Fwd: lspci not working

On 17-05-15 16:08, Schmirr Wurst wrote:
> ---------- Forwarded message ----------
> From: Schmirr Wurst <[email protected]>
> Date: 2015-05-17 16:07 GMT+02:00
> Subject: Re: lspci not working
> To: Hauke Mehrtens <[email protected]>
>
>
> 2015-05-17 15:17 GMT+02:00 Hauke Mehrtens <[email protected]>:
>> On 05/17/2015 03:00 PM, Schmirr Wurst wrote:
>>> 2015-05-17 14:57 GMT+02:00 Schmirr Wurst <[email protected]>:
>>>> I'm not familiar with inline answers and mailing list, tried to put
>>>> some order in my answer + log file
>>>>
>>>> 2015-05-17 13:18 GMT+02:00 Rafa? Mi?ecki <[email protected]>:
>>>>> On 17 May 2015 at 12:23, Arend van Spriel <[email protected]> wrote:
>>>>>> On 05/17/15 02:21, Schmirr Wurst wrote:
>>>>>>> I tried as suggested to had a look at
>>>>>>> /sys/bus/sdio/devices, but the only devices around there a 3
>>>>>>> mmc1:0001:1 to :3, I guess it is something else...
>>>>>>>
>>>>>>> I already try to install brcmfmac_sdio , with some tutorial from the
>>>>>>> internet, but it didn't work...
>>>>>>> actually, I see under /sys/bus/sdio/drivers brcmfmac_sdio ...
>>>>>>>
>>>>>>> In that directory, I see a directory mmc1:0001:2
>>>>>>> under device I have 0xa94d
>>>>>>>
>>>>>>> I completly lost, maybe you understand that information, sorry..
>>>>>>
>>>>>>
>>>>>> I do. The fact that you see a subdirectory mmc1:0001:2 in
>>>>>> /sys/bus/sdio/drivers/brcmfmac_sdio means that the driver was probed for
>>>>>> this device. Now would be a good time to share your (friends') kernel log,
>>>>>> but my guess is you are either missing firmware or nvram data or both for
>>>>>> this device.
>>>> I ve attatched the kernel.log here https://drive.google.com/file/d/0B8gm4mLCCQAgMmNlVVFSYmNjOGs/view?usp=sharing
>>>> In dmsg I see following linked with the brc driver :
>>>> dmesg | grep brc
>>>> [    7.987661] brcmf_sdio_drivestrengthinit: No SDIO Drive strength
>>>> init done for chip 43340 rev 2 pmurev 20
>>>> [    7.993487] usbcore: registered new interface driver brcmfmac
>>>> [    7.996318] brcmfmac_sdio mmc1:0001:1: Direct firmware load for
>>>> brcm/brcmfmac43340-sdio.bin failed with error -2
>>>> [    9.011572] brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
>>>> [   10.037365] brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
>>>>>
>>>>> It could also mean driver was loaded manually. So please also make
>>>>> sure the friend uses kernel 4.0 or newer.
>>>> Kernel : 4.0.0 #3 SMP PREEMPT Wed Apr 22 17:52:53 MSK 2015
>>>> Distro:
>>>> Distributor ID:    T100 Ubuntu 15.04
>>>> Description:    Ubuntu 15.04
>>>> Release:    15.04
>>>> Codename:    vivid
>>>> I ve installed it from the magic stick here
>>>> https://plus.google.com/communities/117853703024346186936
>>
>> The driver complains about missing firmware and Ubuntu 15.04 does not
>> contain it.
>>
>> Please place this file
>> https://git.kernel.org/cgit/linux/kernel/git/firmware/linux-firmware.git/plain/brcm/brcmfmac43340-sdio.bin
>>
>> to /lib/firmware/brcm/brcmfmac43340-sdio.bin
>>
>> Hauke
>   Before that, the system was complaining about
> brcm/brcmfmac43340-sdio.bin, and now about brcm/brcmfmac43340-sdio.txt
> but errors are similar...

I guess your system in jinxed because of the hostname you setup :-p

Ok, more seriously now. This is the nvram data I mentioned earlier. This 
system may have that info stored in efi variable. You should be able to 
find it in /sys/firmware/efi/efivars/nvram-*.

It may be necessary to run the following commands:

# modprobe efivarfs
# mount -t efivarfs efivarfs /sys/firmware/efi/efivars

Regards,
Arend

> 43340 rev 2 pmurev 20
> May 17 15:53:48 scheissasus kernel: [    7.372974] usbcore: registered
> new interface driver brcmfmac
> May 17 15:53:48 scheissasus kernel: [    7.374344] brcmfmac_sdio
> mmc1:0001:1: Direct firmware load for brcm/brcmfmac43340-sdio.bin
> failed with error -2
> May 17 15:53:48 scheissasus kernel: [    8.383270] brcmf_sdio_htclk:
> HT Avail timeout (1000000): clkctl 0x50
> May 17 15:53:50 scheissasus kernel: [   11.401582] brcmf_sdio_htclk:
> HT Avail timeout (1000000): clkctl 0x50
> May 17 15:59:23 scheissasus kernel: [    7.496560]
> brcmf_sdio_drivestrengthinit: No SDIO Drive strength init done for
> chip 43340 rev 2 pmurev 20
> May 17 15:59:23 scheissasus kernel: [    7.500086] usbcore: registered
> new interface driver brcmfmac
> May 17 15:59:23 scheissasus kernel: [    7.506911] brcmfmac_sdio
> mmc1:0001:1: Direct firmware load for brcm/brcmfmac43340-sdio.txt
> failed with error -2
> May 17 15:59:23 scheissasus kernel: [    8.514107] brcmf_sdio_htclk:
> HT Avail timeout (1000000): clkctl 0x50
> May 17 15:59:23 scheissasus kernel: [    9.531340] brcmf_sdio_htclk:
> HT Avail timeout (1000000): clkctl 0x50
>