Re: [PATCH 2/2] thermal: amlogic: Add support for A9 thermal controller

Hi Daniel,
    Thanks for your review.

On 2026/8/7 20:27, Daniel Lezcano wrote:
> On 7/30/26 10:34, Xianwei Zhao via B4 Relay wrote:
>> From: Xianwei Zhao <[email protected]>
>>
>> Add support for the Amlogic A9 thermal controller.
>>
>> The A9 thermal controller uses different calibration parameters, requires
>> separate core and bus clocks, and supports a hardware over-temperature
>> reset mechanism.
>>
>> Add the A9 calibration data, retrieve the clocks by name, and configure
>> the hardware reset temperature through the optional 
>> 'amlogic,hw-reset-temp'
>> DT property. When the property is absent, use the default reset 
>> temperature
>> of 110°C.
>>
>> Also restore the hardware reset configuration after resume.
>>
>> Signed-off-by: Xianwei Zhao <[email protected]>
>> ---
>>   drivers/thermal/amlogic_thermal.c | 107 
>> ++++++++++++++++++++++++++++++++++++--
>>   1 file changed, 104 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/thermal/amlogic_thermal.c 
>> b/drivers/thermal/amlogic_thermal.c
>> index a0b530624b60..c9c351496653 100644
>> --- a/drivers/thermal/amlogic_thermal.c
>> +++ b/drivers/thermal/amlogic_thermal.c
>> @@ -45,6 +45,18 @@
>>                TSENSOR_CFG_REG1_DEM_EN |      \
>>                TSENSOR_CFG_REG1_CH_SEL)
>>
>> +#define TSENSOR_CFG_REG2                     0x8
>> +     #define TSENSOR_CFG_REG2_HITEMP_EN      BIT(31)
>> +     #define TSENSOR_CFG_REG2_REBOOT_EN      BIT(30)
>> +     #define TSENSOR_CFG_REG2_REBOOT_CODE    GENMASK(15, 4)
>> +     #define TSENSOR_CFG_REG2_REBOOT_TIME    GENMASK(23, 16)
>> +     #define TSENSOR_CFG_REG2_ENABLE         \
>> +             (TSENSOR_CFG_REG2_HITEMP_EN |   \
>> +              TSENSOR_CFG_REG2_REBOOT_EN |   \
>> +              TSENSOR_CFG_REG2_REBOOT_TIME)
>> +
>> +#define TSENSOR_TEMP_CAL             1
>> +
>>   #define TSENSOR_STAT0                       0x40
>>
>>   #define TSENSOR_STAT9                       0x64
>> @@ -63,6 +75,7 @@
>>
>>   #define TSENSOR_CALIB_OFFSET        1
>>   #define TSENSOR_CALIB_SHIFT 4
>> +#define TSENSOR_HW_RESET_DEFAULT_TEMP        110000
>>
>>   /**
>>    * struct amlogic_thermal_soc_calib_data
>> @@ -93,6 +106,7 @@ struct amlogic_thermal_data {
>>       const struct amlogic_thermal_soc_calib_data 
>> *calibration_parameters;
>>       const struct regmap_config *regmap_config;
>>       bool use_sm;
>> +     bool has_sysclk;
>>   };
>>
>>   struct amlogic_thermal {
>> @@ -101,8 +115,10 @@ struct amlogic_thermal {
>>       struct regmap *regmap;
>>       struct regmap *sec_ao_map;
>>       struct clk *clk;
>> +     struct clk *sysclk;
>>       struct thermal_zone_device *tzd;
>>       u32 trim_info;
>> +     u32 temp_code;
>>       struct meson_sm_firmware *sm_fw;
>>       u32 tsensor_id;
>>   };
>> @@ -138,6 +154,46 @@ static int 
>> amlogic_thermal_code_to_millicelsius(struct amlogic_thermal *pdata,
>>       return temp;
>>   }
>>
>> +/*
>> + * Calculate a temperature code from a temperature value .
>> + * The unit of the temperature is degree milliCelsius.
>> + */
>> +static u32 amlogic_thermal_millicelsius_to_code(struct 
>> amlogic_thermal *pdata, int millicelsius)
>> +{
>> +     const struct amlogic_thermal_soc_calib_data *param =
>> +                                     
>> pdata->data->calibration_parameters;
>> +     s64 factor, uptat, uefuse;
>> +     u32 temp_code;
>> +
>> +     uefuse = pdata->trim_info & TSENSOR_TRIM_SIGN_MASK ?
>> +                          ~(pdata->trim_info & 
>> TSENSOR_TRIM_TEMP_MASK) + 1 :
>> +                          (pdata->trim_info & TSENSOR_TRIM_TEMP_MASK);
>> +
>> +     factor = param->B + div_s64(millicelsius, 100);
>> +     factor = BIT(16) * factor;
>> +     factor = div_s64(factor, param->A);
>> +     factor = factor - (uefuse & TSENSOR_TRIM_TEMP_MASK);
>> +
>> +     uptat = param->n * factor;
>> +     uptat = div_s64(uptat, BIT(16));
>> +     uptat = param->m - uptat;
>> +
>> +     factor = factor * 100;
>> +     factor = div_s64(factor, uptat);
>> +
>> +     temp_code = ((factor >> 0x4) & TSENSOR_TEMP_MASK) + 
>> TSENSOR_TEMP_CAL;
>> +
>> +     return temp_code;
>> +}
>> +
>> +static void amlogic_tsensor_setup_hw_reset(struct amlogic_thermal *data)
>> +{
>> +     regmap_update_bits(data->regmap, TSENSOR_CFG_REG2, 
>> TSENSOR_CFG_REG2_REBOOT_CODE,
>> +                        data->temp_code << 0x4);
>> +     regmap_update_bits(data->regmap, TSENSOR_CFG_REG2,
>> +                        TSENSOR_CFG_REG2_ENABLE, 
>> TSENSOR_CFG_REG2_ENABLE);
>> +}
>> +
>>   static int amlogic_thermal_enable(struct amlogic_thermal *data)
>>   {
>>       int ret;
>> @@ -254,6 +310,13 @@ static const struct 
>> amlogic_thermal_soc_calib_data amlogic_thermal_g12a = {
>>       .n = 324,
>>   };
>>
>> +static const struct amlogic_thermal_soc_calib_data amlogic_thermal_a9 
>> = {
>> +     .A = 9164,
>> +     .B = 2747,
>> +     .m = 370,
>> +     .n = 270,
>> +};
>> +
>>   static const struct amlogic_thermal_data 
>> amlogic_thermal_g12a_cpu_param = {
>>       .u_efuse_off = 0x128,
>>       .calibration_parameters = &amlogic_thermal_g12a,
>> @@ -272,6 +335,13 @@ static const struct amlogic_thermal_data 
>> amlogic_thermal_a1_cpu_param = {
>>       .regmap_config = &amlogic_thermal_regmap_config_g12a,
>>   };
>>
>> +static const struct amlogic_thermal_data amlogic_thermal_a9_param = {
>> +     .use_sm                 = true,
>> +     .has_sysclk             = true,
>> +     .calibration_parameters = &amlogic_thermal_a9,
>> +     .regmap_config          = &amlogic_thermal_regmap_config_g12a,
>> +};
>> +
>>   static const struct amlogic_thermal_data amlogic_thermal_t7_param = {
>>       .use_sm                 = true,
>>       .calibration_parameters = &amlogic_thermal_g12a,
>> @@ -291,6 +361,10 @@ static const struct of_device_id 
>> of_amlogic_thermal_match[] = {
>>               .compatible = "amlogic,a1-cpu-thermal",
>>               .data = &amlogic_thermal_a1_cpu_param,
>>       },
>> +     {
>> +             .compatible = "amlogic,a9-thermal",
>> +             .data = &amlogic_thermal_a9_param,
>> +     },
>>       {
>>               .compatible = "amlogic,t7-thermal",
>>               .data = &amlogic_thermal_t7_param,
>> @@ -305,6 +379,7 @@ static int amlogic_thermal_probe(struct 
>> platform_device *pdev)
>>       struct device *dev = &pdev->dev;
>>       void __iomem *base;
>>       int ret;
>> +     u32 reset_temp;
>>
>>       pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
>>       if (!pdata)
>> @@ -323,9 +398,24 @@ static int amlogic_thermal_probe(struct 
>> platform_device *pdev)
>>       if (IS_ERR(pdata->regmap))
>>               return PTR_ERR(pdata->regmap);
>>
>> -     pdata->clk = devm_clk_get(dev, NULL);
>> -     if (IS_ERR(pdata->clk))
>> -             return dev_err_probe(dev, PTR_ERR(pdata->clk), "failed 
>> to get clock\n");
>> +     if (pdata->data->has_sysclk) {
>> +             pdata->clk = devm_clk_get(dev, "core");
>> +             if (IS_ERR(pdata->clk))
>> +                     return dev_err_probe(dev, PTR_ERR(pdata->clk), 
>> "failed to get core clk\n");
>> +             pdata->sysclk = devm_clk_get_enabled(dev, "pclk");
>> +             if (IS_ERR(pdata->sysclk))
>> +                     return dev_err_probe(dev, 
>> PTR_ERR(pdata->sysclk), "failed to get pclk\n");
>> +     } else {
>> +             pdata->clk = devm_clk_get(dev, NULL);
>> +             if (IS_ERR(pdata->clk))
>> +                     return dev_err_probe(dev, PTR_ERR(pdata->clk), 
>> "failed to get clock\n");
>> +     }
>> +
>> +     if (of_property_read_u32(pdev->dev.of_node, 
>> "amlogic,hw-reset-temp", &reset_temp)) {
>> +             dev_dbg(dev, "using default hardware reset temperature\n");
>> +             reset_temp = TSENSOR_HW_RESET_DEFAULT_TEMP;
>> +     }
> 
> Old SoC without the 'amlogic,hw-reset-temp' will now default to
> TSENSOR_HW_RESET_DEFAULT_TEMP
> 

This restart temperature setting is available on all chips, but it was 
not supported before. Here, a default value has been added.

>> +
>>
>>       if (pdata->data->use_sm)
>>               ret = amlogic_thermal_probe_sm(pdev, pdata);
>> @@ -346,6 +436,10 @@ static int amlogic_thermal_probe(struct 
>> platform_device *pdev)
>>
>>       devm_thermal_add_hwmon_sysfs(&pdev->dev, pdata->tzd);
>>
>> +     pdata->temp_code = amlogic_thermal_millicelsius_to_code(pdata, 
>> reset_temp);
>> +
>> +     amlogic_tsensor_setup_hw_reset(pdata);
> 
> Somehow related to the above comment, should it be only for A9 ?
> 

I will add corresponding commont to describe it.

>> +
>>       ret = amlogic_thermal_enable(pdata);
>>
>>       return ret;
>> @@ -355,6 +449,8 @@ static void amlogic_thermal_remove(struct 
>> platform_device *pdev)
>>   {
>>       struct amlogic_thermal *data = platform_get_drvdata(pdev);
>>
>> +     if (data->data->has_sysclk)
>> +             clk_disable_unprepare(data->sysclk);
> 
> Not needed, devm_ is used in the probe function
> 
Indeed, I will remove it.

>>       amlogic_thermal_disable(data);
>>   }
>>
>> @@ -363,6 +459,8 @@ static int amlogic_thermal_suspend(struct device 
>> *dev)
>>       struct amlogic_thermal *data = dev_get_drvdata(dev);
>>
>>       amlogic_thermal_disable(data);
>> +     if (data->data->has_sysclk)
>> +             clk_disable_unprepare(data->sysclk);
>>
>>       return 0;
>>   }
>> @@ -371,6 +469,9 @@ static int amlogic_thermal_resume(struct device *dev)
>>   {
>>       struct amlogic_thermal *data = dev_get_drvdata(dev);
>>
>> +     amlogic_tsensor_setup_hw_reset(data);
>> +     if (data->data->has_sysclk)
>> +             clk_prepare_enable(data->sysclk);
> 
> Shouldn't the clock enabled before accessing the register in
> amlogic_tsensor_setup_hw_reset() ?
>

Will do.


>>       return amlogic_thermal_enable(data);
>>   }
>>

_______________________________________________
linux-amlogic mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-amlogic