[PATCH 3/4] riscv: dts: spacemit: k3: add USB3 B and C controllers for Pico-ITX board

The SpacemiT K3 has 4 USB3 controllers labelled A to D.

On the K3 Pico-ITX board, the controllers B and C are used in USB 2 mode
only respectively for the M.2 B-Key slot and for the RTL8852BE Bluetooth
controller.

Add the two controller nodes and the two corresponding USB2 PHY nodes
(the PCIe/USB3 combo PHY driver is not yet merged) and enable them on
the K3 Pico-ITX board.

Signed-off-by: Aurelien Jarno <[email protected]>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 18 ++++++
 arch/riscv/boot/dts/spacemit/k3.dtsi         | 65 ++++++++++++++++++++
 2 files changed, 83 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index 4aa7d56fb7568..011a35e6372e1 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -325,3 +325,21 @@ hub@1 {
 &usb2_phy {
 	status = "okay";
 };
+
+&usb3b {
+	maximum-speed = "high-speed";
+	status = "okay";
+};
+
+&usb3b_u2phy {
+	status = "okay";
+};
+
+&usb3c {
+	maximum-speed = "high-speed";
+	status = "okay";
+};
+
+&usb3c_u2phy {
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
index fc46e34465e47..b14bd8a164537 100644
--- a/arch/riscv/boot/dts/spacemit/k3.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
@@ -7,6 +7,7 @@
 #include <dt-bindings/clock/spacemit,k3-clocks.h>
 #include <dt-bindings/reset/spacemit,k3-resets.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
 
 /dts-v1/;
 
@@ -438,6 +439,70 @@ soc: soc {
 		dma-noncoherent;
 		ranges;
 
+		usb3b: usb@81400000 {
+			compatible = "spacemit,k3-dwc3";
+			reg = <0x0 0x81400000 0x0 0x10000>;
+			interrupts = <125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&saplic>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTB_BUS>;
+			clock-names = "usbdrd30";
+			resets = <&syscon_apmu RESET_APMU_USB3_B_AHB>,
+				 <&syscon_apmu RESET_APMU_USB3_B_VCC>,
+				 <&syscon_apmu RESET_APMU_USB3_B_PHY>;
+			reset-names = "ahb", "vcc", "phy";
+			phys = <&usb3b_u2phy>;
+			phy-names = "usb2-phy";
+			phy_type = "utmi";
+			snps,dis_enblslpm_quirk;
+			snps,dis_u2_susphy_quirk;
+			snps,dis_u3_susphy_quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,parkmode-disable-ss-quirk;
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		usb3b_u2phy: phy@81500000 {
+			compatible = "spacemit,k3-usb2-phy";
+			reg = <0x0 0x81500000 0x0 0x200>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTB_BUS>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		usb3c: usb@81700000 {
+			compatible = "spacemit,k3-dwc3";
+			reg = <0x0 0x81700000 0x0 0x10000>;
+			interrupts = <148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&saplic>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTC_BUS>;
+			clock-names = "usbdrd30";
+			resets = <&syscon_apmu RESET_APMU_USB3_C_AHB>,
+				 <&syscon_apmu RESET_APMU_USB3_C_VCC>,
+				 <&syscon_apmu RESET_APMU_USB3_C_PHY>;
+			reset-names = "ahb", "vcc", "phy";
+			phys = <&usb3c_u2phy>;
+			phy-names = "usb2-phy";
+			phy_type = "utmi";
+			snps,dis_enblslpm_quirk;
+			snps,dis_u2_susphy_quirk;
+			snps,dis_u3_susphy_quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,parkmode-disable-ss-quirk;
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		usb3c_u2phy: phy@81800000 {
+			compatible = "spacemit,k3-usb2-phy";
+			reg = <0x0 0x81800000 0x0 0x200>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTC_BUS>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		usb2_host: usb@c0a00000 {
 			compatible = "spacemit,k3-dwc3";
 			reg = <0x0 0xc0a00000 0x0 0x10000>;
-- 
2.53.0