Re: [PATCH v1 0/7] Add HPD support for Rockchip Analogix DP
Damon Ding <[email protected]>
| Newsgroups | org.freedesktop.lists.dri-devel,org.infradead.lists.linux-arm-kernel,org.infradead.lists.linux-rockchip,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-kernel |
|---|---|
| Message-ID | <[email protected]> |
Hi Heiko,
On 7/31/2026 2:49 AM, Heiko Stübner wrote:
> Hi Damon,
>
> Am Donnerstag, 30. Juli 2026, 05:27:37 Mitteleuropäische Sommerzeit schrieb Damon Ding:
>> This series improves the HPD (Hotplug Detect) interrupt handling in
>> the Analogix DP driver to enable reliable native HPD pin detection on
>> Rockchip platforms, and introduces platform-specific HPD detection
>> schemes with fine-grained interrupt control.
>
> [...]
>
>> Tested on RK3576 with both native HPD pin and GPIO HPD configurations.
>>
>> Native HPD pin mode:
>>
>> &edp {
>> status = "okay";
>> pinctrl-names = "default";
>> pinctrl-0 = <&edp_txm0_pins>;
>> };
>>
>> GPIO HPD mode:
>>
>> &edp {
>> status = "okay";
>> pinctrl-names = "default";
>> pinctrl-0 = <&edp0_hpd>;
>> hpd-gpios = <&gpio4 RK_PC1 GPIO_ACTIVE_HIGH>;
>> };
>>
>> &pinctrl {
>> edp {
>> edp0_hpd: edp0-hpd {
>> rockchip,pins = <4 RK_PC1 0 &pcfg_pull_none>;
>> };
>> };
>> };
>
> Yay and thanks a lot for working on that.
>
> If I roll my display-port carrier board back to the analogix-dp being
> the endpoint, this works exactly as expected :-) .
>
> I can plug in the display at some point after the boot and have it
> detected and setup correctly. Same with unplugging it while
> the system is running. The connection status is correctly reported
> in sysfs.
>
>
> Though there is a caveat. When the eDP is not the last part, this does not
> work anymore. The detect function always returns "connected" if there is
> a next bridge available.
>
> My board [0] has a physical DP connector on it, so models it as
> dp-connector, but in that case the Analogix driver always reports being
> connected.
>
>
> [0] https://lore.kernel.org/linux-rockchip/[email protected]/
> ... same effect with hpd-gpios in either the edp node or dp-connector node
>
>
My previous tests were carried out on the modified RK3576 IOTEST board
DTS based on RK3576 EVB1, which includes dp-connector by default. I also
did extra verification without dp-connector, and HPD detection works
correctly in both cases.
I've taken a look at the Tiger board DT configuration. The pinctrl
settings for the eDP HPD GPIO may need adjustment:
&pinctrl {
edp0 {
edp0_hpd_l: edp0-hpd-l-pin {
rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
};
It is recommended to configure GPIO4B5 as pull-down or pll-none. Pull-up
configuration may prevent GPIO interrupts from being triggered properly,
resulting in a permanent "connected" status.
Could you help try this modification and see if it resolves the issue?
Best regards,
Damon
0001-TEST-arm64-dts-rockchip-Enable-eDP2DP-display-on-RK3.patch
(text/plain, 25.8 KB)
From 1fb4d0c29681407367c8d93770c30c2213174473 Mon Sep 17 00:00:00 2001 From: Damon Ding <[email protected]> Date: Tue, 28 Jul 2026 10:00:18 +0800 Subject: [PATCH] [TEST]arm64: dts: rockchip: Enable eDP2DP display on RK3576 IOTEST board Signed-off-by: Damon Ding <[email protected]> --- .../boot/dts/rockchip/rk3576-iotest-v10.dts | 1126 +++++++++++++++++ 1 file changed, 1126 insertions(+) create mode 100755 arch/arm64/boot/dts/rockchip/rk3576-iotest-v10.dts diff --git a/arch/arm64/boot/dts/rockchip/rk3576-iotest-v10.dts b/arch/arm64/boot/dts/rockchip/rk3576-iotest-v10.dts new file mode 100755 index 000000000000..197087c831f6 --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3576-iotest-v10.dts @@ -0,0 +1,1126 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2024 Rockchip Electronics Co., Ltd. + * + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/soc/rockchip,vop2.h> +#include "rk3576.dtsi" + +/ { + model = "Rockchip RK3576 EVB V10 Board"; + compatible = "rockchip,rk3576-evb1-v10", "rockchip,rk3576"; + + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + power-supply = <&vcc3v3_lcd_n>; + pwms = <&gpio_pwm0 0 25000 0>; + }; + + chosen: chosen { + stdout-path = "serial0:1500000n8"; + bootargs = "root=PARTUUID=614e0000-0000 rootwait"; + }; + + adc_keys: adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 1>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1800000>; + poll-interval = <100>; + + button-back { + label = "back"; + linux,code = <KEY_BACK>; + press-threshold-microvolt = <1235000>; + }; + + button-menu { + label = "menu"; + linux,code = <KEY_MENU>; + press-threshold-microvolt = <890000>; + }; + + button-vol-down { + label = "volume down"; + linux,code = <KEY_VOLUMEDOWN>; + press-threshold-microvolt = <417000>; + }; + + button-vol-up { + label = "volume up"; + linux,code = <KEY_VOLUMEUP>; + press-threshold-microvolt = <17000>; + }; + }; + + dp-con { + compatible = "dp-connector"; + label = "DP OUT"; + type = "full-size"; + + port { + dp_con_in: endpoint { + remote-endpoint = <&edp_out_conn>; + }; + }; + }; + + hdmi-con { + compatible = "hdmi-connector"; + type = "a"; + }; + + leds: leds { + compatible = "gpio-leds"; + + work_led: led-0 { + gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_pwm0: gpio-pwm0 { + compatible = "pwm-gpio"; + gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&gpio_pwm0_pin>; + pinctrl-names = "default"; + #pwm-cells = <3>; + }; + + vbus5v0_typec: regulator-vbus5v0-typec { + compatible = "regulator-fixed"; + regulator-name = "vbus5v0_typec"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&gpio0 RK_PD1 GPIO_ACTIVE_HIGH>; + vin-supply = <&vcc5v0_device>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_otg0_pwren>; + }; + + vcc12v_dcin: regulator-vcc12v-dcin { + compatible = "regulator-fixed"; + regulator-name = "vcc12v_dcin"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; + + vcc1v2_ufs_vccq_s0: regulator-vcc1v2-ufs-vccq-s0 { + compatible = "regulator-fixed"; + regulator-name = "vcc1v2_ufs_vccq_s0"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <&vcc_sys>; + }; + + vcc1v8_ufs_vccq2_s0: regulator-vcc1v8-ufs-vccq2-s0 { + compatible = "regulator-fixed"; + regulator-name = "vcc1v8_ufs_vccq2_s0"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_1v8_s3>; + }; + + vcc3v3_lcd_n: regulator-vcc3v3-lcd0-n { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_lcd0_n"; + regulator-boot-on; + enable-active-high; + gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; + vin-supply = <&vcc_3v3_s0>; + }; + + vcc3v3_pcie1: regulator-vcc3v3-pcie1 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_pcie1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_HIGH>; + startup-delay-us = <5000>; + vin-supply = <&vcc12v_dcin>; + }; + + vcc3v3_rtc_s5: regulator-vcc3v3-rtc-s5 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_rtc_s5"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_sys>; + }; + + vcc5v0_device: regulator-vcc5v0-device { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_device"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc12v_dcin>; + }; + + vcc5v0_host: regulator-vcc5v0-host { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_host"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>; + vin-supply = <&vcc5v0_device>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_host_pwren>; + }; + + vcc_sys: regulator-vcc5v0-sys { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc12v_dcin>; + }; + + vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 { + compatible = "regulator-fixed"; + regulator-name = "vcc_1v1_nldo_s3"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + vin-supply = <&vcc_sys>; + }; + + vcc_1v8_s0: regulator-vcc-1v8-s0 { + compatible = "regulator-fixed"; + regulator-name = "vcc_1v8_s0"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_1v8_s3>; + }; + + vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 { + compatible = "regulator-fixed"; + regulator-name = "vcc_2v0_pldo_s3"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + vin-supply = <&vcc_sys>; + }; + + vcc_3v3_s0: regulator-vcc-3v3-s0 { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_s0"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_3v3_s3>; + }; + + vcc3v3_sd: regulator-vcc-3v3-sd { + compatible = "regulator-fixed"; + enable-active-high; + gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_pwren>; + regulator-name = "vcc3v3_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_3v3_s0>; + }; + + vcc_ufs_s0: regulator-vcc-ufs-s0 { + compatible = "regulator-fixed"; + regulator-name = "vcc_ufs_s0"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_sys>; + }; + + vcc_wifi_reg_on: regulator-wifi-reg-on { + compatible = "regulator-fixed"; + enable-active-high; + gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&wifi_reg_on>; + pinctrl-names = "default"; + regulator-name = "wifi_reg_on"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_1v8_s3>; + }; + + sound { + compatible = "simple-audio-card"; + pinctrl-names = "default"; + pinctrl-0 = <&hp_det>; + simple-audio-card,name = "On-board Analog ES8388"; + simple-audio-card,aux-devs = <&hp_power>, <&spk_power>; + simple-audio-card,bitclock-master = <&masterdai>; + simple-audio-card,format = "i2s"; + simple-audio-card,frame-master = <&masterdai>; + simple-audio-card,hp-det-gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>; + simple-audio-card,mclk-fs = <256>; + simple-audio-card,pin-switches = "Headphones", "Speaker", "Main Mic", "Headset Mic"; + simple-audio-card,routing = + "Headphone Power INL", "LOUT1", + "Headphone Power INR", "ROUT1", + "Speaker Power INL", "LOUT2", + "Speaker Power INR", "ROUT2", + "Headphones", "Headphone Power OUTL", + "Headphones", "Headphone Power OUTR", + "Speaker", "Speaker Power OUTL", + "Speaker", "Speaker Power OUTR", + "LINPUT1", "Main Mic", + "LINPUT2", "Main Mic", + "RINPUT1", "Headset Mic", + "RINPUT2", "Headset Mic"; + simple-audio-card,widgets = + "Microphone", "Main Mic", + "Microphone", "Headset Mic", + "Headphone", "Headphones", + "Speaker", "Speaker"; + + simple-audio-card,cpu { + sound-dai = <&sai1>; + }; + + masterdai: simple-audio-card,codec { + sound-dai = <&es8388>; + system-clock-frequency = <12288000>; + }; + }; + + hp_power: headphone-amplifier { + compatible = "simple-audio-amplifier"; + enable-gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&hp_ctl>; + sound-name-prefix = "Headphone Power"; + }; + + spk_power: speaker-amplifier { + compatible = "simple-audio-amplifier"; + enable-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spk_ctl>; + sound-name-prefix = "Speaker Power"; + VCC-supply = <&vcc5v0_device>; + }; +}; + +&cpu_l0 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_b0 { + cpu-supply = <&vdd_cpu_big_s0>; +}; + +&combphy0_ps { + status = "okay"; +}; + +&combphy1_psu { + status = "okay"; +}; + +&edp { + status = "okay"; + pinctrl-names = "default"; + /* + * Please check the switch of GPIO4_C1, it may not be switched to + * eDP HPD function by default. + */ + pinctrl-0 = <&edp_txm0_pins>; + // pinctrl-0 = <&edp0_hpd>; + // hpd-gpios = <&gpio4 RK_PC1 GPIO_ACTIVE_HIGH>; +}; + +// &pinctrl { +// edp { +// edp0_hpd: edp0-hpd { +// rockchip,pins = <4 RK_PC1 0 &pcfg_pull_none>; +// }; +// }; +// }; + +&edp_in { + edp_in_vp0: endpoint { + remote-endpoint = <&vp0_out_edp>; + }; +}; + +&edp_out { + edp_out_conn: endpoint { + remote-endpoint = <&dp_con_in>; + }; +}; + +&gmac0 { + clock_in_out = "output"; + phy-mode = "rgmii-rxid"; + phy-handle = <&rgmii_phy0>; + pinctrl-names = "default"; + pinctrl-0 = <ð0m0_miim + ð0m0_tx_bus2 + ð0m0_rx_bus2 + ð0m0_rgmii_clk + ð0m0_rgmii_bus + ðm0_clk0_25m_out>; + tx_delay = <0x21>; + status = "okay"; +}; + +&gmac1 { + clock_in_out = "output"; + phy-handle = <&rgmii_phy1>; + phy-mode = "rgmii-rxid"; + pinctrl-names = "default"; + pinctrl-0 = <ð1m0_miim + ð1m0_tx_bus2 + ð1m0_rx_bus2 + ð1m0_rgmii_clk + ð1m0_rgmii_bus + ðm0_clk1_25m_out>; + tx_delay = <0x20>; + status = "okay"; +}; + +&gpu { + mali-supply = <&vdd_gpu_s0>; + status = "okay"; +}; + +&hdmi { + status = "disabled"; +}; + +&hdmi_sound { + status = "disabled"; +}; + +&hdptxphy { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + rk806: pmic@23 { + compatible = "rockchip,rk806"; + reg = <0x23>; + interrupt-parent = <&gpio0>; + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; + gpio-controller; + #gpio-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>, + <&rk806_dvs2_null>, <&rk806_dvs3_null>; + system-power-controller; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc5-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; + vcc8-supply = <&vcc_sys>; + vcc9-supply = <&vcc_sys>; + vcc10-supply = <&vcc_sys>; + vcc11-supply = <&vcc_2v0_pldo_s3>; + vcc12-supply = <&vcc_sys>; + vcc13-supply = <&vcc_1v1_nldo_s3>; + vcc14-supply = <&vcc_1v1_nldo_s3>; + vcca-supply = <&vcc_sys>; + + rk806_dvs1_null: dvs1-null-pins { + pins = "gpio_pwrctrl1"; + function = "pin_fun0"; + }; + + rk806_dvs2_null: dvs2-null-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun0"; + }; + + rk806_dvs3_null: dvs3-null-pins { + pins = "gpio_pwrctrl3"; + function = "pin_fun0"; + }; + + rk806_dvs1_slp: dvs1-slp-pins { + pins = "gpio_pwrctrl1"; + function = "pin_fun1"; + }; + + rk806_dvs1_pwrdn: dvs1-pwrdn-pins { + pins = "gpio_pwrctrl1"; + function = "pin_fun2"; + }; + + rk806_dvs1_rst: dvs1-rst-pins { + pins = "gpio_pwrctrl1"; + function = "pin_fun3"; + }; + + rk806_dvs2_slp: dvs2-slp-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun1"; + }; + + rk806_dvs2_pwrdn: dvs2-pwrdn-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun2"; + }; + + rk806_dvs2_rst: dvs2-rst-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun3"; + }; + + rk806_dvs2_dvs: dvs2-dvs-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun4"; + }; + + rk806_dvs2_gpio: dvs2-gpio-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun5"; + }; + + rk806_dvs3_slp: dvs3-slp-pins { + pins = "gpio_pwrctrl3"; + function = "pin_fun1"; + }; + + rk806_dvs3_pwrdn: dvs3-pwrdn-pins { + pins = "gpio_pwrctrl3"; + function = "pin_fun2"; + }; + + rk806_dvs3_rst: dvs3-rst-pins { + pins = "gpio_pwrctrl3"; + function = "pin_fun3"; + }; + + rk806_dvs3_dvs: dvs3-dvs-pins { + pins = "gpio_pwrctrl3"; + function = "pin_fun4"; + }; + + rk806_dvs3_gpio: dvs3-gpio-pins { + pins = "gpio_pwrctrl3"; + function = "pin_fun5"; + }; + + regulators { + vdd_cpu_big_s0: dcdc-reg1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <950000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_cpu_big_s0"; + regulator-enable-ramp-delay = <400>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_npu_s0: dcdc-reg2 { + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <950000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_npu_s0"; + regulator-enable-ramp-delay = <400>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_cpu_lit_s0: dcdc-reg3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <950000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_cpu_lit_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <750000>; + }; + }; + + vcc_3v3_s3: dcdc-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_3v3_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vdd_gpu_s0: dcdc-reg5 { + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <900000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_gpu_s0"; + regulator-enable-ramp-delay = <400>; + + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <850000>; + }; + }; + + vddq_ddr_s0: dcdc-reg6 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vddq_ddr_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_logic_s0: dcdc-reg7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <800000>; + regulator-name = "vdd_logic_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8_s3: dcdc-reg8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_1v8_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdd2_ddr_s3: dcdc-reg9 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vdd2_ddr_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vdd_ddr_s0: dcdc-reg10 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vdd_ddr_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca_1v8_s0: pldo-reg1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca_1v8_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca1v8_pldo2_s0: pldo-reg2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca1v8_pldo2_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda_1v2_s0: pldo-reg3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vdda_1v2_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca_3v3_s0: pldo-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_3v3_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd_s0: pldo-reg5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca1v8_pldo6_s3: pldo-reg6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca1v8_pldo6_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdd_0v75_s3: nldo-reg1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <750000>; + regulator-name = "vdd_0v75_s3"; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <750000>; + }; + }; + + vdda_ddr_pll_s0: nldo-reg2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-name = "vdda_ddr_pll_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v75_hdmi_s0: nldo-reg3 { + regulator-boot-on; + regulator-min-microvolt = <837500>; + regulator-max-microvolt = <837500>; + regulator-name = "vdda0v75_hdmi_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda_0v85_s0: nldo-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-name = "vdda_0v85_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda_0v75_s0: nldo-reg5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <750000>; + regulator-name = "vdda_0v75_s0"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&i2c2 { + status = "okay"; + + hym8563: rtc@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + clock-output-names = "hym8563"; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA0 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&rtc_int>; + wakeup-source; + #clock-cells = <0>; + }; +}; + +&i2c3 { + status = "okay"; + + es8388: audio-codec@10 { + compatible = "everest,es8388", "everest,es8328"; + reg = <0x10>; + AVDD-supply = <&vcca_3v3_s0>; + DVDD-supply = <&vcc_1v8_s0>; + HPVDD-supply = <&vcca_3v3_s0>; + PVDD-supply = <&vcc_1v8_s0>; + assigned-clocks = <&cru CLK_SAI1_MCLKOUT_TO_IO>; + assigned-clock-rates = <12288000>; + clocks = <&cru CLK_SAI1_MCLKOUT_TO_IO>; + pinctrl-names = "default"; + pinctrl-0 = <&sai1m0_mclk>; + #sound-dai-cells = <0>; + }; +}; + +&mdio0 { + rgmii_phy0: ethernet-phy@1 { + compatible = "ethernet-phy-id001c.c916"; + reg = <0x1>; + clocks = <&cru REFCLKO25M_GMAC0_OUT>; + assigned-clocks = <&cru REFCLKO25M_GMAC0_OUT>; + assigned-clock-rates = <25000000>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_phy0_rst>; + reset-assert-us = <20000>; + reset-deassert-us = <100000>; + reset-gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>; + }; +}; + +&mdio1 { + rgmii_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-id001c.c916"; + reg = <0x1>; + clocks = <&cru REFCLKO25M_GMAC1_OUT>; + assigned-clocks = <&cru REFCLKO25M_GMAC1_OUT>; + assigned-clock-rates = <25000000>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_phy1_rst>; + reset-assert-us = <20000>; + reset-deassert-us = <100000>; + reset-gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>; + }; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_rst>; + reset-gpios = <&gpio2 RK_PB4 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc_3v3_s3>; + status = "okay"; + + pcie@0,0 { + reg = <0x0 0 0 0 0>; + bus-range = <0x0 0xf>; + device_type = "pci"; + ranges; + #address-cells = <3>; + #size-cells = <2>; + + wifi: wifi@0,0 { + compatible = "pci14e4,449d"; + reg = <0x10000 0 0 0 0>; + clocks = <&hym8563>; + clock-names = "lpo"; + }; + }; +}; + +&pcie1 { + reset-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_pcie1>; + + /* + * Disable usb_drd1_dwc3 if enabling pcie1 and set Dial_Switch_1 + * to low state according to the schematic of page 17. + */ + status = "disabled"; +}; + +&pinctrl { + gpio_pwm0 { + gpio_pwm0_pin: gpio-pwm0-pin { + rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + + audio { + hp_det: hp-det { + rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + hp_ctl: hp-ctl { + rockchip,pins = <3 RK_PD6 RK_FUNC_GPIO &pcfg_pull_down>; + }; + + spk_ctl: spk-ctl { + rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + bluetooth { + bt_reg_on: bt-reg-on { + rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + bt_wake_host: bt-wake-host { + rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>; + }; + + host_wake_bt: host-wake-bt { + rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + hdmi { + hdmi_tx_on_h: hdmi-tx-on-h { + rockchip,pins = <2 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + hym8563 { + rtc_int: rtc-int { + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + network { + rgmii_phy0_rst: rgmii-phy0-rst { + rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + rgmii_phy1_rst: rgmii-phy1-rst { + rockchip,pins = <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pcie0 { + pcie0_rst: pcie0-rst { + rockchip,pins = <2 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sdmmc { + sdmmc_pwren: sdmmc-pwren { + rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb { + usb_host_pwren: usb-host-pwren { + rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + usb_otg0_pwren: usb-otg0-pwren { + rockchip,pins = <0 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + usbc0_int: usbc0-int { + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + wifi { + wifi_reg_on: wifi-reg-on { + rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + wifi_wake_host: wifi-wake-host { + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; +}; + +&sai1 { + pinctrl-names = "default"; + pinctrl-0 = <&sai1m0_lrck + &sai1m0_sclk + &sai1m0_sdi0 + &sai1m0_sdo0>; + status = "okay"; +}; + +&sai6 { + status = "okay"; +}; + +&sdhci { + bus-width = <8>; + full-pwr-cycle-in-suspend; + max-frequency = <200000000>; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + no-sdio; + no-sd; + non-removable; + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>; + disable-wp; + max-frequency = <200000000>; + no-sdio; + no-mmc; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_det &sdmmc0_bus4>; + sd-uhs-sdr104; + vmmc-supply = <&vcc3v3_sd>; + vqmmc-supply = <&vccio_sd_s0>; + status = "okay"; +}; + +&saradc { + vref-supply = <&vcca_1v8_s0>; + status = "okay"; +}; + +&u2phy0 { + status = "okay"; +}; + +&u2phy0_otg { + phy-supply = <&vbus5v0_typec>; + status = "okay"; +}; + +&u2phy1 { + status = "okay"; +}; + +&u2phy1_otg { + phy-supply = <&vcc5v0_host>; + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart4 { + pinctrl-0 = <&uart4m1_xfer &uart4m1_ctsn &uart4m1_rtsn>; + pinctrl-names = "default"; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + clocks = <&hym8563>; + clock-names = "lpo"; + device-wakeup-gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PB1 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-0 = <&bt_reg_on &bt_wake_host &host_wake_bt>; + pinctrl-names = "default"; + shutdown-gpios = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>; + vbat-supply = <&vcc_3v3_s3>; + vddio-supply = <&vcc_1v8_s3>; + }; +}; + +&ufshc { + status = "okay"; +}; + +&usbdp_phy { + rockchip,dp-lane-mux = <2 3>; + status = "okay"; +}; + +&usb_drd0_dwc3 { + dr_mode = "host"; + status = "okay"; +}; + +&usb_drd1_dwc3 { + dr_mode = "host"; + status = "okay"; +}; + +&vop { + status = "okay"; +}; + +&vop_mmu { + status = "okay"; +}; + +&vp0 { + vp0_out_edp: endpoint@ROCKCHIP_VOP2_EP_EDP0 { + reg = <ROCKCHIP_VOP2_EP_EDP0>; + remote-endpoint = <&edp_in_vp0>; + }; +}; -- 2.34.1