Re: [PATCH 3/5] PCI: sg2042: Add Sophgo SG2042 PCIe driver

On Thu, Aug 28, 2025 at 10:17:40AM GMT, Chen Wang wrote:
> From: Chen Wang <[email protected]>
> 
> Add support for PCIe controller in SG2042 SoC. The controller
> uses the Cadence PCIe core programmed by pcie-cadence*.c. The
> PCIe controller will work in host mode only.
> 

Supported data rate, lanes etc...

> Signed-off-by: Chen Wang <[email protected]>
> ---
>  drivers/pci/controller/cadence/Kconfig       |  12 ++
>  drivers/pci/controller/cadence/Makefile      |   1 +
>  drivers/pci/controller/cadence/pcie-sg2042.c | 134 +++++++++++++++++++
>  3 files changed, 147 insertions(+)
>  create mode 100644 drivers/pci/controller/cadence/pcie-sg2042.c
> 
> diff --git a/drivers/pci/controller/cadence/Kconfig b/drivers/pci/controller/cadence/Kconfig
> index 666e16b6367f..b1f1941d5208 100644
> --- a/drivers/pci/controller/cadence/Kconfig
> +++ b/drivers/pci/controller/cadence/Kconfig
> @@ -42,6 +42,17 @@ config PCIE_CADENCE_PLAT_EP
>  	  endpoint mode. This PCIe controller may be embedded into many
>  	  different vendors SoCs.
>  
> +config PCIE_SG2042

PCIE_SG2042_HOST

> +	bool "Sophgo SG2042 PCIe controller (host mode)"

Since this driver doesn't implement irqchip, you should make it tristate and as
a module.

> +	depends on ARCH_SOPHGO || COMPILE_TEST
> +	depends on OF

	depends on OF && (ARCH_SOPHGO || COMPILE_TEST)

> +	depends on PCI_MSI
> +	select PCIE_CADENCE_HOST
> +	help
> +	  Say Y here if you want to support the Sophgo SG2042 PCIe platform
> +	  controller in host mode. Sophgo SG2042 PCIe controller uses Cadence
> +	  PCIe core.
> +
>  config PCI_J721E
>  	tristate
>  	select PCIE_CADENCE_HOST if PCI_J721E_HOST != n
> @@ -67,4 +78,5 @@ config PCI_J721E_EP
>  	  Say Y here if you want to support the TI J721E PCIe platform
>  	  controller in endpoint mode. TI J721E PCIe controller uses Cadence PCIe
>  	  core.
> +
>  endmenu
> diff --git a/drivers/pci/controller/cadence/Makefile b/drivers/pci/controller/cadence/Makefile
> index 9bac5fb2f13d..4df4456d9539 100644
> --- a/drivers/pci/controller/cadence/Makefile
> +++ b/drivers/pci/controller/cadence/Makefile
> @@ -4,3 +4,4 @@ obj-$(CONFIG_PCIE_CADENCE_HOST) += pcie-cadence-host.o
>  obj-$(CONFIG_PCIE_CADENCE_EP) += pcie-cadence-ep.o
>  obj-$(CONFIG_PCIE_CADENCE_PLAT) += pcie-cadence-plat.o
>  obj-$(CONFIG_PCI_J721E) += pci-j721e.o
> +obj-$(CONFIG_PCIE_SG2042) += pcie-sg2042.o
> diff --git a/drivers/pci/controller/cadence/pcie-sg2042.c b/drivers/pci/controller/cadence/pcie-sg2042.c
> new file mode 100644
> index 000000000000..fe434dc2967e
> --- /dev/null
> +++ b/drivers/pci/controller/cadence/pcie-sg2042.c
> @@ -0,0 +1,134 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * pcie-sg2042 - PCIe controller driver for Sophgo SG2042 SoC
> + *
> + * Copyright (C) 2025 Sophgo Technology Inc.
> + * Copyright (C) 2025 Chen Wang <[email protected]>
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/of.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +
> +#include "pcie-cadence.h"
> +
> +/*
> + * SG2042 only support 4-byte aligned access, so for the rootbus (i.e. to read
> + * the Root Port itself, read32 is required. For non-rootbus (i.e. to read
> + * the PCIe peripheral registers, supports 1/2/4 byte aligned access, so
> + * directly using read should be fine.
> + *
> + * The same is true for write.
> + */
> +static int sg2042_pcie_config_read(struct pci_bus *bus, unsigned int devfn,
> +				   int where, int size, u32 *value)
> +{
> +	if (pci_is_root_bus(bus))
> +		return pci_generic_config_read32(bus, devfn, where, size,
> +						 value);
> +
> +	return pci_generic_config_read(bus, devfn, where, size, value);
> +}
> +
> +static int sg2042_pcie_config_write(struct pci_bus *bus, unsigned int devfn,
> +				    int where, int size, u32 value)
> +{
> +	if (pci_is_root_bus(bus))
> +		return pci_generic_config_write32(bus, devfn, where, size,
> +						  value);
> +
> +	return pci_generic_config_write(bus, devfn, where, size, value);
> +}
> +
> +static struct pci_ops sg2042_pcie_host_ops = {
> +	.map_bus	= cdns_pci_map_bus,
> +	.read		= sg2042_pcie_config_read,
> +	.write		= sg2042_pcie_config_write,
> +};
> +
> +static int sg2042_pcie_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct pci_host_bridge *bridge;
> +	struct cdns_pcie *pcie;
> +	struct cdns_pcie_rc *rc;
> +	int ret;
> +
> +	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
> +	if (!pcie)
> +		return -ENOMEM;
> +
> +	bridge = devm_pci_alloc_host_bridge(dev, sizeof(*rc));
> +	if (!bridge) {
> +		dev_err(dev, "Failed to alloc host bridge!\n");

Use dev_err_probe() here and below.

> +		return -ENOMEM;
> +	}
> +
> +	bridge->ops = &sg2042_pcie_host_ops;
> +
> +	rc = pci_host_bridge_priv(bridge);
> +	pcie = &rc->pcie;

You are setting drvdata only below.

> +	pcie->dev = dev;
> +
> +	platform_set_drvdata(pdev, pcie);
> +
> +	pm_runtime_enable(dev);
> +
> +	ret = pm_runtime_get_sync(dev);
> +	if (ret < 0) {
> +		dev_err(dev, "pm_runtime_get_sync failed\n");
> +		goto err_get_sync;
> +	}
> +

Why do you need pm_runtime_get_sync()? DT binding doesn't provide a
power-domain, so you just need:

	pm_runtime_set_active()
        pm_runtime_no_callbacks()
        devm_pm_runtime_enable()

> +	ret = cdns_pcie_init_phy(dev, pcie);
> +	if (ret) {
> +		dev_err(dev, "Failed to init phy!\n");
> +		goto err_get_sync;
> +	}
> +
> +	ret = cdns_pcie_host_setup(rc);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to setup host!\n");
> +		goto err_host_setup;
> +	}
> +
> +	return 0;
> +
> +err_host_setup:
> +	cdns_pcie_disable_phy(pcie);
> +
> +err_get_sync:
> +	pm_runtime_put(dev);
> +	pm_runtime_disable(dev);
> +
> +	return ret;
> +}
> +
> +static void sg2042_pcie_shutdown(struct platform_device *pdev)
> +{
> +	struct cdns_pcie *pcie = platform_get_drvdata(pdev);
> +	struct device *dev = &pdev->dev;
> +
> +	cdns_pcie_disable_phy(pcie);
> +
> +	pm_runtime_put(dev);
> +	pm_runtime_disable(dev);

You don't need these as per my above suggestion.

> +}
> +
> +static const struct of_device_id sg2042_pcie_of_match[] = {
> +	{ .compatible = "sophgo,sg2042-pcie-host" },
> +	{},
> +};
> +
> +static struct platform_driver sg2042_pcie_driver = {
> +	.driver = {
> +		.name		= "sg2042-pcie",
> +		.of_match_table	= sg2042_pcie_of_match,
> +		.pm		= &cdns_pcie_pm_ops,
> +	},
> +	.probe		= sg2042_pcie_probe,

Why no remove()?

- Mani

-- 
மணிவண்ணன் சதாசிவம்