[PATCH 6.12.y/6.18.y/7.1.y] drm/amd/display: Fix DTB DTO updates breaking live pixel rate sources

From: Harry Wentland <[email protected]>

commit 76a2db58e95e328007043f54ac3c7336ccbee440 upstream.

dcn32_update_clocks_update_dtb_dto() and its dcn35 counterpart reprogram
the DTB DTO of every timing generator in the context whenever the DTBCLK
reference changes, passing a zeroed pixel rate and never setting
is_hdmi. Both dccg set_dtbclk_dto() implementations treat a zero pixel
rate as a disable request. On dcn32 that branch drives PIPE_DTO_SRC_SEL
to the DP DTO source, so a timing generator actively scanning out an
HDMI stream has its pixel rate source re-muxed out from under the live
raster and the OTG stops on the spot. On dcn35 it clears
DTBCLK_DTO_ENABLE and restores DTBCLK_Pn clock gating, which does the
same to a live 128b/132b stream.

Two displays where only one runs a 128b/132b link hit this reliably.
is_dtbclk_required() holds the DTBCLK reference high while both are
active, and the moment the 128b/132b stream is torn down (compositor
switch, display disable, hot-unplug) the next safe_to_lower pass drops
the reference to the lowest DPM level and the DTO walk freezes the
surviving screen. On Navi31 the DAL mailbox then goes deaf on the
DISPCLK hard-min that follows the walk in dcn32_update_clocks(),
stranding both SMU mailboxes until reboot.

Set is_hdmi for HDMI and DVI signals so the disable path leaves the
pixel rate source selection on the HDMI path, and pass the real pixel
rate for 128b/132b streams so a reference change rescales their DTO
instead of disabling it.

Fixes: 128c1ca0303f ("drm/amd/display: Update DTBCLK for DCN32")
Fixes: 8774029f76b9 ("drm/amd/display: Add DCN35 CLK_MGR")
Signed-off-by: Harry Wentland <[email protected]>
Reviewed-by: Fangzhi Zuo <[email protected]>
Tested-by: Dan Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
[ mschwartz: dcn32 and dcn35 clk_mgr hunks only. The rest is HDMI FRL
  enablement, absent before 7.2, so the FRL conditions and the
  req_audio_dtbclk_khz assignment they guard are dropped and the
  FRL-centric changelog is rewritten. Added the pipe_ctx->stream check
  the new dereferences need. ]
Signed-off-by: Matthew Schwartz <[email protected]>
---
6.6.y needs the dcn32 hunk alone and is sent alongside this one. Tested
on Navi31 with a DisplayPort UHBR monitor and an HDMI TV.

diff --git a/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn32/dcn32_clk_mgr.c b/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn32/dcn32_clk_mgr.c
index 084994c650c4..285689d7ecc4 100644
--- a/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn32/dcn32_clk_mgr.c
+++ b/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn32/dcn32_clk_mgr.c
@@ -276,13 +276,20 @@ static void dcn32_update_clocks_update_dtb_dto(struct clk_mgr_internal *clk_mgr,
 		struct dtbclk_dto_params dto_params = {0};
 
 		/* use mask to program DTO once per tg */
-		if (pipe_ctx->stream_res.tg &&
+		if (pipe_ctx->stream && pipe_ctx->stream_res.tg &&
 				!(tg_mask & (1 << pipe_ctx->stream_res.tg->inst))) {
 			tg_mask |= (1 << pipe_ctx->stream_res.tg->inst);
 
 			dto_params.otg_inst = pipe_ctx->stream_res.tg->inst;
 			dto_params.ref_dtbclk_khz = ref_dtbclk_khz;
 
+			if (dccg->ctx->dc->link_srv->dp_is_128b_132b_signal(pipe_ctx))
+				dto_params.pixclk_khz = pipe_ctx->stream->timing.pix_clk_100hz / 10;
+
+			if (dc_is_hdmi_signal(pipe_ctx->stream->signal) ||
+					dc_is_dvi_signal(pipe_ctx->stream->signal))
+				dto_params.is_hdmi = true;
+
 			dccg->funcs->set_dtbclk_dto(clk_mgr->dccg, &dto_params);
 			//dccg->funcs->set_audio_dtbclk_dto(clk_mgr->dccg, &dto_params);
 		}
diff --git a/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn35/dcn35_clk_mgr.c b/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn35/dcn35_clk_mgr.c
index bb1ac12a2b09..d154383a3961 100644
--- a/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn35/dcn35_clk_mgr.c
+++ b/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn35/dcn35_clk_mgr.c
@@ -264,13 +264,20 @@ static void dcn35_update_clocks_update_dtb_dto(struct clk_mgr_internal *clk_mgr,
 		struct dtbclk_dto_params dto_params = {0};
 
 		/* use mask to program DTO once per tg */
-		if (pipe_ctx->stream_res.tg &&
+		if (pipe_ctx->stream && pipe_ctx->stream_res.tg &&
 				!(tg_mask & (1 << pipe_ctx->stream_res.tg->inst))) {
 			tg_mask |= (1 << pipe_ctx->stream_res.tg->inst);
 
 			dto_params.otg_inst = pipe_ctx->stream_res.tg->inst;
 			dto_params.ref_dtbclk_khz = ref_dtbclk_khz;
 
+			if (dccg->ctx->dc->link_srv->dp_is_128b_132b_signal(pipe_ctx))
+				dto_params.pixclk_khz = pipe_ctx->stream->timing.pix_clk_100hz / 10;
+
+			if (dc_is_hdmi_signal(pipe_ctx->stream->signal) ||
+					dc_is_dvi_signal(pipe_ctx->stream->signal))
+				dto_params.is_hdmi = true;
+
 			dccg->funcs->set_dtbclk_dto(clk_mgr->dccg, &dto_params);
 			//dccg->funcs->set_audio_dtbclk_dto(clk_mgr->dccg, &dto_params);
 		}
-- 
2.50.1