Re: ath12k: WCN785x firmware resets regulatory domain on resume causing ~7s reconnect delay

On 7/17/2026 6:35 AM, Stian Knudsen wrote:
> After resume from suspend, the WCN785x firmware resets its regulatory state to
> WORLD and takes approximately 7 seconds to re-discover the country code from AP
> beacons. This causes a consistent ~16 second total delay before wifi reconnects
> after resume.
> 
> This is an improvement request rather than a crash bug: the driver currently
> contains no WMI code for saving or restoring regulatory state across
> suspend/resume, and I would like to ask whether this is feasible.
> 
> Hardware:
> Lenovo ThinkPad T14 Gen 5 (BIOS: R2LET40W 1.21)
> Wifi: Qualcomm WCN785x Wi-Fi 7 FastConnect 7800 [17cb:1107]
> Subsystem: Lenovo [17aa:e0e6]
> Kernel: 7.1.3-arch2-1 (Arch Linux, close to vanilla)
> Firmware: WLAN.HMT.1.1.c7-00108-QCAHMTSWPL_V1.0_V2.0_SILICONZ_UPSTREAM-3
> Kernel taint: 0 (untainted)
> 
> Observed behavior:
> On every resume from suspend, the following sequence is observed in dmesg and wpa_supplicant logs:
> kernel: ath12k_wifi7_pci 0000:02:00.0: chip_id 0x2 chip_family 0x4 board_id 0xff soc_id 0x40170200
> kernel: ath12k_wifi7_pci 0000:02:00.0: fw_version 0x1103006c fw_build_timestamp 2026-03-06 09:10 ...
> wpa_supplicant: wlp2s0: CTRL-EVENT-REGDOM-CHANGE init=DRIVER type=WORLD
> [ ~7 seconds pass ]
> wpa_supplicant: wlp2s0: CTRL-EVENT-REGDOM-CHANGE init=DRIVER type=COUNTRY alpha2=DE
> [ ~9 seconds pass ]
> NetworkManager: policy: auto-activating connection 'SSID'
> NetworkManager: device (wlp2s0): Activation: successful, device activated.
> 
> Total delay from resume to connected: ~16 seconds, 100% reproducible on every
> resume.
> 
> The device advertises itself as self-managed (phy#0 (self-managed) in iw reg
> get). All standard userspace methods of setting the regulatory domain are
> ignored by the firmware -- iw reg set, wireless-regdb, cfg80211
> ieee80211_regdom modprobe option -- and i found this blog which documents this:
> https://www.julienturbide.com/blog/wifi-7-linux-ath12k-wcn785x-regulatory-domain
> 
> Grepping the ath12k driver source (7.1.3) reveals no WMI code for saving or
> restoring regulatory state across suspend/resume:
>  $ grep -r "regdom|regulatory|country.*suspend|suspend.*country" drivers/net/wireless/ath/ath12k/
> (no output)
> 
> The firmware resets to WORLD on every resume and must re-discover the country
> code from AP beacons, taking ~7 seconds.
> 
> Is there a WMI command available in the WCN785x firmware to cache and restore
> the last known country code on resume, avoiding the need to re-discover it from AP beacons? If so, would it be feasible to add this to the driver's suspend/resume path to reduce the post-resume reconnect delay?
> Full dmesg output and wpa_supplicant logs are available on request.

ath11k has the same issue and there is a commit fixing it

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7f0343b7b8710436c1e6355c71782d32ada47e0c

in ath12k, the same command/function (ath12k_wmi_send_set_current_country_cmd()) can do
this for you.

> 
> 
>