Re: [REGRESSION] PCIe/qcom: on-board WCN7850 link stuck in Polling on X1E80100 (Surface Pro 11)

On 8/18/26 13:13, Manivannan Sadhasivam wrote:
> + Krishna

Hmm, nothing happened here. Or did it and I just missed it?

Krishna, it seemed Mani thought you might haven an idea what's wrong. Do
you do by chance?

If not, I guess Franzelverbier might need to bisect this.

Ciao, Thorsten

> On Fri, Jul 31, 2026 at 02:22:25PM +0200, franzelverbier wrote:
>> Hi,
>>
>> On a Microsoft Surface Pro 11 (Snapdragon X Elite, X1E80100, board
>> x1e80100-microsoft-denali-oled), the on-board WCN7850 Wi-Fi PCIe link
>> no longer trains on linux-next. It works on 6.17.
>>
>>   Good: v6.17
>>   Bad:  next-20260721, next-20260723
>>
>> #regzbot introduced: v6.17..next-20260721
>> #regzbot title: PCIe/qcom: WCN7850 link stuck in Polling on X1E80100
>>
>> The device sits behind PCIe controller 1c08000.pci (pcie4,
>> qcom,pcie-x1e80100, gen3x2) and has no PERST# GPIO -- it is
>> power-sequenced via wcn7850-pmu / pwrseq.
>>
>> Symptom
>> =======
>>
>>   qcom-pcie 1c08000.pci: Device found, but not active
>>   qcom-pcie 1c08000.pci: PCI host bridge to bus 0004:00
>>
>> dw_pcie_wait_for_link() finds the LTSSM in POLL_ACTIVE/POLL_COMPLIANCE
>> and returns -EIO. The endpoint 0004:01:00.0 is never enumerated, ath12k
>> never probes, and there is no wlan interface. On 6.17 the same
>> controller trains at ~0.6 s and ath12k probes normally.
>>
>> Ruled out: the chip is powered, and power control is bound
>> ==========================================================
>>
>> - Bluetooth on the same WCN7850 (UART) comes up fine, so the PMU and
>>   regulators are on.
>>
>> - pwrseq_qcom_wcn is loaded, and pci-pwrctrl-pwrseq is bound to the
>>   platform device 1c08000.pci:pcie@0:wifi@0 (compatible pci17cb,1107 is
>>   present in pwrseq_pwrctrl_of_match[]). The vddaon-supply
>>   validate_device() check passes.
>>
>> Ruled out: not a device-tree regression
>> =======================================
>>
>> The wifi@0, &pcie4 and &pcie4_phy nodes are equivalent between the 6.17
>> and 7.2 device trees -- same supplies, same compatibles. The only
>> difference in wifi@0 is "disable-rfkill;" (6.17), which is
>> post-enumeration ath12k behaviour and cannot affect link training.
>>
>> What changed
>> ============
>>
>> qcom_pcie_host_init() was reworked around the pci-pwrctrl framework,
>> and qcom_pcie_start_link() now calls qcom_pcie_common_set_equalization()
>> -- absent in 6.17 -- before enabling the LTSSM.
>>
>> Finding 1: Gen3 equalization prevents link training
>> ===================================================
>>
>> Forcing the port to Gen1 makes the link train and ath12k probe:
>>
>>   &pcie4 { max-link-speed = <1>; status = "okay"; };
>>
>>   qcom-pcie 1c08000.pci: PCIe Gen.1 x2 link up
>>   ath12k_wifi7_pci 0004:01:00.0: Wi-Fi 7 Hardware name: wcn7850 hw2.0
>>
>> qcom_pcie_common_set_equalization() only programs GEN3_EQ_* for speeds
>>> = 8GT, so max-link-speed=<1> skips it entirely, reproducing the 6.17
>> behaviour of no EQ programming.
>>
>> Note this is not a wrong preset value. The presets come from DT via
>> of_pci_get_equalization_presets() and are applied by the DWC host core.
>> In hamoa.dtsi:
>>
>>   pcie4  (pci@1c08000, gen3x2, on-board WCN7850)
>>     eq-presets-8gts = /bits/ 16 <0x5555 0x5555>;
>>
>>   pcie6a (pci@1bf8000, NVMe, gen4x4)
>>     eq-presets-8gts = /bits/ 16 <0x5555 0x5555 0x5555 0x5555>;
>>
>> Both use the same per-lane preset 0x5555. The NVMe port trains at Gen4
>> fine; only the WCN7850 port fails. So the WCN7850 endpoint specifically
>> cannot complete Gen3 equalization with these presets on this
>> controller, while an NVMe SSD on the same SoC can.
>>
>> The board DTS (x1-microsoft-denali.dtsi, also in mainline) leaves
>> &pcie4 as status = "okay" with no per-port override, so it inherits the
>> SoC preset.
>>
>> Finding 2: an LTSSM re-kick does not recover the link
>> =====================================================
>>
>> Even at Gen1, the link does not train on the first attempt at boot
>> (~4 s); in one instance it only came up much later via a pciehp slot
>> event. An experimental retry in qcom_pcie_start_link() toggling
>> PARF_LTSSM.LTSSM_EN (clear/set) for up to 30 s never recovered the
>> link.
>>
>> That suggests the endpoint needs a full power/reset re-sequence
>> (pwrseq) to leave the failed state, not just an LTSSM restart -- i.e.
>> the pwrseq power-on may be racing link bring-up at boot for PERST-less
>> on-board devices.
>>
>> When the link does come up late (fragmented CMA, tight PCI windows),
>> secondary symptoms appear that are absent on a clean boot-time
>> bring-up:
>>
>>   ath12k ... qmi dma allocation failed
>>   BAR 0 ... failed to assign
>>   rfkill ... Hard blocked: yes
>>
>> Questions
>> =========
>>
>> 1. Are the qcom_pcie_common_set_equalization() Gen3 EQ presets expected
>>    to be safe for a gen3x2 PHY driving an on-board WCN7850? They
>>    prevent link training here, and skipping them (Gen1) works.
>>
>> 2. Is pci-pwrctrl/pwrseq power-on racing link training at boot for
>>    on-board devices with no PERST# GPIO, such that the endpoint is not
>>    ready on the first LTSSM attempt and cannot be recovered by an LTSSM
>>    re-kick?
>>
>> I have not bisected to a single commit yet -- the range above is v6.17
>> to next-20260721. I am happy to bisect, test patches, or dump any
>> register on this hardware; rebuilding is a short loop here.
>>
>> Environment
>> ===========
>>
>> linux-next next-20260723, CONFIG_PCIE_QCOM=y, CONFIG_CMA_SIZE_MBYTES=128,
>> ath12k, board x1e80100-microsoft-denali-oled, Arch Linux ARM (aarch64).
>>
>> Thanks,
>> franzelverbier
>