Re: [PATCH v2 3/3] arm64: dts: amlogic: add support for Orbbec Zora P1

On 7/26/26 22:16, Alberto Robazza wrote:
> The Orbbec Zora P1 is an A311D (Meson G12B) board with 2/4 GiB DDR4,
> an Ampak AP6256 combo module (Broadcom BCM43456 Wi-Fi over SDIO and
> BCM4345C5 Bluetooth over UART_A), HDMI audio output.
> 
> According to the original Linux dts, the board is a modded version
> of the ODROID-N2, with Amlogic A311D instead of the original S922X
> and WiFi and Bluetooth support.
> So the device tree builds on meson-g12b-a311d.dtsi and
> meson-g12b-odroid-n2.dtsi (using same vddcpu values of N2+),
> extended with the board-specific GPIO wiring for the AP6256 handling,
> and some modifications for the led, GPIO_ACTIVE_LOW instead of
> GPIO_ACTIVE_HIGH and different label (it is a green led, not blue as
> in the Odroid N2).
> 
> Add the "orbbec,zora-p1" compatible to the amlogic.yaml board binding
> (the "orbbec" vendor prefix is already registered) and the new DTB to
> the Makefile.
> 
> Signed-off-by: Alberto Robazza <[email protected]>
> ---
>   arch/arm64/boot/dts/amlogic/Makefile          |   1 +
>   .../boot/dts/amlogic/meson-g12b-zora-p1.dts   | 103 ++++++++++++++++++
>   2 files changed, 104 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 57bc440fa..83fb38b94 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -40,6 +40,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-bananapi-m2s.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-zora-p1.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts
> new file mode 100644
> index 000000000..fe20d39a8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts
> @@ -0,0 +1,103 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2026 Alberto Robazza <[email protected]>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-g12b-a311d.dtsi"
> +#include "meson-g12b-odroid-n2.dtsi"
> +
> +/ {
> +	compatible = "orbbec,zora-p1", "amlogic,a311d", "amlogic,g12b";
> +	model = "Orbbec Zora P1";
> +
> +	leds {
> +		//The status led on Zora is actually green, same pin as N2, but reversed polarity

Use proper comment with /* and */

> +		led-blue {
> +			label = "p1:green";
> +			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>;
> +		};

Please use the new bindings with function and color properties instead if label.

> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_16 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ef 0 30518 0>;
> +	};
> +
> +	sound {
> +		model = "ZORA-P1";
> +	};
> +};
> +
> +&pwm_ef {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_e_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* AP6256 Wi-Fi: Broadcom BCM43456 over SDIO. */
> +&sd_emmc_a {
> +	status = "okay";
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <100000000>;
> +	non-removable;
> +	disable-wp;
> +	keep-power-in-suspend;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +	vmmc-supply = <&tflash_vdd>;
> +	vqmmc-supply = <&vddao_1v8>;
> +
> +	wifi@1 {
> +		compatible = "brcm,bcm4329-fmac";
> +		reg = <1>;
> +	};
> +};
> +
> +/* AP6256 Bluetooth: Broadcom BCM4345C5 over UART_A. */
> +&uart_A {
> +	status = "okay";
> +	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +
> +	bluetooth {
> +		compatible = "brcm,bcm4345c5";
> +		shutdown-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_HIGH>;
> +		max-speed = <2000000>;
> +		clocks = <&wifi32k>;
> +		clock-names = "lpo";
> +	};
> +};
> +
> +//vddcpu regulators same as Odroid N2+

Use proper comment with /* and */

> +&vddcpu_a {
> +	regulator-min-microvolt = <680000>;
> +	regulator-max-microvolt = <1040000>;
> +
> +	pwms = <&pwm_ab 0 1500 0>;
> +};
> +
> +&vddcpu_b {
> +	regulator-min-microvolt = <680000>;
> +	regulator-max-microvolt = <1040000>;
> +
> +	pwms = <&pwm_AO_cd 1 1500 0>;
> +};

Thanks,
Neil

_______________________________________________
linux-amlogic mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-amlogic