Re: [PATCH 0/3] net: ntb_netdev: Add Multi-queue support

On 2/24/26 8:36 PM, Koichiro Den wrote:
> On Tue, Feb 24, 2026 at 09:20:35AM -0700, Dave Jiang wrote:
>>
>>
>> On 2/24/26 8:28 AM, Koichiro Den wrote:
>>> Hi,
>>>
>>> ntb_netdev currently hard-codes a single NTB transport queue pair, which
>>> means the datapath effectively runs as a single-queue netdev regardless
>>> of available CPUs / parallel flows.
>>>
>>> The longer-term motivation here is throughput scale-out: allow
>>> ntb_netdev to grow beyond the single-QP bottleneck and make it possible
>>> to spread TX/RX work across multiple queue pairs as link speeds and core
>>> counts keep increasing.
>>>
>>> Multi-queue also unlocks the standard networking knobs on top of it. In
>>> particular, once the device exposes multiple TX queues, qdisc/tc can
>>> steer flows/traffic classes into different queues (via
>>> skb->queue_mapping), enabling per-flow/per-class scheduling and QoS in a
>>> familiar way.
>>>
>>> This series is a small plumbing step towards that direction:
>>>
>>>   1) Introduce a per-queue context object (struct ntb_netdev_queue) and
>>>      move queue-pair state out of struct ntb_netdev. Probe creates queue
>>>      pairs in a loop and configures the netdev queue counts to match the
>>>      number that was successfully created.
>>>
>>>   2) Expose ntb_num_queues as a module parameter to request multiple
>>>      queue pairs at probe time. The value is clamped to 1..64 and kept
>>>      read-only for now (no runtime reconfiguration).
>>>
>>>   3) Report the active queue-pair count via ethtool -l (get_channels),
>>>      so users can confirm the device configuration from user space.
>>>
>>> Compatibility:
>>>   - Default remains ntb_num_queues=1, so behaviour is unchanged unless
>>>     the user explicitly requests more queues.
>>>
>>> Kernel base:
>>>   - ntb-next latest:
>>>     commit 7b3302c687ca ("ntb_hw_amd: Fix incorrect debug message in link
>>>                           disable path")
>>>
>>> Usage (example):
>>>   - modprobe ntb_netdev ntb_num_queues=<N> # Patch 2 takes care of it
>>>   - ethtool -l <ifname> # Patch 3 takes care of it
>>>
>>> Patch summary:
>>>   1/3 net: ntb_netdev: Introduce per-queue context
>>>   2/3 net: ntb_netdev: Make queue pair count configurable
>>>   3/3 net: ntb_netdev: Expose queue pair count via ethtool -l
>>>
>>> Testing / results:
>>>   Environment / command line:
>>>     - 2x R-Car S4 Spider boards
>>>       "Kernel base" (see above) + this series
>>>     - For TCP load:
>>>       [RC] $ sudo iperf3 -s
>>>       [EP] $ sudo iperf3 -Z -c ${SERVER_IP} -l 65480 -w 512M -P 4
>>>     - For UDP load:
>>>       [RC] $ sudo iperf3 -s
>>>       [EP] $ sudo iperf3 -ub0 -c ${SERVER_IP} -l 65480 -w 512M -P 4
>>>
>>>   Before (without this series):
>>>       TCP / UDP : 602 Mbps / 598 Mbps
>>>
>>>   Before (ntb_num_queues=1):
>>>       TCP / UDP : 588 Mbps / 605 Mbps
>>
>> What accounts for the dip in TCP performance?
> 
> I believe this is within normal run-to-run variance. To be sure, I repeated the
> TCP tests multiple times. The aggregated results are:
> 
>   +------+----------+------------------+------------------+
>   |      | Baseline | ntb_num_queues=1 | ntb_num_queues=2 |
>   +------+----------+------------------+------------------+
>   | Mean | 599.5    | 595.2 (-0.7%)    | 600.4 (+0.2%)    |
>   | Min  | 590      | 590   (+0.0%)    | 593   (+0.5%)    |
>   | Max  | 605      | 604   (-0.2%)    | 605   (+0.0%)    |
>   | Med  | 602      | 593              | 601.5            |
>   | SD   | 5.84     | 6.01             | 4.12             |
>   +------+----------+------------------+------------------+
> 
> On my setup (2x R-Car S4 Spider), I do not observe any statistically meaningful
> improvement or degradation. For completeness, here is the raw data:
> 
>               .----------------------------- Baseline (without this series)
>               :           .----------------- ntb_num_queues=1
>               :           :            .---- ntb_num_queues=2
>               :           :            :
>     #1     601 Mbps    604 Mbps     601 Mbps
>     #2     604 Mbps    604 Mbps     603 Mbps
>     #3     592 Mbps    590 Mbps     600 Mbps
>     #4     593 Mbps    593 Mbps     603 Mbps
>     #5     605 Mbps    591 Mbps     605 Mbps
>     #6     590 Mbps    603 Mbps     602 Mbps
>     #7     605 Mbps    590 Mbps     596 Mbps
>     #8     598 Mbps    594 Mbps     593 Mbps
>     #9     603 Mbps    590 Mbps     605 Mbps
>     #10    604 Mbps    593 Mbps     596 Mbps
> 
> To see a tangible performance gain, another patch series I submitted yesterday
> is also relevant:
> 
>   [PATCH 00/10] NTB: epf: Enable per-doorbell bit handling while keeping legacy offset
>   https://lore.kernel.org/all/[email protected]/
> 
> With that series applied as well, and with irq smp_affinity properly adjusted,
> the results become:
> 
>   After (ntb_num_queues=2 + the other series also applied):
>       TCP / UDP : 1.15 Gbps / 1.18 Gbps
> 
> In that sense, that series is also important groundwork from a performance
> perspective. Since that work touches NTB-tree code, I'd appreciate it if you
> could also have a look at that series.
> 
> Side note: R-Car S4 Spider has limited BAR resources. Although BAR2 is
> resizable, ~2 MiB appears to be the practical ceiling for arbitrary mappings in
> this setup, so I haven't tested larger ntb_num_queues=<N> values. On platforms
> with more BAR space, sufficient CPUs for memcpy, or sufficent DMA channels for
> DMA memcpy available to ntb_transport, further scaling with larger <N> values
> should be possible.

Thanks for the data. I'll take a look at the other series.

> 
> Thanks,
> Koichiro
> 
>>
>>>
>>>   After (ntb_num_queues=2):
>>>       TCP / UDP : 602 Mbps / 598 Mbps
>>>
>>>   Notes:
>>>     In my current test environment, enabling multiple queue pairs does
>>>     not improve throughput. The receive-side memcpy in ntb_transport is
>>>     the dominant cost and limits scaling at present.
>>>
>>>     Still, this series lays the groundwork for future scaling, for
>>>     example once a transport backend is introduced that avoids memcpy
>>>     to/from PCI memory space on both ends (see the superseded RFC
>>>     series:
>>>     https://lore.kernel.org/all/[email protected]/).
>>>
>>>
>>> Best regards,
>>> Koichiro
>>>
>>> Koichiro Den (3):
>>>   net: ntb_netdev: Introduce per-queue context
>>>   net: ntb_netdev: Make queue pair count configurable
>>>   net: ntb_netdev: Expose queue pair count via ethtool -l
>>>
>>>  drivers/net/ntb_netdev.c | 326 +++++++++++++++++++++++++++------------
>>>  1 file changed, 228 insertions(+), 98 deletions(-)
>>>
>>
>> for the series
>> Reviewed-by: Dave Jiang <[email protected]>
>>