[PATCH v2 2/2] riscv: dts: spacemit: k3: Add PCIe device node

Add all PCIe device node for Spacemit K3.

Signed-off-by: Inochi Amaoto <[email protected]>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts |  38 ++++
 arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi |  33 ++++
 arch/riscv/boot/dts/spacemit/k3.dtsi         | 195 +++++++++++++++++++
 3 files changed, 266 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index 2a6d35a64d5c..1eb5abbc61f9 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -205,6 +205,44 @@ phy0: phy@1 {
 	};
 };
 
+&pcie0_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_0_cfg>;
+	num-lanes = <4>;
+	status = "okay";
+
+	pcie@0 {
+		vpcie3v3-supply = <&reg_aux_vcc3v3>;
+		phys = <&combophy 0 PHY_TYPE_PCIE>,
+		       <&combophy 1 PHY_TYPE_PCIE>;
+	};
+};
+
+&pcie2_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie2_0_cfg>;
+	num-lanes = <2>;
+	status = "okay";
+
+	pcie@0 {
+		vpcie3v3-supply = <&reg_aux_vcc3v3>;
+		phys = <&combophy 2 PHY_TYPE_PCIE>,
+		       <&combophy 3 PHY_TYPE_PCIE>;
+	};
+};
+
+&pcie4_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie4_0_cfg>;
+	num-lanes = <1>;
+	status = "okay";
+
+	pcie@0 {
+		vpcie3v3-supply = <&reg_aux_vcc3v3>;
+		phys = <&combophy 5 PHY_TYPE_PCIE>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_0_cfg>;
diff --git a/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
index 3ee1471f3798..68aa21a5279f 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
@@ -689,4 +689,37 @@ uart0-0-pins {
 			drive-strength = <25>;
 		};
 	};
+
+	pcie0_0_cfg: pcie0-0-cfg {
+		pcie0-0-pins {
+			pinmux = <K3_PADCONF(79, 5)>,   /* pcie0 perst */
+				 <K3_PADCONF(81, 5)>;	/* pcie0 clkreq */
+
+			bias-pull-up = <1>;
+			drive-strength = <33>;
+			power-source = <1800>;
+		};
+	};
+
+	pcie2_0_cfg: pcie2-0-cfg {
+		pcie2-0-pins {
+			pinmux = <K3_PADCONF(25, 4)>,	/* pcie2 perst */
+				 <K3_PADCONF(27, 4)>;	/* pcie2 clkreq */
+
+			drive-strength = <38>;
+			power-source = <3300>;
+		};
+	};
+
+	pcie4_0_cfg: pcie4-0-cfg {
+		pcie4-0-pins {
+			pinmux = <K3_PADCONF(76, 5)>,	/* pcie4 perst */
+				 <K3_PADCONF(77, 5)>,	/* pcie4 wake */
+				 <K3_PADCONF(78, 5)>;	/* pcie4 clkreq */
+
+			bias-pull-up = <1>;
+			drive-strength = <33>;
+			power-source = <1800>;
+		};
+	};
 };
diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
index 7863ab7dd308..314dea88b4a4 100644
--- a/arch/riscv/boot/dts/spacemit/k3.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
@@ -439,6 +439,201 @@ soc: soc {
 		dma-noncoherent;
 		ranges;
 
+		pcie0_rc: pcie@80000000 {
+			compatible = "spacemit,k3-pcie";
+			reg = <0x0 0x80000000 0x0 0x00001000>,
+			      <0x0 0x80300000 0x0 0x00003f20>,
+			      <0x11 0x00000000 0x0 0x00010000>,
+			      <0x0 0x82900000 0x0 0x00001000>,
+			      <0x0 0x80100000 0x0 0x00001000>;
+			reg-names = "dbi", "atu", "config", "link", "dbi2";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			clocks = <&syscon_apmu CLK_APMU_PCIE_PORTA_DBI>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTA_MSTE>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTA_SLV>;
+			clock-names = "dbi", "mstr", "slv";
+			msi-parent = <&simsic>;
+			ranges = <0x01000000 0x00 0x00010000 0x11 0x00010000 0x0 0x00100000>,
+				 <0x02000000 0x0 0x00110000 0x11 0x00110000 0x0 0x7fef0000>,
+				 <0x43000000 0x18 0x00000000 0x18 0x00000000 0x1 0x00000000>;
+			resets = <&syscon_apmu RESET_APMU_PCIE_A_DBI>,
+				 <&syscon_apmu RESET_APMU_PCIE_A_MASTER>,
+				 <&syscon_apmu RESET_APMU_PCIE_A_SLAVE>;
+			reset-names = "dbi", "mstr", "slv";
+			max-link-speed = <3>;
+			linux,pci-domain = <0>;
+			spacemit,apmu = <&syscon_apmu 0x1f0>;
+			status = "disabled";
+
+			pcie0_port: pcie@0 {
+				device_type = "pci";
+				compatible = "pciclass,0604";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
+		};
+
+		pcie1_rc: pcie@80400000 {
+			compatible = "spacemit,k3-pcie";
+			reg = <0x0 0x80400000 0x0 0x00001000>,
+			      <0x0 0x80700000 0x0 0x00003f20>,
+			      <0x11 0x80000000 0x0 0x00010000>,
+			      <0x0 0x82c00000 0x0 0x00001000>,
+			      <0x0 0x80500000 0x0 0x00001000>;
+			reg-names = "dbi", "atu", "config", "link", "dbi2";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			clocks = <&syscon_apmu CLK_APMU_PCIE_PORTB_DBI>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTB_MSTE>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTB_SLV>;
+			clock-names = "dbi", "mstr", "slv";
+			msi-parent = <&simsic>;
+			ranges = <0x01000000 0x0 0x00010000 0x11 0x80010000 0x0 0x00100000>,
+				 <0x02000000 0x0 0x80110000 0x11 0x80110000 0x0 0x7fef0000>,
+				 <0x43000000 0x16 0x00000000 0x16 0x00000000 0x1 0x00000000>;
+			resets = <&syscon_apmu RESET_APMU_PCIE_B_DBI>,
+				 <&syscon_apmu RESET_APMU_PCIE_B_MASTER>,
+				 <&syscon_apmu RESET_APMU_PCIE_B_SLAVE>;
+			reset-names = "dbi", "mstr", "slv";
+			max-link-speed = <3>;
+			linux,pci-domain = <1>;
+			spacemit,apmu = <&syscon_apmu 0x1d0>;
+			status = "disabled";
+
+			pcie1_port: pcie@0 {
+				device_type = "pci";
+				compatible = "pciclass,0604";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
+		};
+
+		pcie2_rc: pcie@80800000 {
+			compatible = "spacemit,k3-pcie";
+			reg = <0x0 0x80800000 0x0 0x00001000>,
+			      <0x0 0x80b00000 0x0 0x00003f20>,
+			      <0x12 0x00000000 0x0 0x00010000>,
+			      <0x0 0x82d00000 0x0 0x00001000>,
+			      <0x0 0x80900000 0x0 0x00001000>;
+			reg-names = "dbi", "atu", "config", "link", "dbi2";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			clocks = <&syscon_apmu CLK_APMU_PCIE_PORTC_DBI>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTC_MSTE>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTC_SLV>;
+			clock-names = "dbi", "mstr", "slv";
+			msi-parent = <&simsic>;
+			ranges = <0x01000000 0x00 0x00000000 0x12 0x00010000 0x0 0x00100000>,
+				 <0x02000000 0x0 0x00110000 0x12 0x00110000 0x0 0x7fef0000>,
+				 <0x43000000 0x15 0x00000000 0x15 0x00000000 0x1 0x00000000>;
+			resets = <&syscon_apmu RESET_APMU_PCIE_C_DBI>,
+				 <&syscon_apmu RESET_APMU_PCIE_C_MASTER>,
+				 <&syscon_apmu RESET_APMU_PCIE_C_SLAVE>;
+			reset-names = "dbi", "mstr", "slv";
+			linux,pci-domain = <2>;
+			max-link-speed = <3>;
+			spacemit,apmu = <&syscon_apmu 0x1c8>;
+			status = "disabled";
+
+			pcie2_port: pcie@0 {
+				device_type = "pci";
+				compatible = "pciclass,0604";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
+		};
+
+		pcie3_rc: pcie@80c00000 {
+			compatible = "spacemit,k3-pcie";
+			reg = <0x0 0x80c00000 0x0 0x00001000>,
+			      <0x0 0x80f00000 0x0 0x00003f20>,
+			      <0x12 0x80000000 0x0 0x00010000>,
+			      <0x0 0x82a00000 0x0 0x00001000>,
+			      <0x0 0x80d00000 0x0 0x00001000>;
+			reg-names = "dbi", "atu", "config", "link", "dbi2";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			clocks = <&syscon_apmu CLK_APMU_PCIE_PORTD_DBI>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTD_MSTE>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTD_SLV>;
+			clock-names = "dbi", "mstr", "slv";
+			msi-parent = <&simsic>;
+			ranges = <0x01000000 0x0 0x00010000 0x12 0x80010000 0x0 0x100000>,
+				 <0x02000000 0x0 0x80110000 0x12 0x80110000 0x0 0x3fef0000>,
+				 <0x43000000 0x14 0x00000000 0x14 0x00000000 0x1 0x00000000>;
+			resets = <&syscon_apmu RESET_APMU_PCIE_D_DBI>,
+				 <&syscon_apmu RESET_APMU_PCIE_D_MASTER>,
+				 <&syscon_apmu RESET_APMU_PCIE_D_SLAVE>;
+			reset-names = "dbi", "mstr", "slv";
+			linux,pci-domain = <3>;
+			bus-range = <0x00 0xff>;
+			max-link-speed = <3>;
+			spacemit,apmu = <&syscon_apmu 0x1e0>;
+			status = "disabled";
+
+			pcie3_port: pcie@0 {
+				device_type = "pci";
+				compatible = "pciclass,0604";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
+		};
+
+		pcie4_rc: pcie@81000000 {
+			compatible = "spacemit,k3-pcie";
+			reg = <0x0 0x81000000 0x0 0x00001000>,
+			      <0x0 0x81300000 0x0 0x00003f20>,
+			      <0x12 0xc0000000 0x0 0x00010000>,
+			      <0x0 0x82b00000 0x0 0x00001000>,
+			      <0x0 0x81100000 0x0 0x00001000>;
+			reg-names = "dbi", "atu", "config", "link", "dbi2";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			clocks = <&syscon_apmu CLK_APMU_PCIE_PORTE_DBI>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTE_MSTE>,
+				 <&syscon_apmu CLK_APMU_PCIE_PORTE_SLV>;
+			clock-names = "dbi", "mstr", "slv";
+			msi-parent = <&simsic>;
+			ranges = <0x01000000 0x0 0x00000000 0x12 0xc0010000 0x0 0x100000>,
+				 <0x02000000 0x0 0xc0110000 0x12 0xc0110000 0x0 0x3fef0000>,
+				 <0x43000000 0x13 0x00000000 0x13 0x00000000 0x1 0x00000000>;
+			resets = <&syscon_apmu RESET_APMU_PCIE_E_DBI>,
+				 <&syscon_apmu RESET_APMU_PCIE_E_MASTER>,
+				 <&syscon_apmu RESET_APMU_PCIE_E_SLAVE>;
+			reset-names = "dbi", "mstr", "slv";
+			linux,pci-domain = <4>;
+			max-link-speed = <3>;
+			spacemit,apmu = <&syscon_apmu 0x1e8>;
+			status = "disabled";
+
+			pcie4_port: pcie@0 {
+				device_type = "pci";
+				compatible = "pciclass,0604";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
+		};
+
 		usb3d: usb@81a00000 {
 			compatible = "spacemit,k3-dwc3";
 			reg = <0x0 0x81a00000 0x0 0x10000>;
-- 
2.55.0