[PATCH v6 1/2] can: Add Loongson CAN-FD controller driver

Add a new driver for the Loongson CAN-FD controller, which is integrated
into Loongson-2K series SoCs. The controller supports both CAN 2.0 and
CAN-FD protocols, with up to 8 TX buffers and a flexible RX buffer.

The driver implements the core CAN device operations:
 - NAPI-based receive path with interrupt masking to reduce overhead;
 - TX echo support for accurate loopback and echo skb handling;
 - Error reporting (warning, passive, bus-off) with detailed status;
 - Support for common CAN controller modes: loopback, listen-only,
   one-shot, FD, and non-ISO FD;
 - Auto TDC (Transmitter Delay Compensation) for FD data phase.

Co-developed-by: Bingxiong Li <[email protected]>
Signed-off-by: Bingxiong Li <[email protected]>
Signed-off-by: Binbin Zhou <[email protected]>
---
 MAINTAINERS                      |    7 +
 drivers/net/can/Kconfig          |   11 +
 drivers/net/can/Makefile         |    1 +
 drivers/net/can/loongson_canfd.c | 1687 ++++++++++++++++++++++++++++++
 4 files changed, 1706 insertions(+)
 create mode 100644 drivers/net/can/loongson_canfd.c

diff --git a/MAINTAINERS b/MAINTAINERS
index f37a81950e25..6b39c880a05a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15193,6 +15193,13 @@ F:	Documentation/devicetree/bindings/sound/loongson,ls2k1000-i2s.yaml
 F:	sound/soc/loongson/loongson_*.c
 F:	sound/soc/loongson/loongson_*.h
 
+LOONGSON CAN FD DRIVER
+M:	Bingxiong Li <[email protected]>
+M:	Binbin Zhou <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	drivers/net/can/loongson_canfd/
+
 LOONGSON GPIO DRIVER
 M:	Yinbo Zhu <[email protected]>
 L:	[email protected]
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig
index a8fad6fe5302..95a0f898959c 100644
--- a/drivers/net/can/Kconfig
+++ b/drivers/net/can/Kconfig
@@ -186,6 +186,17 @@ config CAN_KVASER_PCIEFD
 	    Kvaser M.2 PCIe 4xCAN
 	    Kvaser PCIe 8xCAN
 
+config CAN_LOONGSON_CANFD
+	tristate "Loongson CAN-FD controller"
+	depends on HAS_IOMEM
+	select REGMAP_MMIO
+	help
+	  This is a canfd driver switch for the Loongson platform,
+	  integrated with the Loongson-2K series SoCs.
+
+	  To compile as a module, choose M here: the module will be
+	  called loongson_canfd.
+
 config CAN_SLCAN
 	tristate "Serial / USB serial CAN Adaptors (slcan)"
 	depends on TTY
diff --git a/drivers/net/can/Makefile b/drivers/net/can/Makefile
index 4010d17f8583..c4eae4595ce3 100644
--- a/drivers/net/can/Makefile
+++ b/drivers/net/can/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_CAN_GRCAN)		+= grcan.o
 obj-$(CONFIG_CAN_IFI_CANFD)	+= ifi_canfd/
 obj-$(CONFIG_CAN_JANZ_ICAN3)	+= janz-ican3.o
 obj-$(CONFIG_CAN_KVASER_PCIEFD)	+= kvaser_pciefd/
+obj-$(CONFIG_CAN_LOONGSON_CANFD)	+= loongson_canfd.o
 obj-$(CONFIG_CAN_MSCAN)		+= mscan/
 obj-$(CONFIG_CAN_M_CAN)		+= m_can/
 obj-$(CONFIG_CAN_PEAK_PCIEFD)	+= peak_canfd/
diff --git a/drivers/net/can/loongson_canfd.c b/drivers/net/can/loongson_canfd.c
new file mode 100644
index 000000000000..211133258b08
--- /dev/null
+++ b/drivers/net/can/loongson_canfd.c
@@ -0,0 +1,1687 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * LOONGSON CANFD controller
+ *
+ * Copyright (C) 2024-2026 Loongson Technology Corporation Limited
+ */
+
+#include <linux/acpi.h>
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/can/dev.h>
+#include <linux/can/error.h>
+#include <linux/ethtool.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/skbuff.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#define LOONGSON_CANFD_DEVICE_ID	0x0	/* CANFD controller ID Register */
+#define LOONGSON_CANFD_MODE		0x4	/* Mode Configuration Register */
+#define LOONGSON_CANFD_CONF		0x8	/* Configure Register */
+#define LOONGSON_CANFD_STAT		0xc	/* Status Register */
+#define LOONGSON_CANFD_CMD		0x10	/* Command Register */
+#define LOONGSON_CANFD_INT_STAT		0x14	/* Interrupt Status Register */
+#define LOONGSON_CANFD_INT_ENA		0x18	/* Interrupt Enable Register */
+#define LOONGSON_CANFD_INT_MASK		0x1c	/* Interrupt Mask Register */
+#define LOONGSON_CANFD_BTR_NORM		0x20	/* Normal Rate Configuration Register */
+#define LOONGSON_CANFD_BTR_FD		0x24	/* FD Data Rate Configuration Register */
+#define LOONGSON_CANFD_ERL		0x28	/* Error Threshold Configuration Register */
+#define LOONGSON_CANFD_FSTAT		0x2c	/* Error Status Register */
+#define LOONGSON_CANFD_ERC		0x30	/* Error Count Register */
+#define LOONGSON_CANFD_BRE		0x34	/* Rate Error Count Register */
+#define LOONGSON_CANFD_CTR_PRES		0x38	/* Error Count Debug Register */
+#define LOONGSON_CANFD_ERR_CAPT		0x3c	/* Error Capture Status Register */
+#define LOONGSON_CANFD_RETX_CNT		0x40	/* Retransmission Count Register */
+#define LOONGSON_CANFD_ALC		0x44	/* Lost Arbitration Capture Register */
+#define LOONGSON_CANFD_TRV_DLY		0x48	/* Transmission Delay Measurement Register */
+#define LOONGSON_CANFD_SSP_CFG		0x4c	/* Second Sampling Point Configuration Register */
+#define LOONGSON_CANFD_RX_FR_CNT	0x50	/* Receive Message Count Register */
+#define LOONGSON_CANFD_TX_FR_CNT	0x54	/* Transmit Message Count Register */
+#define LOONGSON_CANFD_DEBUG		0x58	/* Debug Register */
+#define LOONGSON_CANFD_TS		0x5c	/* Timestamp Register */
+#define LOONGSON_CANFD_TX_FRM_TST	0x60	/* Transmit Message Debug Register */
+#define LOONGSON_CANFD_FRC_DIV		0x64	/* Fractional Divider Ratio Register */
+#define LOONGSON_CANFD_FLT_A_MASK	0x68	/* Filter A Mask Register */
+#define LOONGSON_CANFD_FLT_A_VAL	0x6c	/* Filter A value Register */
+#define LOONGSON_CANFD_FLT_B_MASK	0x70	/* Filter B Mask Register */
+#define LOONGSON_CANFD_FLT_B_VAL	0x74	/* Filter B value Register */
+#define LOONGSON_CANFD_FLT_C_MASK	0x78	/* Filter C Mask Register */
+#define LOONGSON_CANFD_FLT_C_VAL	0x7c	/* Filter C value Register */
+#define LOONGSON_CANFD_FLT_R_LOW	0x80	/* Range Filter Low Threshold Register */
+#define LOONGSON_CANFD_FLT_R_HI		0x84	/* Range Filter High Threshold Register */
+#define LOONGSON_CANFD_FLT_CTRL		0x88	/* Filter Control Register */
+#define LOONGSON_CANFD_RX_MEM_INFO	0x8c	/* Receive Buffer Information Register */
+#define LOONGSON_CANFD_RX_PRT		0x90	/* Receive Buffer Pointer Register */
+#define LOONGSON_CANFD_RX_STAT		0x94	/* Receive Buffer Status Register */
+#define LOONGSON_CANFD_RX_DATA		0x98	/* Receive Data Register */
+#define LOONGSON_CANFD_TX_STAT		0x9c	/* Transmit Buffer Status Register */
+#define LOONGSON_CANFD_TX_CMD		0xa0	/* Transmit Command Register */
+#define LOONGSON_CANFD_TX_SEL		0xa4	/* Transmit Buffer Selection Register */
+#define LOONGSON_CANFD_TX_DATA_1	0xb0
+#define LOONGSON_CANFD_TX_DATA_18	0xf4
+
+/* Bitfields of CANFD controller ID register */
+#define REG_ID_MASK			GENMASK(15, 0)
+#define REG_ID_VER_MIN			GENMASK(23, 16)
+#define REG_ID_VER_MAJ			GENMASK(31, 24)
+
+/* Bitfields of Mode Configuration register */
+#define REG_MODE_RST			BIT(0)	/* Soft Reset */
+#define REG_MODE_BMM			BIT(1)	/* Bus Monitoring Mode */
+#define REG_MODE_STM			BIT(2)	/* Self-Test Mode */
+#define REG_MODE_AFM			BIT(3)	/* Receive Filter Mode */
+#define REG_MODE_FDE			BIT(4)	/* CANFD Enabled */
+#define REG_MODE_TTTM			BIT(5)	/* Timed Transmission Mode */
+#define REG_MODE_ROM			BIT(6)	/* Restricted Operation Mode */
+#define REG_MODE_ACF			BIT(7)	/* No ACK Mode*/
+#define REG_MODE_TSTM			BIT(8)	/* Test Mode */
+#define REG_MODE_RXBAM			BIT(9)	/* Receive Buffer Auto Mode */
+#define REG_MODE_ITSM			BIT(10)	/* Internal Timestamp Mode */
+#define REG_MODE_RTSOP			BIT(12)	/* Receive Buffer Timestamp Addition Mode */
+#define REG_MODE_BUFM			BIT(13)	/* Transmit Buffer Mode */
+
+/* Bitfields of Configure register */
+#define REG_CONF_RTRLE			BIT(0)	/* Retransmission Threshold Enable */
+#define REG_CONF_RTRTH			GENMASK(4, 1)	/* Retransmission Threshold */
+#define REG_CONF_ILBP			BIT(5)	/* Internal Loopback Mode */
+#define REG_CONF_ENA			BIT(6)	/* Controller Enable */
+#define REG_CONF_NISOFD			BIT(7)	/* NON-ISO CANFD Protocol Enable */
+#define REG_CONF_PEX			BIT(8)	/* Protocol Exception Handling */
+#define REG_CONF_FDRF			BIT(10)	/* Ignore Remote Frame Enable */
+
+/* Bitfields of Status register */
+#define REG_STAT_RXNE			BIT(0)	/* Receive Buffer Not Empty Status */
+#define REG_STAT_DOR			BIT(1)	/* Receive Data Overflow Status */
+#define REG_STAT_EFT			BIT(3)	/* Error Frame Flag */
+#define REG_STAT_RXS			BIT(4)	/* Receive Status Flag */
+#define REG_STAT_TXS			BIT(5)	/* Transmission Status Flag */
+#define REG_STAT_EWL			BIT(6)	/* Transmission Error Threshold Flag */
+#define REG_STAT_IDLE			BIT(7)	/* Bus Idle Flag */
+#define REG_STAT_PEXS			BIT(8)	/* Protocol Exception Status */
+#define REG_STAT_STCNT			BIT(16)	/* Transmission Count Support */
+
+/* Bitfields of Command register */
+#define REG_CMD_RXRPMV			BIT(1)	/* Receive Buffer Read-to-Move */
+#define REG_CMD_RRB			BIT(2)	/* Receive Buffer Release */
+#define REG_CMD_CDO			BIT(3)	/* Received Data Overflow Status Clear */
+#define REG_CMD_ERCRST			BIT(4)	/* Error Count Clear */
+#define REG_CMD_RXFCRST			BIT(5)	/* Receive Frame Count Clear */
+#define REG_CMD_TXFCRST			BIT(6)	/* Transmit Frame Count Clear */
+#define REG_CMD_CPEXS			BIT(7)	/* Exception Status Clear */
+
+/* Bitfields of Interrupt Status register */
+#define REG_INT_STAT_RXI		BIT(0)	/* Message Reception Interrupt */
+#define REG_INT_STAT_TXI		BIT(1)	/* Message Transmission Interrupt */
+#define REG_INT_STAT_EWLI		BIT(2)	/* Error Warning Threshold Interrupt */
+#define REG_INT_STAT_DOI		BIT(3)	/* Receive Data Overflow Interrupt */
+#define REG_INT_STAT_FCSI		BIT(4)	/* Fault State Change Interrupt */
+#define REG_INT_STAT_ALI		BIT(5)	/* Arbitration Loss Interrupt */
+#define REG_INT_STAT_BEI		BIT(6)	/* Bus Error Interrupt */
+#define REG_INT_STAT_RXFI		BIT(7)	/* Receive Buffer Full Interrupt */
+#define REG_INT_STAT_BSI		BIT(8)	/* Rate Switching Interrupt */
+#define REG_INT_STAT_RBNEI		BIT(9)	/* Receive Buffer Not Empty Interrupt */
+#define REG_INT_STAT_TXBHCI		BIT(10)	/* Transmit Buffer Hardware Command Interrupt */
+#define REG_INT_STAT_OFI		BIT(11)	/* Overload Frame Transmission Interrupt */
+#define REG_INT_STAT_DMADI		BIT(12)	/* Message DMA Transfer Complete Interrupt */
+
+#define REG_INT_STAT_ERRORI		(REG_INT_STAT_EWLI | REG_INT_STAT_FCSI |\
+					 REG_INT_STAT_ALI | REG_INT_STAT_BEI)
+
+/* Bitfields of Interrupt Enable register */
+#define REG_INT_ENA_SET			GENMASK(12, 0)
+#define REG_INT_ENA_CLR			GENMASK(28, 16)
+
+/* Bitfields of Interrupt Mask register */
+#define REG_INT_MASK_SET		GENMASK(12, 0)
+#define REG_INT_MASK_CLR		GENMASK(28, 16)
+
+/* Bitfields of Normal Rate Configuration register */
+#define REG_BTR_PROP			GENMASK(6, 0)
+#define REG_BTR_PH1			GENMASK(12, 7)
+#define REG_BTR_PH2			GENMASK(18, 13)
+#define REG_BTR_BRP			GENMASK(22, 19)
+#define REG_BTR_SJW			GENMASK(31, 27)
+
+/* Bitfields of FD Data Rate Configuration register */
+#define REG_BTR_FD_PROP			GENMASK(6, 0)
+#define REG_BTR_FD_PH1			GENMASK(12, 7)
+#define REG_BTR_FD_PH2			GENMASK(18, 13)
+#define REG_BTR_FD_BRP			GENMASK(26, 19)
+#define REG_BTR_FD_SJW			GENMASK(31, 27)
+
+/* Bitfields of Error Threshold Configuration register */
+#define REG_ERL_ERP			GENMASK(7, 0)
+#define REG_ERL_EW			GENMASK(23, 16)
+
+/* Bitfields of Error Status register */
+#define REG_FSTAT_ERA			BIT(0)
+#define REG_FSTAT_ERP			BIT(1)
+#define REG_FSTAT_BOF			BIT(2)
+
+#define REG_FSTAT_MASK			GENMASK(2, 0)
+
+/* Bitfields of Error Count register */
+#define REG_ERC_TEC			GENMASK(8, 0)
+#define REG_ERC_REC			GENMASK(24, 16)
+
+/* Bitfields of Rate Error Count register */
+#define REG_BRE_NORM			GENMASK(15, 0)
+#define REG_BRE_FD_DATA			GENMASK(31, 16)
+
+/* Bitfields of Error Count Debug register */
+#define REG_CTR_PRES_CTPV		GENMASK(8, 0)
+#define REG_CTR_PRES_PTX		BIT(9)
+#define REG_CTR_PRES_PRX		BIT(10)
+
+/* Bitfields of Error Capture Status register */
+#define REG_ERR_CAPT_POS		GENMASK(4, 0)
+#define REG_ERR_CAPT_TYPE		GENMASK(7, 5)
+
+/* Bitfields of Retransmission Count register */
+#define REG_RETX_CNT_VAL		GENMASK(3, 0)
+
+/* Bitfields of Lost Arbitration Capture register */
+#define REG_ALC_BIT_POS			GENMASK(4, 0)
+#define REG_ALC_ID_FIELD		GENMASK(7, 5)
+
+/* Bitfields of Transmission Delay Measurement register */
+#define REG_TRV_DLY_VAL			GENMASK(6, 0)
+
+/* Bitfields of Second Sampling Point Configuration register */
+#define REG_SSP_CFG_OFF			GENMASK(7, 0)
+#define REG_SSP_CFG_SRC			GENMASK(9, 8)
+#define REG_SSP_CFG_SAT			BIT(10)
+
+/* Bitfields of Receive Message Count register */
+#define REG_RX_FR_CNT_VAL		GENMASK(31, 0)
+
+/* Bitfields of Transmit Message Count register */
+#define REG_TX_FR_CNT_VAL		GENMASK(31, 0)
+
+/* Bitfields of Debug register */
+#define REG_DEBUG_STF_CNT		GENMASK(2, 0)
+#define REG_DEBUG_DSTF_CNT		GENMASK(5, 3)
+#define REG_DEBUG_PC_ARB		BIT(6)
+#define REG_DEBUG_PC_CON		BIT(7)
+#define REG_DEBUG_PC_DAT		BIT(8)
+#define REG_DEBUG_PC_STC		BIT(9)
+#define REG_DEBUG_PC_CRC		BIT(10)
+#define REG_DEBUG_PC_CRCD		BIT(11)
+#define REG_DEBUG_PC_ACK		BIT(12)
+#define REG_DEBUG_PC_ACKD		BIT(13)
+#define REG_DEBUG_PC_EOF		BIT(14)
+#define REG_DEBUG_PC_INT		BIT(15)
+#define REG_DEBUG_PC_SUSP		BIT(16)
+#define REG_DEBUG_PC_OVR		BIT(17)
+#define REG_DEBUG_PC_SOF		BIT(18)
+
+/* Bitfields of Timestamp register */
+#define REG_TS_TIMESTAMP		GENMASK(15, 0)
+#define REG_TS_PSC			GENMASK(24, 16)
+
+/* Bitfields of Fractional Divider Ratio register */
+#define REG_FRC_FRC_DBT			GENMASK(15, 8)
+#define REG_FRC_FRC_NBT			GENMASK(7, 0)
+
+/* Bitfields of Filter A Mask register */
+#define REG_FIL_A_MASK			GENMASK(28, 0)
+
+/* Bitfields of Filter A value register */
+#define REG_FIL_A_VAL			GENMASK(28, 0)
+
+/* Bitfields of Filter B Mask register */
+#define REG_FIL_B_MASK			GENMASK(28, 0)
+
+/* Bitfields of Filter B value register */
+#define REG_FIL_B_VAL			GENMASK(28, 0)
+
+/* Bitfields of Filter C Mask register */
+#define REG_FIL_C_MASK			GENMASK(28, 0)
+
+/* Bitfields of Filter C value register */
+#define REG_FIL_C_VAL			GENMASK(28, 0)
+
+/* Bitfields of Range Filter Low Threshold register */
+#define REG_FIL_R_LOW_VAL		GENMASK(28, 0)
+
+/* Bitfields of Range Filter High Threshold register */
+#define REG_FIL_R_HI_VAL		GENMASK(28, 0)
+
+/* Bitfields of Filter Control register */
+#define REG_FIL_CTRL_FANB		BIT(0)
+#define REG_FIL_CTRL_FANE		BIT(1)
+#define REG_FIL_CTRL_FAFB		BIT(2)
+#define REG_FIL_CTRL_FAFE		BIT(3)
+#define REG_FIL_CTRL_FBNB		BIT(4)
+#define REG_FIL_CTRL_FBNE		BIT(5)
+#define REG_FIL_CTRL_FBFB		BIT(6)
+#define REG_FIL_CTRL_FBFE		BIT(7)
+#define REG_FIL_CTRL_FCNB		BIT(8)
+#define REG_FIL_CTRL_FCNE		BIT(9)
+#define REG_FIL_CTRL_FCFB		BIT(10)
+#define REG_FIL_CTRL_FCFE		BIT(11)
+#define REG_FIL_CTRL_FRNB		BIT(12)
+#define REG_FIL_CTRL_FRNE		BIT(13)
+#define REG_FIL_CTRL_FRFB		BIT(14)
+#define REG_FIL_CTRL_FRFE		BIT(15)
+#define REG_FIL_CTRL_SFA		BIT(16)
+#define REG_FIL_CTRL_SFB		BIT(17)
+#define REG_FIL_CTRL_SFC		BIT(18)
+#define REG_FIL_CTRL_SFR		BIT(19)
+
+/* Bitfields of Receive Buffer Information register */
+#define REG_RX_MEM_INFO_BUFF_SIZE	GENMASK(12, 0)
+#define REG_RX_MEM_INFO_MEM_FREE	GENMASK(28, 16)
+
+/* Bitfields of Receive Buffer Pointer register */
+#define REG_RX_PTR_WPP			GENMASK(11, 0)
+#define REG_RX_PTR_RPP			GENMASK(27, 16)
+
+/* Bitfields of Receive Buffer Status register */
+#define REG_RX_STAT_RXE			BIT(0)
+#define REG_RX_STAT_RXF			BIT(1)
+#define REG_RX_STAT_RXMOF		BIT(2)
+#define REG_RX_STAT_RXFRC		GENMASK(14, 4)
+#define REG_RX_STAT_RTSOP		BIT(16)
+
+/* Bitfields of Receive Data register */
+#define REG_RX_DATA_VAL			GENMASK(31, 0)
+
+/* Bitfields of Transmit Buffer Status register */
+#define REG_TX_STAT_BRP			GENMASK(7, 0)
+#define REG_TX_STAT_TXS			GENMASK(10, 8)
+#define REG_TX_STAT_BS			GENMASK(31, 16)
+
+#define REG_TX_STAT_BS_TX_MASK_BASE	GENMASK(17, 16)
+
+/* Bitfields of Transmit Command register */
+#define REG_TX_CMD_BAR			GENMASK(7, 0)
+#define REG_TX_CMD_BCR			GENMASK(15, 8)
+#define REG_TX_CMD_BSC			GENMASK(23, 16)
+
+/* Bitfields of Transmit Buffer Selection register */
+#define REG_TX_SEL_BUF_SEL		GENMASK(3, 0)
+#define REG_TX_SEL_BUF_CNT		GENMASK(7, 4)
+
+/* Loongson CANFD Frame format */
+#define LOONGSON_CANFD_FRAME_META0	0x0
+#define LOONGSON_CANFD_FRAME_META1	0x4
+#define LOONGSON_CANFD_FRAME_DB_1	0x8
+
+/* Bitfields of FRAME META0 */
+#define REG_FRAME_META0_ID_EXT		GENMASK(17, 0)
+#define REG_FRAME_META0_ID_BASE		GENMASK(28, 18)
+#define REG_FRAME_META0_RTR		BIT(29)	/* Remote Transmission Request, only in CAN2.0 */
+/* Extended Identifier Type. 1: 29 bits ID, 0: 11 bits ID. */
+#define REG_FRAME_META0_XDT		BIT(30)
+#define REG_FRAME_META0_ESI		BIT(31)	/* Error State Indicator, only in CAN-FD */
+
+/* Bitfields of FRAME META1 */
+#define REG_FRAME_META1_TIMESTAMP	GENMASK(15, 0)
+#define REG_FRAME_META1_DLC		GENMASK(19, 16)	/* Data Length Code */
+#define REG_FRAME_META1_BRS		BIT(20)	/* Bit Rate Shift, Only in CANFD */
+/* Flexible Data-rate Format. 1: CANFD, 0: CAN2.0 */
+#define REG_FRAME_META1_FDF		BIT(21)
+#define REG_FRAME_META1_RWCNT		GENMASK(28, 24)	/* Read Word Counter */
+
+/* Bitfields of FRAME TEST */
+#define REG_FRAME_TEST_FSTC		BIT(0)
+#define REG_FRAME_TEST_FCRC		BIT(1)
+#define REG_FRAME_TEST_SDLC		BIT(2)
+#define REG_FRAME_TEST_TPRM		GENMASK(12, 8)
+
+#define DEV_NAME			"loongson_canfd"
+#define LOONGSON_CANFD_ID		0xBABE
+#define LOONGSON_CANFD_DW_BYTE		4
+#define LOONGSON_CANFD_TXBUF_NUM	8
+#define LOONGSON_CANFD_MAX_RTXTH	0xf
+
+/**
+ * struct loongson_canfd_priv - This definition define CAN driver instance
+ * @can: CAN private data structure.
+ * @napi: NAPI structure
+ * @regmap: regmap of the CAN device
+ * @res: Pointer to the CAN device respurce
+ * @tx_lock: Lock for synchronizing TX interrupt handling
+ */
+struct loongson_canfd_priv {
+	struct can_priv		can;		/* must be first member! */
+	struct napi_struct	napi;
+	struct regmap		*regmap;
+	struct resource		*res;
+	spinlock_t		tx_lock;	/* protect the sending queue */
+};
+
+/**
+ * enum loongson_canfd_txbuf_sts - status of TX buffer
+ * @TX_BS_IDLE: Status processed or not sent.
+ * @TX_BS_VALID: Sending successful.
+ * @TX_BS_FAIL: Sending failed.
+ * @TX_BS_CANCEL: Sending cancelled.
+ */
+enum loongson_canfd_txbuf_sts {
+	TX_BS_IDLE	= 0x0,
+	TX_BS_VALID	= 0x1,
+	TX_BS_FAIL	= 0x2,
+	TX_BS_CANCEL	= 0x3
+};
+
+/**
+ * enum loongson_canfd_txbuf_cmd - command of TX buffer
+ * @TXT_CMD_ADD: Buffer add request.
+ * @TXT_CMD_CANCEL: Buffer cancel request.
+ * @TXT_CMD_SR_CLEAN: Buffer send record clear.
+ *     1: to clear the send completion record (LOONGSON_CANFD_TX_STAT[BS]).
+ */
+enum loongson_canfd_txbuf_cmd {
+	TXT_CMD_ADD		= 0x01,
+	TXT_CMD_CANCEL		= 0x02,
+	TXT_CMD_SR_CLEAN	= 0x03
+};
+
+static const struct can_bittiming_const loongson_canfd_bit_timing = {
+	.name		= DEV_NAME,
+	.tseg1_min	= 2,
+	.tseg1_max	= 63,
+	.tseg2_min	= 2,
+	.tseg2_max	= 63,
+	.sjw_max	= 31,
+	.brp_min	= 1,
+	.brp_max	= 15,
+	.brp_inc	= 1,
+};
+
+static const struct can_bittiming_const loongson_canfd_bit_timing_data = {
+	.name		= DEV_NAME,
+	.tseg1_min	= 2,
+	.tseg1_max	= 63,
+	.tseg2_min	= 2,
+	.tseg2_max	= 63,
+	.sjw_max	= 31,
+	.brp_min	= 1,
+	.brp_max	= 255,
+	.brp_inc	= 1,
+};
+
+/* CAN FD Transmission Delay Compensation constants */
+static const struct can_tdc_const loongson_canfd_tdc_data = {
+	.tdcv_min	= 0,
+	.tdcv_max	= 0,
+	.tdco_min	= 1,
+	.tdco_max	= 127,
+	.tdcf_min	= 0,	/* Filter window not supported */
+	.tdcf_max	= 0,
+};
+
+/**
+ * loongson_canfd_enabled() - Gets the controller is enabled
+ * @priv: Pointer to private data
+ *
+ * Return: True - the controller is enabled.
+ *	   False - the controller is disabled.
+ */
+static bool loongson_canfd_enabled(struct loongson_canfd_priv *priv)
+{
+	return !!regmap_test_bits(priv->regmap, LOONGSON_CANFD_CONF, REG_CONF_ENA);
+}
+
+/**
+ * loongson_canfd_txbuf_freed() - Gets the flag for TX buffer to be sent
+ * @priv: Pointer to private data
+ *
+ * Return: True - TX buffer is empty.
+ *	   False - TX buffer is processing
+ */
+static bool loongson_canfd_txbuf_freed(struct loongson_canfd_priv *priv)
+{
+	return !regmap_test_bits(priv->regmap, LOONGSON_CANFD_TX_STAT, REG_TX_STAT_BRP);
+}
+
+/**
+ * loongson_canfd_disable_interrupts() - Disable all interrupts
+ * @priv: Pointer to private data
+ */
+static void loongson_canfd_disable_interrupts(struct loongson_canfd_priv *priv)
+{
+	regmap_write(priv->regmap, LOONGSON_CANFD_INT_ENA, FIELD_MAX(REG_INT_ENA_CLR) << 16);
+	regmap_write(priv->regmap, LOONGSON_CANFD_INT_MASK, FIELD_MAX(REG_INT_MASK_SET));
+}
+
+/**
+ * loongson_canfd_get_txbuf_sts() - Gets status of TX buffer
+ * @priv: Pointer to private data
+ * @buf_id: Buffer index (0-based)
+ *
+ * Return: Status of TX buffer
+ */
+static enum loongson_canfd_txbuf_sts
+loongson_canfd_get_txbuf_sts(struct loongson_canfd_priv *priv, u8 buf_id)
+{
+	u32 sts, mask;
+
+	mask = REG_TX_STAT_BS_TX_MASK_BASE << 2 * buf_id;
+	regmap_read(priv->regmap, LOONGSON_CANFD_TX_STAT, &sts);
+
+	return field_get(mask, sts);
+}
+
+/**
+ * loongson_canfd_txbuf_is_writable() - Checks if frame can be inserted to TX Buffer
+ * @priv: Pointer to private data
+ * @buf_id: Buffer index (0-based)
+ *
+ * Return: True - Frame can be inserted to TXT Buffer,
+ *	   False - If attempted, frame will not be inserted to TX Buffer
+ */
+static bool loongson_canfd_txbuf_is_writable(struct loongson_canfd_priv *priv, u8 buf_id)
+{
+	enum loongson_canfd_txbuf_sts bs;
+
+	bs = loongson_canfd_get_txbuf_sts(priv, buf_id);
+	if (bs)
+		return false;
+
+	return !regmap_test_bits(priv->regmap, LOONGSON_CANFD_TX_STAT, BIT(buf_id));
+}
+
+/**
+ * loongson_canfd_set_txbuf_cmd() - Applies command on TX buffer
+ * @ndev: Pointer to net_device structure
+ * @cmd: Command to set
+ * @buf_id: Buffer index (0-based)
+ */
+static void loongson_canfd_set_txbuf_cmd(struct net_device *ndev,
+					 enum loongson_canfd_txbuf_cmd cmd, u8 buf_id)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	u32 mask;
+
+	switch (cmd) {
+	case TXT_CMD_ADD:
+		mask = REG_TX_CMD_BAR;
+		break;
+	case TXT_CMD_CANCEL:
+		mask = REG_TX_CMD_BCR;
+		break;
+	case TXT_CMD_SR_CLEAN:
+		mask = REG_TX_CMD_BSC;
+		break;
+	default:
+		netdev_err(ndev, "Unknown command id: %x\n", cmd);
+		return;
+	}
+
+	regmap_write(priv->regmap, LOONGSON_CANFD_TX_CMD, field_prep(mask, BIT(buf_id)));
+}
+
+/**
+ * loongson_canfd_rxbuf_empty() - Gets the RX buffer is empty
+ * @priv: Pointer to private data
+ *
+ * Return: True - RX buffer is empty.
+ *	   False - RX buffer is processing
+ */
+static bool loongson_canfd_rxbuf_empty(struct loongson_canfd_priv *priv)
+{
+	return !!regmap_test_bits(priv->regmap, LOONGSON_CANFD_RX_STAT, REG_RX_STAT_RXE);
+}
+
+/**
+ * loongson_canfd_reset() - Issues software reset request to Loongson CANFD
+ * @ndev: Pointer to net_device structure
+ */
+static void loongson_canfd_reset(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+
+	regmap_write(priv->regmap, LOONGSON_CANFD_MODE, REG_MODE_RST);
+	regmap_write(priv->regmap, LOONGSON_CANFD_MODE, REG_MODE_RXBAM | REG_MODE_BUFM);
+}
+
+/**
+ * loongson_canfd_set_btr() - Sets CAN bus bit timing in Loongson CANFD
+ * @ndev: Pointer to net_device structure
+ * @bt: Pointer to Bit timing structure
+ * @nominal: True - Nominal bit timing, False - Data bit timing
+ */
+static void loongson_canfd_set_btr(struct net_device *ndev, struct can_bittiming *bt, bool nominal)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	u32 ph1_max = FIELD_MAX(REG_BTR_PH1);
+	u32 btr = 0;
+
+	/*
+	 * The timing calculation functions have only constraints on tseg1,
+	 * which is prop_seg + phase1_seg combined.
+	 * tseg1 is then split in half and stored into prog_seg and phase_seg1.
+	 * In Loongson CAN-FD, PROP is 7 bits wide but PH1 only 6, so we must
+	 * re-distribute the values here.
+	 */
+	if (bt->phase_seg1 > ph1_max) {
+		bt->prop_seg += bt->phase_seg1 - ph1_max;
+		bt->phase_seg1 = ph1_max;
+	}
+
+	if (nominal) {
+		btr = FIELD_PREP(REG_BTR_PROP, bt->prop_seg) |
+		      FIELD_PREP(REG_BTR_PH1, bt->phase_seg1) |
+		      FIELD_PREP(REG_BTR_PH2, bt->phase_seg2) |
+		      FIELD_PREP(REG_BTR_BRP, bt->brp) |
+		      FIELD_PREP(REG_BTR_SJW, bt->sjw);
+
+		regmap_write(priv->regmap, LOONGSON_CANFD_BTR_NORM, btr);
+	} else {
+		btr = FIELD_PREP(REG_BTR_FD_PROP, bt->prop_seg) |
+		      FIELD_PREP(REG_BTR_FD_PH1, bt->phase_seg1) |
+		      FIELD_PREP(REG_BTR_FD_PH2, bt->phase_seg2) |
+		      FIELD_PREP(REG_BTR_FD_BRP, bt->brp) |
+		      FIELD_PREP(REG_BTR_FD_SJW, bt->sjw);
+
+		regmap_write(priv->regmap, LOONGSON_CANFD_BTR_FD, btr);
+	}
+}
+
+/**
+ * loongson_canfd_set_bittiming() - CAN set nominal bit timing routine
+ * @ndev: Pointer to net_device structure
+ *
+ * Return: 0 on success, -%EPERM on error
+ */
+static int loongson_canfd_set_bittiming(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	struct can_bittiming *bt = &priv->can.bittiming;
+
+	/* Note that bt may be modified here */
+	loongson_canfd_set_btr(ndev, bt, true);
+
+	return 0;
+}
+
+/**
+ * loongson_canfd_set_data_bittiming() - CAN set data bit timing routine
+ * @ndev: Pointer to net_device structure
+ *
+ * Return: 0 on success, -%EPERM on error
+ */
+static int loongson_canfd_set_data_bittiming(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	struct can_bittiming *dbt = &priv->can.fd.data_bittiming;
+
+	/* Note that dbt may be modified here */
+	loongson_canfd_set_btr(ndev, dbt, false);
+
+	return 0;
+}
+
+/**
+ * loongson_canfd_get_auto_tdcv - Get Transmitter Delay Compensation Value
+ * @ndev: Pointer to net_device structure
+ * @tdcv: Pointer to TDCV value
+ *
+ * Return: 0 on success
+ */
+static int loongson_canfd_get_auto_tdcv(const struct net_device *ndev, u32 *tdcv)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	u32 val;
+
+	regmap_read(priv->regmap, LOONGSON_CANFD_TRV_DLY, &val);
+	*tdcv = FIELD_GET(REG_TRV_DLY_VAL, val);
+
+	return 0;
+}
+
+/**
+ * loongson_canfd_set_secondary_sample_point() - Set secondary sample point in Loongson CANFD
+ * @ndev: Pointer to net_device structure
+ *
+ * Return: 0 on success, -%EPERM if controller is enabled
+ */
+static int loongson_canfd_set_secondary_sample_point(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	u32 ssp_cfg;
+
+	if (loongson_canfd_enabled(priv)) {
+		netdev_err(ndev, "BUG! Cannot set SSP - CAN is enabled\n");
+		return -EPERM;
+	}
+
+	if (can_fd_tdc_is_enabled(&priv->can))
+		ssp_cfg = FIELD_PREP(REG_SSP_CFG_OFF, priv->can.fd.tdc.tdco) |
+			  FIELD_PREP(REG_SSP_CFG_SRC, 0x0);
+	else
+		ssp_cfg = FIELD_PREP(REG_SSP_CFG_SRC, 0x1);
+
+	regmap_write(priv->regmap, LOONGSON_CANFD_SSP_CFG, ssp_cfg);
+
+	return 0;
+}
+
+/**
+ * loongson_canfd_set_conf_mode() - Sets Loongson CANFD mode and configure registers
+ * @priv: Pointer to private data
+ */
+static void loongson_canfd_set_conf_mode(struct loongson_canfd_priv *priv)
+{
+	u32 ctrlmode = priv->can.ctrlmode;
+	u32 mode, conf;
+
+	regmap_read(priv->regmap, LOONGSON_CANFD_MODE, &mode);
+
+	if (ctrlmode & CAN_CTRLMODE_LISTENONLY)
+		mode |= REG_MODE_BMM;
+	else
+		mode &= ~REG_MODE_BMM;
+
+	if (ctrlmode & CAN_CTRLMODE_FD)
+		mode |= REG_MODE_FDE;
+	else
+		mode &= ~REG_MODE_FDE;
+
+	if (ctrlmode & CAN_CTRLMODE_PRESUME_ACK)
+		mode |= REG_MODE_ACF;
+	else
+		mode &= ~REG_MODE_ACF;
+
+	/*
+	 * Some bits fixed:
+	 * TSTM - Off, User shall not be able to change REC/TEC by hand
+	 * during operation
+	 */
+	mode &= ~REG_MODE_TSTM;
+	regmap_write(priv->regmap, LOONGSON_CANFD_MODE, mode);
+
+	regmap_read(priv->regmap, LOONGSON_CANFD_CONF, &conf);
+
+	if (ctrlmode & CAN_CTRLMODE_LOOPBACK)
+		conf |= REG_CONF_ILBP;
+	else
+		conf &= ~REG_CONF_ILBP;
+
+	if (ctrlmode & CAN_CTRLMODE_FD_NON_ISO)
+		conf |= REG_CONF_NISOFD;
+	else
+		conf &= ~REG_CONF_NISOFD;
+
+	/* One shot mode supported indirectly via Retransmit limit */
+	conf &= ~FIELD_PREP(REG_CONF_RTRTH, LOONGSON_CANFD_MAX_RTXTH);
+
+	if (ctrlmode & CAN_CTRLMODE_ONE_SHOT)
+		conf |= REG_CONF_RTRLE;
+	else
+		conf |= REG_CONF_RTRLE | FIELD_PREP(REG_CONF_RTRTH, LOONGSON_CANFD_MAX_RTXTH);
+
+	regmap_write(priv->regmap, LOONGSON_CANFD_CONF, conf);
+}
+
+/**
+ * loongson_canfd_chip_start() - This routine starts the driver
+ * @ndev: Pointer to net_device structure
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int loongson_canfd_chip_start(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	u16 int_ena, int_msk;
+	int ret;
+
+	/* Configure bit-rates and ssp */
+	ret = loongson_canfd_set_bittiming(ndev);
+	if (ret < 0)
+		return ret;
+
+	ret = loongson_canfd_set_data_bittiming(ndev);
+	if (ret < 0)
+		return ret;
+
+	ret = loongson_canfd_set_secondary_sample_point(ndev);
+	if (ret < 0)
+		return ret;
+
+	/* Setting mode and configure registers */
+	loongson_canfd_set_conf_mode(priv);
+
+	/* Configure interrupts */
+	int_ena = REG_INT_STAT_RBNEI | REG_INT_STAT_TXBHCI |
+		  REG_INT_STAT_EWLI | REG_INT_STAT_FCSI;
+
+	/* Bus error reporting */
+	if (priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)
+		int_ena |= REG_INT_STAT_ALI | REG_INT_STAT_BEI;
+
+	int_msk = FIELD_GET(REG_INT_MASK_SET, ~int_ena); /* Mask all disabled interrupts */
+
+	/* It's after reset, so there is no need to clear anything */
+	regmap_write(priv->regmap, LOONGSON_CANFD_INT_MASK, int_msk);
+	regmap_write(priv->regmap, LOONGSON_CANFD_INT_ENA, int_ena);
+
+	/* Controller enters ERROR_ACTIVE on initial FCSI */
+	priv->can.state = CAN_STATE_STOPPED;
+
+	/* Enable the controller */
+	regmap_update_bits(priv->regmap, LOONGSON_CANFD_CONF, REG_CONF_ENA, REG_CONF_ENA);
+
+	return 0;
+}
+
+/**
+ * loongson_canfd_do_set_mode() - Sets mode of the driver
+ * @ndev: Pointer to net_device structure
+ * @mode: Tells the mode of the driver
+ *
+ * This check the drivers state and calls the corresponding modes to set.
+ *
+ * Return: 0 on success and failure value on error
+ */
+static int loongson_canfd_do_set_mode(struct net_device *ndev, enum can_mode mode)
+{
+	int ret;
+
+	switch (mode) {
+	case CAN_MODE_START:
+		loongson_canfd_reset(ndev);
+
+		ret = loongson_canfd_chip_start(ndev);
+		if (ret < 0) {
+			netdev_err(ndev, "loongson_canfd_chip_start failed!\n");
+			return ret;
+		}
+
+		netif_wake_queue(ndev);
+		break;
+	default:
+		ret = -EOPNOTSUPP;
+		break;
+	}
+
+	return ret;
+}
+
+/**
+ * loongson_canfd_insert_frame() - Inserts frame to TXT buffer
+ * @priv: Pointer to private data
+ * @cf:	 Pointer to CAN frame to be inserted
+ * @buf: TXT Buffer index to which frame is inserted (0-based)
+ * @isfdf: True - CAN FD Frame, False - CAN 2.0 Frame
+ *
+ * Return:
+ * * True - Frame inserted successfully
+ * * False - Frame was not inserted due to one of:
+ *	1. TXT Buffer is not writable (it is in wrong state)
+ *	2. Invalid TXT buffer index
+ *	3. Invalid frame length
+ */
+static bool loongson_canfd_insert_frame(struct loongson_canfd_priv *priv,
+					const struct canfd_frame *cf, u8 buf, bool isfdf)
+{
+	u32 meta0, meta1 = 0;
+
+	if (buf >= LOONGSON_CANFD_TXBUF_NUM)
+		return false;
+
+	if (!loongson_canfd_txbuf_is_writable(priv, buf))
+		return false;
+
+	/* Prepare identifier */
+	if (cf->can_id & CAN_EFF_FLAG) {
+		meta0 = cf->can_id & CAN_EFF_MASK;
+		meta0 |= REG_FRAME_META0_XDT;
+	} else {
+		meta0 = FIELD_PREP(REG_FRAME_META0_ID_BASE, cf->can_id & CAN_SFF_MASK);
+	}
+
+	/* Prepare Frame format */
+	if (cf->can_id & CAN_RTR_FLAG)
+		meta0 |= REG_FRAME_META0_RTR;
+
+	if (isfdf) {
+		meta1 = REG_FRAME_META1_FDF;
+
+		if (cf->flags & CANFD_BRS)
+			meta1 |= REG_FRAME_META1_BRS;
+	}
+
+	meta1 |= FIELD_PREP(REG_FRAME_META1_DLC, can_fd_len2dlc(cf->len));
+
+	/* TXT buffer select */
+	regmap_write(priv->regmap, LOONGSON_CANFD_TX_SEL, buf);
+
+	/* Write ID, Frame format */
+	regmap_write(priv->regmap, LOONGSON_CANFD_TX_DATA_1 + LOONGSON_CANFD_FRAME_META0, meta0);
+	regmap_write(priv->regmap, LOONGSON_CANFD_TX_DATA_1 + LOONGSON_CANFD_FRAME_META1, meta1);
+
+	if (cf->can_id & CAN_RTR_FLAG)
+		return true;
+
+	/* Write Data payload */
+	for (unsigned int i = 0; i < cf->len; i += LOONGSON_CANFD_DW_BYTE) {
+		regmap_write(priv->regmap,
+			     LOONGSON_CANFD_TX_DATA_1 + LOONGSON_CANFD_FRAME_DB_1 + i,
+			     *(u32 *)(cf->data + i));
+	}
+
+	return true;
+}
+
+/**
+ * loongson_canfd_start_xmit() - Starts the transmission
+ * @skb: sk_buff pointer that contains data to be Txed
+ * @ndev: Pointer to net_device structure
+ *
+ * Invoked from upper layers to initiate transmission. Uses the next available free TX Buffer and
+ * populates its fields to start the transmission.
+ *
+ * Return: %NETDEV_TX_OK on success,
+ *         %NETDEV_TX_BUSY when no free TX buffer is available, negative return values reserved
+ *         for error cases.
+ */
+static netdev_tx_t loongson_canfd_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	struct canfd_frame *cf = (struct canfd_frame *)skb->data;
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	u32 buf_id = 0, tx_stat, i = 0;
+	unsigned long tx_brp;
+	u16 tx_bs;
+
+	if (can_dropped_invalid_skb(ndev, skb))
+		return NETDEV_TX_OK;
+
+	guard(spinlock_irqsave)(&priv->tx_lock);
+
+	if (unlikely(!loongson_canfd_txbuf_freed(priv))) {
+		netif_stop_queue(ndev);
+		netdev_err(ndev, "BUG!, no TXB free when queue awake!\n");
+		return NETDEV_TX_BUSY;
+	}
+
+	regmap_read(priv->regmap, LOONGSON_CANFD_TX_STAT, &tx_stat);
+	tx_brp = FIELD_GET(REG_TX_STAT_BRP, tx_stat);
+	tx_bs = FIELD_GET(REG_TX_STAT_BS, tx_stat);
+
+	for_each_clear_bit(i, &tx_brp, LOONGSON_CANFD_TXBUF_NUM) {
+		u32 transmission_complete_mask = 0x3 << (i * 2);
+
+		if (!(tx_bs & transmission_complete_mask)) {
+			buf_id = i;
+			break;
+		}
+	}
+
+	if (!loongson_canfd_insert_frame(priv, cf, buf_id, can_is_canfd_skb(skb))) {
+		netdev_err(ndev, "TXNF set but cannot insert frame into TXTB! HW Bug?");
+		dev_kfree_skb_any(skb);
+		ndev->stats.tx_dropped++;
+		return NETDEV_TX_OK;
+	}
+
+	can_put_echo_skb(skb, ndev, buf_id, 0);
+
+	loongson_canfd_set_txbuf_cmd(ndev, TXT_CMD_ADD, buf_id);
+
+	/* Check if all TX buffers are full */
+	if (!loongson_canfd_txbuf_freed(priv))
+		netif_stop_queue(ndev);
+
+	return NETDEV_TX_OK;
+}
+
+/**
+ * loongson_canfd_rx() -  Called from CAN ISR to complete the received frame processing
+ * @ndev: Pointer to net_device structure
+ *
+ * This function is invoked from the CAN isr to process the Rx frames. It does minimal
+ * processing and invokes "netif_receive_skb" to complete further processing.
+ * Return: 1 when frame is passed to the network layer or system is out of free SKBs
+ *         temporally and left code to resolve SKB allocation later, -%EAGAIN in a case
+ *         of empty Rx FIFO.
+ */
+static int loongson_canfd_rx(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	struct net_device_stats *stats = &ndev->stats;
+	u32 meta0, meta1, dlc, rwcnt, dbcnt, i, data;
+	struct canfd_frame *cfd;
+	struct can_frame *ccf;
+	struct sk_buff *skb;
+	bool is_can_fd;
+
+	regmap_read(priv->regmap, LOONGSON_CANFD_RX_DATA, &meta0);
+	regmap_read(priv->regmap, LOONGSON_CANFD_RX_DATA, &meta1);
+
+	/* Number of characters received */
+	rwcnt = FIELD_GET(REG_FRAME_META1_RWCNT, meta1);
+	if (!rwcnt)
+		return -EAGAIN;
+	dbcnt = (rwcnt - 2) * LOONGSON_CANFD_DW_BYTE;
+
+	/* Flexible Data-rate Format */
+	is_can_fd = meta1 & REG_FRAME_META1_FDF;
+	if (is_can_fd) {
+		skb = alloc_canfd_skb(ndev, &cfd);
+	} else {
+		skb = alloc_can_skb(ndev, &ccf);
+		cfd = (struct canfd_frame *)ccf;
+	}
+
+	if (unlikely(!skb)) {
+		for (i = 0; i < dbcnt; i += LOONGSON_CANFD_DW_BYTE)
+			regmap_read(priv->regmap, LOONGSON_CANFD_RX_DATA, &data);
+		ndev->stats.rx_dropped++;
+		return 1;
+	}
+
+	/* Extended Identifier Type */
+	if (meta0 & REG_FRAME_META0_XDT)
+		cfd->can_id = (meta0 & CAN_EFF_MASK) | CAN_EFF_FLAG;
+	else
+		cfd->can_id = FIELD_GET(REG_FRAME_META0_ID_BASE, meta0) & CAN_SFF_MASK;
+
+	/* BRS, ESI, RTR Flags */
+	cfd->flags = 0;
+
+	if (is_can_fd) {
+		if (meta1 & REG_FRAME_META1_BRS)
+			cfd->flags |= CANFD_BRS;
+
+		if (meta0 & REG_FRAME_META0_ESI)
+			cfd->flags |= CANFD_ESI;
+	} else if (meta0 & REG_FRAME_META0_RTR) {
+		cfd->can_id |= CAN_RTR_FLAG;
+	}
+
+	/* Data Length Code */
+	dlc = FIELD_GET(REG_FRAME_META1_DLC, meta1);
+	if (is_can_fd)
+		cfd->len = can_fd_dlc2len(dlc);
+	else
+		can_frame_set_cc_len(ccf, dlc, priv->can.ctrlmode);
+
+	/* Copy payload */
+	for (i = 0; i < dbcnt; i += LOONGSON_CANFD_DW_BYTE)
+		regmap_read(priv->regmap, LOONGSON_CANFD_RX_DATA, (u32 *)(cfd->data + i));
+
+	/* Drain any residual (should not happen) */
+	while (unlikely(i < dbcnt)) {
+		regmap_read(priv->regmap, LOONGSON_CANFD_RX_DATA, &data);
+		i += LOONGSON_CANFD_DW_BYTE;
+	}
+
+	if (!(cfd->can_id & CAN_RTR_FLAG))
+		stats->rx_bytes += cfd->len;
+	stats->rx_packets++;
+	netif_receive_skb(skb);
+
+	return 1;
+}
+
+/**
+ * loongson_canfd_read_fault_state() - Reads Loongson CANFD fault state.
+ * @ndev: Pointer to net_device structure
+ *
+ * Returns: Fault confinement state of controller
+ */
+static enum can_state loongson_canfd_read_fault_state(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	enum can_state sts = CAN_STATE_ERROR_PASSIVE;
+	u32 fstat, ewl, erl, rec_tec, max_tec;
+
+	regmap_read(priv->regmap, LOONGSON_CANFD_FSTAT, &fstat);
+
+	switch (FIELD_GET(REG_FSTAT_MASK, fstat)) {
+	case REG_FSTAT_ERA:
+
+		regmap_read(priv->regmap, LOONGSON_CANFD_ERL, &erl);
+		regmap_read(priv->regmap, LOONGSON_CANFD_ERC, &rec_tec);
+
+		ewl = FIELD_GET(REG_ERL_EW, erl);
+		max_tec = max(FIELD_GET(REG_ERC_REC, rec_tec), FIELD_GET(REG_ERC_TEC, rec_tec));
+
+		if (ewl > max_tec)
+			sts = CAN_STATE_ERROR_ACTIVE;
+		else
+			sts = CAN_STATE_ERROR_WARNING;
+		break;
+	case REG_FSTAT_ERP:
+		sts = CAN_STATE_ERROR_PASSIVE;
+		break;
+	case REG_FSTAT_BOF:
+		sts = CAN_STATE_BUS_OFF;
+		break;
+	default:
+		netdev_err(ndev, "Invalid error state.\n");
+		break;
+	}
+
+	return sts;
+}
+
+/**
+ * loongson_canfd_get_bec() - Reads REC/TEC counter values from controller
+ * @priv: Pointer to private data
+ * @bec: Pointer to Error counter structure
+ */
+static void loongson_canfd_get_bec(struct loongson_canfd_priv *priv, struct can_berr_counter *bec)
+{
+	u32 erc;
+
+	regmap_read(priv->regmap, LOONGSON_CANFD_ERC, &erc);
+	bec->rxerr = FIELD_GET(REG_ERC_REC, erc);
+	bec->txerr = FIELD_GET(REG_ERC_TEC, erc);
+}
+
+/**
+ * loongson_canfd_get_berr_counter() - error counter routine
+ * @ndev: Pointer to net_device structure
+ * @bec: Pointer to can_berr_counter structure
+ *
+ * Return: 0 always
+ */
+static int loongson_canfd_get_berr_counter(const struct net_device *ndev,
+					   struct can_berr_counter *bec)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+
+	loongson_canfd_get_bec(priv, bec);
+	return 0;
+}
+
+/**
+ * loongson_canfd_err_interrupt() - Error frame ISR
+ * @ndev: net_device pointer
+ * @isr: interrupt status register value
+ *
+ * This is the CAN error interrupt and it will check the type of error and forward the error
+ * frame to upper layers.
+ */
+static void loongson_canfd_err_interrupt(struct net_device *ndev, u32 isr)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	struct net_device_stats *stats = &ndev->stats;
+	struct can_berr_counter bec;
+	u32 capt, alc, mask = 0;
+	enum can_state state;
+	struct can_frame *cf;
+	struct sk_buff *skb;
+
+	loongson_canfd_get_bec(priv, &bec);
+
+	state = loongson_canfd_read_fault_state(ndev);
+	regmap_read(priv->regmap, LOONGSON_CANFD_ERR_CAPT, &capt);
+	regmap_read(priv->regmap, LOONGSON_CANFD_ALC, &alc);
+
+	netdev_dbg(ndev, "%s: ISR 0x%08x, rxerr %d, txerr %d, error type %lu, pos %lu, ALC id_field %lu, bit %lu\n",
+		   __func__, isr, bec.rxerr, bec.txerr,
+		   FIELD_GET(REG_ERR_CAPT_TYPE, capt), FIELD_GET(REG_ERR_CAPT_POS, capt),
+		   FIELD_GET(REG_ALC_ID_FIELD, alc), FIELD_GET(REG_ALC_BIT_POS, alc));
+
+	skb = alloc_can_err_skb(ndev, &cf);
+
+	/*
+	 * EWLI: error warning limit condition met
+	 * FCSI: fault confinement state changed
+	 * ALI:  arbitration lost (just informative)
+	 * BEI:  bus error interrupt
+	 */
+	if ((isr & REG_INT_STAT_FCSI) || (isr & REG_INT_STAT_EWLI)) {
+		netdev_info(ndev, "state changes from %s to %s\n",
+			    can_get_state_str(priv->can.state), can_get_state_str(state));
+
+		if (priv->can.state == state)
+			netdev_warn(ndev, "cur and pre state is the same!(miss intr?)\n");
+
+		mask |= REG_INT_STAT_FCSI | REG_INT_STAT_EWLI;
+		priv->can.state = state;
+		switch (state) {
+		case CAN_STATE_BUS_OFF:
+			priv->can.can_stats.bus_off++;
+			can_bus_off(ndev);
+			if (skb)
+				cf->can_id |= CAN_ERR_BUSOFF;
+			break;
+		case CAN_STATE_ERROR_PASSIVE:
+			priv->can.can_stats.error_passive++;
+			if (skb) {
+				cf->can_id |= CAN_ERR_CRTL | CAN_ERR_CNT;
+				if (bec.rxerr >= CAN_ERROR_PASSIVE_THRESHOLD)
+					cf->data[1] = CAN_ERR_CRTL_RX_PASSIVE;
+				else
+					cf->data[1] = CAN_ERR_CRTL_TX_PASSIVE;
+				cf->data[6] = bec.txerr;
+				cf->data[7] = bec.rxerr;
+			}
+			break;
+		case CAN_STATE_ERROR_WARNING:
+			priv->can.can_stats.error_warning++;
+			if (skb) {
+				cf->can_id |= CAN_ERR_CRTL | CAN_ERR_CNT;
+				if (bec.txerr > bec.rxerr)
+					cf->data[1] |= CAN_ERR_CRTL_TX_WARNING;
+				else
+					cf->data[1] |= CAN_ERR_CRTL_RX_WARNING;
+				cf->data[6] = bec.txerr;
+				cf->data[7] = bec.rxerr;
+			}
+			break;
+		case CAN_STATE_ERROR_ACTIVE:
+			if (skb) {
+				cf->can_id |= CAN_ERR_CNT;
+				cf->data[1] = CAN_ERR_CRTL_ACTIVE;
+				cf->data[6] = bec.txerr;
+				cf->data[7] = bec.rxerr;
+			}
+			break;
+		default:
+			netdev_err(ndev, "Unexpected state: %d, %s!\n", state,
+				   can_get_state_str(state));
+			break;
+		}
+	}
+
+	/* Check for Arbitration Lost interrupt */
+	if (isr & REG_INT_STAT_ALI) {
+		mask |= REG_INT_STAT_ALI;
+		netdev_err(ndev, "Arbitration Lost interrupt\n");
+		priv->can.can_stats.arbitration_lost++;
+		if (skb) {
+			cf->can_id |= CAN_ERR_LOSTARB;
+			cf->data[0] = CAN_ERR_LOSTARB_UNSPEC;
+		}
+	}
+
+	/* Check for Bus Error interrupt */
+	if (isr & REG_INT_STAT_BEI) {
+		mask |= REG_INT_STAT_BEI;
+		netdev_err(ndev, "Bus Error interrupt\n");
+		priv->can.can_stats.bus_error++;
+		stats->rx_errors++;
+		if (skb) {
+			cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+			cf->data[2] = CAN_ERR_PROT_UNSPEC;
+			cf->data[3] = CAN_ERR_PROT_LOC_UNSPEC;
+		}
+	}
+
+	if (skb)
+		netif_rx(skb);
+
+	regmap_write(priv->regmap, LOONGSON_CANFD_INT_STAT, mask);
+	regmap_write(priv->regmap, LOONGSON_CANFD_INT_MASK, mask << 16);
+}
+
+static int loongson_canfd_rx_napi(struct napi_struct *napi, int quota)
+{
+	struct net_device *ndev = napi->dev;
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	int work_done = 0, ret = 1;
+	bool rxbuf_is_empty;
+	u32 sts;
+
+	rxbuf_is_empty = loongson_canfd_rxbuf_empty(priv);
+
+	while (!rxbuf_is_empty && work_done < quota && ret != -EAGAIN) {
+		ret = loongson_canfd_rx(ndev);
+		work_done++;
+		rxbuf_is_empty = loongson_canfd_rxbuf_empty(priv);
+	}
+
+	/* Check for RX FIFO Overflow */
+	regmap_read(priv->regmap, LOONGSON_CANFD_STAT, &sts);
+	if (sts & REG_STAT_DOR) {
+		struct net_device_stats *stats = &ndev->stats;
+		struct can_frame *cf;
+		struct sk_buff *skb;
+
+		netdev_info(ndev, "Loongson canfd RX overflow\n");
+		stats->rx_over_errors++;
+		stats->rx_errors++;
+
+		skb = alloc_can_err_skb(ndev, &cf);
+		if (skb) {
+			cf->can_id |= CAN_ERR_CRTL;
+			cf->data[1] |= CAN_ERR_CRTL_RX_OVERFLOW;
+			netif_rx(skb);
+		}
+
+		/* Clear Data Overrun */
+		regmap_write(priv->regmap, LOONGSON_CANFD_CMD, REG_CMD_CDO);
+	}
+
+	if (rxbuf_is_empty) {
+		if (napi_complete_done(napi, work_done)) {
+			/*
+			 * Clear and enable RBNEI. It is level-triggered,
+			 * so there is no race condition.
+			 */
+			regmap_write(priv->regmap, LOONGSON_CANFD_INT_STAT, REG_INT_STAT_RBNEI);
+			regmap_write(priv->regmap, LOONGSON_CANFD_INT_MASK,
+				     (REG_INT_STAT_RBNEI << 16));
+		}
+	}
+
+	return work_done;
+}
+
+/**
+ * loongson_canfd_tx_interrupt() - Tx done Isr
+ * @ndev: net_device pointer
+ */
+static void loongson_canfd_tx_interrupt(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	struct net_device_stats *stats = &ndev->stats;
+	enum loongson_canfd_txbuf_sts sts;
+	u8 processed_mask = 0;
+	u32 buf_id, cnt;
+
+	guard(spinlock_irqsave)(&priv->tx_lock);
+
+	for (buf_id = 0; buf_id < LOONGSON_CANFD_TXBUF_NUM; buf_id++) {
+		if (processed_mask & BIT(buf_id))
+			continue;
+
+		sts = loongson_canfd_get_txbuf_sts(priv, buf_id);
+		if (sts == TX_BS_IDLE)
+			continue;
+		processed_mask |= BIT(buf_id);
+
+		switch (sts) {
+		case TX_BS_VALID:
+			stats->tx_bytes += can_get_echo_skb(ndev, buf_id, NULL);
+			stats->tx_packets++;
+			break;
+		case TX_BS_FAIL:
+			/*
+			 * This indicated that retransmit limit has been reached.
+			 * Obviously we should not echo the frame, but also not indicate any
+			 * kind of error. If desired, it was already reported (possible
+			 * multiple times) on each arbitration lost.
+			 */
+			regmap_read(priv->regmap, LOONGSON_CANFD_TX_FR_CNT, &cnt);
+			netdev_warn(ndev, "TXB in FAIL state, TX frame count: %d\n", cnt);
+			can_free_echo_skb(ndev, buf_id, NULL);
+			stats->tx_dropped++;
+			break;
+		case TX_BS_CANCEL:
+			/*
+			 * We *could* re-queue the frame, but multiqueue/abort is
+			 * not supported yet anyway.
+			 */
+			netdev_warn(ndev, "TXB in CANCEL state\n");
+			can_free_echo_skb(ndev, buf_id, NULL);
+			stats->tx_dropped++;
+			break;
+		default:
+			netdev_warn(ndev, "TXB unexpected status: %d\n", sts);
+			break;
+		}
+
+		loongson_canfd_set_txbuf_cmd(ndev, TXT_CMD_SR_CLEAN, buf_id);
+	}
+
+	/*
+	 * If no buffers were processed this time, we cannot clear - that would introduce
+	 * a race condition.
+	 */
+	if (processed_mask) {
+		/*
+		 * Clear the interrupt again. We do not want to receive again interrupt
+		 * for the buffer already handled. If it is the last finished one then
+		 * it would cause log of spurious interrupt.
+		 */
+		regmap_write(priv->regmap, LOONGSON_CANFD_INT_STAT, REG_INT_STAT_TXBHCI);
+	}
+
+	/* Check if at least one TX buffer is free */
+	if (loongson_canfd_txbuf_freed(priv))
+		netif_wake_queue(ndev);
+}
+
+/**
+ * loongson_canfd_interrupt() - CAN Isr
+ * @irq: irq number
+ * @dev_id: device id pointer
+ *
+ * This is the Loongson CANFD ISR. It checks for the type of interrupt
+ * and invokes the corresponding ISR.
+ *
+ * Return:
+ * IRQ_NONE - If CAN device is in sleep mode, IRQ_HANDLED otherwise
+ */
+static irqreturn_t loongson_canfd_interrupt(int irq, void *dev_id)
+{
+	struct net_device *ndev = (struct net_device *)dev_id;
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	u32 isr, imask;
+
+	for (unsigned int irq_loops = 0; irq_loops < 10000; irq_loops++) {
+		/* Get the interrupt status */
+		regmap_read(priv->regmap, LOONGSON_CANFD_INT_STAT, &isr);
+		if (!isr) {
+			if (irq_loops)
+				return IRQ_HANDLED;
+			else
+				return IRQ_NONE;
+		}
+
+		/* Receive Buffer Not Empty Interrupt */
+		if (isr & REG_INT_STAT_RBNEI) {
+			/*
+			 * Mask RXBNEI the first, then clear interrupt and schedule NAPI.
+			 * Even if another IRQ fires, RBNEI will always be 0 (masked).
+			 */
+			regmap_write(priv->regmap, LOONGSON_CANFD_INT_MASK, REG_INT_STAT_RBNEI);
+			regmap_write(priv->regmap, LOONGSON_CANFD_INT_STAT, REG_INT_STAT_RBNEI);
+			napi_schedule(&priv->napi);
+		}
+
+		/* TX Buffer HW Command Interrupt */
+		if (isr & REG_INT_STAT_TXBHCI)
+			loongson_canfd_tx_interrupt(ndev);
+
+		/* Error interrupts */
+		imask = isr & REG_INT_STAT_ERRORI;
+		if (imask) {
+			regmap_write(priv->regmap, LOONGSON_CANFD_INT_MASK, imask);
+			regmap_write(priv->regmap, LOONGSON_CANFD_INT_STAT, imask);
+			loongson_canfd_err_interrupt(ndev, isr);
+		}
+
+		/* Ignore RI, TI, LFI, RFI, BSI */
+	}
+
+	netdev_err(ndev, "Intterupt state: 0x%x.\n", isr);
+
+	if (isr & REG_INT_STAT_TXBHCI) {
+		for (unsigned int i = 0; i < LOONGSON_CANFD_TXBUF_NUM; i++) {
+			u32 sts = loongson_canfd_get_txbuf_sts(priv, i);
+
+			netdev_err(ndev, "TX buf %d status: 0x%x.\n", i, sts);
+		}
+	}
+
+	loongson_canfd_disable_interrupts(priv);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * loongson_canfd_chip_stop() - Driver stop routine
+ * @ndev: Pointer to net_device structure
+ *
+ * This is the drivers stop routine. It will disable the interrupts and
+ * disable the controller.
+ */
+static void loongson_canfd_chip_stop(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+
+	/* Disable interrupts and disable CAN */
+	loongson_canfd_disable_interrupts(priv);
+	regmap_update_bits(priv->regmap, LOONGSON_CANFD_CONF, REG_CONF_ENA, 0);
+
+	priv->can.state = CAN_STATE_STOPPED;
+}
+
+/**
+ * loongson_canfd_open() - Driver open routine
+ * @ndev: Pointer to net_device structure
+ *
+ * This is the driver open routine.
+ * Return: 0 on success and failure value on error
+ */
+static int loongson_canfd_open(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+	int ret;
+
+	loongson_canfd_reset(ndev);
+
+	/* Common open */
+	ret = open_candev(ndev);
+	if (ret) {
+		netdev_warn(ndev, "open_candev failed!\n");
+		return ret;
+	}
+
+	napi_enable(&priv->napi);
+	ret = request_irq(ndev->irq, loongson_canfd_interrupt, IRQF_SHARED, ndev->name, ndev);
+	if (ret < 0) {
+		netdev_err(ndev, "irq allocation for CAN failed\n");
+		goto exit_napi_disable;
+	}
+
+	ret = loongson_canfd_chip_start(ndev);
+	if (ret < 0) {
+		netdev_err(ndev, "loongson_canfd_chip_start failed!\n");
+		goto exit_free_irq;
+	}
+
+	netdev_info(ndev, "loongson_canfd_device registered\n");
+	netif_start_queue(ndev);
+
+	return 0;
+
+exit_free_irq:
+	free_irq(ndev->irq, ndev);
+exit_napi_disable:
+	napi_disable(&priv->napi);
+	close_candev(ndev);
+	return ret;
+}
+
+/**
+ * loongson_canfd_close() - Driver close routine
+ * @ndev: Pointer to net_device structure
+ *
+ * Return: 0 always
+ */
+static int loongson_canfd_close(struct net_device *ndev)
+{
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+
+	netif_stop_queue(ndev);
+	napi_disable(&priv->napi);
+	loongson_canfd_chip_stop(ndev);
+	free_irq(ndev->irq, ndev);
+	close_candev(ndev);
+
+	return 0;
+}
+
+static const struct net_device_ops loongson_canfd_netdev_ops = {
+	.ndo_open       = loongson_canfd_open,
+	.ndo_stop       = loongson_canfd_close,
+	.ndo_start_xmit = loongson_canfd_start_xmit,
+};
+
+static const struct ethtool_ops loongson_canfd_ethtool_ops = {
+	.get_ts_info = ethtool_op_get_ts_info,
+};
+
+static const struct regmap_range loongson_canfd_reg_table_wr_range[] = {
+	regmap_reg_range(LOONGSON_CANFD_DEVICE_ID, LOONGSON_CANFD_CONF),
+	regmap_reg_range(LOONGSON_CANFD_CMD, LOONGSON_CANFD_CMD),
+	regmap_reg_range(LOONGSON_CANFD_INT_STAT, LOONGSON_CANFD_ERL),
+	regmap_reg_range(LOONGSON_CANFD_CTR_PRES, LOONGSON_CANFD_CTR_PRES),
+	regmap_reg_range(LOONGSON_CANFD_SSP_CFG, LOONGSON_CANFD_SSP_CFG),
+	regmap_reg_range(LOONGSON_CANFD_TS, LOONGSON_CANFD_FLT_CTRL),
+	regmap_reg_range(LOONGSON_CANFD_TX_CMD, LOONGSON_CANFD_TX_DATA_18),
+};
+
+static const struct regmap_range loongson_canfd_reg_table_rd_range[] = {
+	regmap_reg_range(LOONGSON_CANFD_DEVICE_ID, LOONGSON_CANFD_STAT),
+	regmap_reg_range(LOONGSON_CANFD_INT_STAT, LOONGSON_CANFD_BRE),
+	regmap_reg_range(LOONGSON_CANFD_ERR_CAPT, LOONGSON_CANFD_TX_STAT),
+	regmap_reg_range(LOONGSON_CANFD_TX_SEL, LOONGSON_CANFD_TX_DATA_18),
+};
+
+static const struct regmap_access_table loongson_canfd_reg_table_wr = {
+	.yes_ranges = loongson_canfd_reg_table_wr_range,
+	.n_yes_ranges = ARRAY_SIZE(loongson_canfd_reg_table_wr_range),
+};
+
+static const struct regmap_access_table loongson_canfd_reg_table_rd = {
+	.yes_ranges = loongson_canfd_reg_table_rd_range,
+	.n_yes_ranges = ARRAY_SIZE(loongson_canfd_reg_table_rd_range),
+};
+
+static bool loongson_canfd_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case LOONGSON_CANFD_MODE:
+	case LOONGSON_CANFD_CONF:
+	case LOONGSON_CANFD_STAT:
+	case LOONGSON_CANFD_INT_STAT:
+	case LOONGSON_CANFD_INT_ENA:
+	case LOONGSON_CANFD_INT_MASK:
+	case LOONGSON_CANFD_ERL:
+	case LOONGSON_CANFD_FSTAT:
+	case LOONGSON_CANFD_ERC:
+	case LOONGSON_CANFD_ERR_CAPT:
+	case LOONGSON_CANFD_ALC:
+	case LOONGSON_CANFD_TRV_DLY:
+	case LOONGSON_CANFD_TX_FR_CNT:
+	case LOONGSON_CANFD_RX_STAT:
+	case LOONGSON_CANFD_RX_DATA:
+	case LOONGSON_CANFD_TX_STAT:
+	case LOONGSON_CANFD_TX_SEL:
+		return true;
+	default:
+		return false;
+	};
+}
+
+static const struct regmap_config loongson_cangfd_regmap = {
+	.reg_bits	= 32,
+	.reg_stride	= 4,
+	.val_bits	= 32,
+	.wr_table	= &loongson_canfd_reg_table_wr,
+	.rd_table	= &loongson_canfd_reg_table_rd,
+	.volatile_reg	= loongson_canfd_volatile_reg,
+	.max_register	= LOONGSON_CANFD_TX_DATA_18,
+	.cache_type	= REGCACHE_MAPLE,
+};
+
+static int loongson_canfd_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct loongson_canfd_priv *priv;
+	struct net_device *ndev;
+	struct regmap *regmap;
+	struct resource *res;
+	void __iomem *base;
+	int ret = 0, irq;
+	u32 clk_rate;
+
+	base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	regmap = devm_regmap_init_mmio(dev, base, &loongson_cangfd_regmap);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	ret = device_property_read_u32(dev, "clock-frequency", &clk_rate);
+	if (ret)
+		return dev_err_probe(dev, ret, "Missing clock-frequency property\n");
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	/* Create a CAN device instance */
+	ndev = alloc_candev(sizeof(*priv), LOONGSON_CANFD_TXBUF_NUM);
+	if (!ndev)
+		return -ENOMEM;
+
+	priv = netdev_priv(ndev);
+	spin_lock_init(&priv->tx_lock);
+	priv->regmap = regmap;
+	priv->res = res;
+
+	priv->can.clock.freq = clk_rate;
+	priv->can.bittiming_const = &loongson_canfd_bit_timing;
+	priv->can.fd.data_bittiming_const = &loongson_canfd_bit_timing_data;
+	priv->can.fd.tdc_const = &loongson_canfd_tdc_data;
+
+	priv->can.fd.do_set_data_bittiming = loongson_canfd_set_data_bittiming;
+	priv->can.fd.do_get_auto_tdcv = loongson_canfd_get_auto_tdcv;
+	priv->can.do_set_mode = loongson_canfd_do_set_mode;
+	priv->can.do_set_bittiming = loongson_canfd_set_bittiming;
+	priv->can.do_get_berr_counter = loongson_canfd_get_berr_counter;
+
+	priv->can.ctrlmode_supported = CAN_CTRLMODE_LOOPBACK | CAN_CTRLMODE_LISTENONLY |
+				       CAN_CTRLMODE_ONE_SHOT | CAN_CTRLMODE_BERR_REPORTING |
+				       CAN_CTRLMODE_FD | CAN_CTRLMODE_PRESUME_ACK |
+				       CAN_CTRLMODE_FD_NON_ISO | CAN_CTRLMODE_TDC_AUTO |
+				       CAN_CTRLMODE_CC_LEN8_DLC;
+
+	ndev->irq = irq;
+	ndev->flags |= IFF_ECHO;	/* We support local echo */
+	platform_set_drvdata(pdev, ndev);
+	ndev->netdev_ops = &loongson_canfd_netdev_ops;
+	ndev->ethtool_ops = &loongson_canfd_ethtool_ops;
+	SET_NETDEV_DEV(ndev, dev);
+
+	netif_napi_add(ndev, &priv->napi, loongson_canfd_rx_napi);
+
+	ret = register_candev(ndev);
+	if (ret) {
+		dev_err(dev, "register_candev failed with %d\n", ret);
+		goto err_candev_free;
+	}
+
+	return 0;
+
+err_candev_free:
+	netif_napi_del(&priv->napi);
+	free_candev(ndev);
+	return ret;
+}
+
+/**
+ * loongson_canfd_remove - Unregister the device after releasing the resources
+ * @pdev: Handle to the platform device structure
+ *
+ * This function frees all the resources allocated to the device.
+ */
+static void loongson_canfd_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct loongson_canfd_priv *priv = netdev_priv(ndev);
+
+	unregister_candev(ndev);
+	netif_napi_del(&priv->napi);
+	free_candev(ndev);
+}
+
+static const struct acpi_device_id loongson_canfd_acpi_match[] = {
+	{ .id = "LOON0015" },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, loongson_canfd_acpi_match);
+
+static struct platform_driver loongson_canfd_driver = {
+	.probe  = loongson_canfd_probe,
+	.remove = loongson_canfd_remove,
+	.driver = {
+		.name = DEV_NAME,
+		.acpi_match_table = loongson_canfd_acpi_match,
+	},
+};
+module_platform_driver(loongson_canfd_driver);
+
+MODULE_AUTHOR("Loongson Technology Corporation Limited");
+MODULE_DESCRIPTION("Loongson CAN-FD Controller driver");
+MODULE_LICENSE("GPL");
-- 
2.52.0