/synopsys/dw-hdmi-qp.c | 124 ++++-
drivers/gpu/drm/display/drm_bridge_connector.c | 158 ++++--
drivers/gpu/drm/display/drm_hdmi_helper.c | 288 ++++++++++
drivers/gpu/drm/display/drm_hdmi_state_helper.c | 73 ++-
drivers/gpu/drm/display/drm_scdc_helper.c | 70 ++-
drivers/gpu/drm/drm_bridge.c | 6 +-
drivers/gpu/drm/drm_bridge_helper.c | 2 -
drivers/gpu/drm/drm_connector.c | 90 +++-
drivers/gpu/drm/rockchip/dw_hdmi_qp-rockchip.c | 191 ++++---
drivers/gpu/drm/rockchip/rk3066_hdmi.c | 2 +
drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c | 14 +-
drivers/gpu/drm/tests/drm_bridge_test.c | 2 +
drivers/gpu/drm/tests/drm_connector_test.c | 517 ++++++++++++------
drivers/gpu/drm/tests/drm_hdmi_state_helper_test.c | 595 +++++++++++++++------
drivers/gpu/drm/tests/drm_kunit_edid.c | 251 +++++++--
drivers/gpu/drm/tests/drm_kunit_edid.h | 1 +
drivers/gpu/drm/vc4/vc4_hdmi.c | 355 +++---------
drivers/gpu/drm/vc4/vc4_hdmi.h | 30 +-
include/drm/bridge/dw_hdmi_qp.h | 4 +-
include/drm/display/drm_hdmi_helper.h | 15 +
include/drm/display/drm_hdmi_state_helper.h | 6 +-
include/drm/display/drm_scdc_helper.h | 2 +
include/drm/drm_bridge.h | 49 ++
include/drm/drm_connector.h | 161 +++++-
include/linux/hdmi.h | 12 +
30 files changed, 2109 insertions(+), 994 deletions(-)
---
base-commit: 9c99e09777509d9bd8cabb0c1132c981b4e668e2
change-id: 20251203-dw-hdmi-qp-scramb-cdbd8b57ccf9