Re: [PATCH 1/2] ARM: dts: Correct white-space style
Michal Simek <[email protected]>
| Newsgroups | org.infradead.lists.linux-arm-kernel,dev.linux.lists.asahi,org.infradead.lists.linux-amlogic,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-kernel,org.kernel.vger.linux-tegra |
|---|---|
| Message-ID | <[email protected]> |
On 8/1/26 23:02, Krzysztof Kozlowski wrote:
> Correct a few white-space issues, like missing space before bracket '{'
> character or spurious space, which will be flagged by dt-check-style
> ("redundant-whitespace" warning). No functional changes.
>
> Signed-off-by: Krzysztof Kozlowski <[email protected]>
>
> ---
>
> I'll take this directly via soc@.
> ---
> arch/arm/boot/dts/armv7-m.dtsi | 2 +-
> arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts | 2 +-
> arch/arm/boot/dts/marvell/kirkwood-nsa320.dts | 4 ++--
> arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts | 8 ++++----
> arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi | 2 +-
> arch/arm/boot/dts/microchip/at91rm9200ek.dts | 2 +-
> arch/arm/boot/dts/microchip/lan966x-pcb8291.dts | 2 +-
> arch/arm/boot/dts/st/stih407-family.dtsi | 2 +-
> arch/arm/boot/dts/st/stm32mp135f-dk.dts | 2 +-
> arch/arm/boot/dts/xilinx/zynq-cc108.dts | 4 ++--
> 10 files changed, 15 insertions(+), 15 deletions(-)
>
> diff --git a/arch/arm/boot/dts/armv7-m.dtsi b/arch/arm/boot/dts/armv7-m.dtsi
> index 26f5443d85e1..6ee18d6a93ef 100644
> --- a/arch/arm/boot/dts/armv7-m.dtsi
> +++ b/arch/arm/boot/dts/armv7-m.dtsi
> @@ -1,6 +1,6 @@
> // SPDX-License-Identifier: GPL-2.0
> / {
> - nvic: interrupt-controller@e000e100 {
> + nvic: interrupt-controller@e000e100 {
> compatible = "arm,armv7m-nvic";
> interrupt-controller;
> #interrupt-cells = <1>;
> diff --git a/arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts
> index 74161b76008a..6c4131b846c1 100644
> --- a/arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts
> @@ -141,7 +141,7 @@ mdio@200 {
> #address-cells = <1>;
> #size-cells = <0>;
>
> - switch@0 {
> + switch@0 {
> compatible = "brcm,bcm53125";
> #address-cells = <1>;
> #size-cells = <0>;
> diff --git a/arch/arm/boot/dts/marvell/kirkwood-nsa320.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa320.dts
> index dd5c8ffc8781..56334b71152d 100644
> --- a/arch/arm/boot/dts/marvell/kirkwood-nsa320.dts
> +++ b/arch/arm/boot/dts/marvell/kirkwood-nsa320.dts
> @@ -30,12 +30,12 @@ pinctrl: pin-controller@10000 {
>
> /* SATA Activity and Present pins are not connected */
> pmx_sata0: pmx-sata0 {
> - marvell,pins ;
> + marvell,pins;
> marvell,function = "sata0";
> };
>
> pmx_sata1: pmx-sata1 {
> - marvell,pins ;
> + marvell,pins;
> marvell,function = "sata1";
> };
>
> diff --git a/arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts b/arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts
> index fec7269088d1..19a286dcc8a5 100644
> --- a/arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts
> +++ b/arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts
> @@ -35,7 +35,7 @@ led-4 {
> };
> };
>
> - led-controller-2 {
> + led-controller-2 {
> compatible = "gpio-leds";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_led_red
> @@ -58,7 +58,7 @@ led-6 {
> gpio-keys {
> compatible = "gpio-keys";
> pinctrl-names = "default" , "default", "default",
> - "default", "default" ;
> + "default", "default";
> pinctrl-0 = <&pinctrl_key_gpio_default>;
> pinctrl-1 = <&pinctrl_pio_rf &pinctrl_pio_wifi>;
> pinctrl-2 = <&pinctrl_pio_io_boot
> @@ -170,7 +170,7 @@ verbose_bootloader {
> input;
> };
>
> - nail_bed_detection {
> + nail_bed_detection {
> label = "nail bed detection";
> gpio = <&pioA PIN_PB12 GPIO_ACTIVE_HIGH>;
> input;
> @@ -276,7 +276,7 @@ &uart4 {
> &flx0 {
> status = "okay";
>
> - uart5: serial@200 {
> + uart5: serial@200 {
> status = "okay";
> };
> };
> diff --git a/arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi
> index 465664628419..75d2e748a3db 100644
> --- a/arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi
> +++ b/arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi
> @@ -298,7 +298,7 @@ &flx0 {
> atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
> status = "disabled";
>
> - uart5: serial@200 {
> + uart5: serial@200 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_flx0_default>;
> atmel,use-dma-rx;
> diff --git a/arch/arm/boot/dts/microchip/at91rm9200ek.dts b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
> index ce691c4692b9..b849bc7049d6 100644
> --- a/arch/arm/boot/dts/microchip/at91rm9200ek.dts
> +++ b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
> @@ -117,7 +117,7 @@ kernel@50000 {
> reg = <0x50000 0x300000>;
> };
>
> - root@350000 {
> + root@350000 {
> label = "root";
> reg = <0x350000 0x4B0000>;
> };
> diff --git a/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts b/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts
> index 3a3d76af8612..1f0b0b647aa9 100644
> --- a/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts
> +++ b/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts
> @@ -64,7 +64,7 @@ fc3_b_pins: fc3-b-pins {
> function = "fc3_b";
> };
>
> - can0_b_pins: can0-b-pins {
> + can0_b_pins: can0-b-pins {
> /* RX, TX */
> pins = "GPIO_35", "GPIO_36";
> function = "can0_b";
> diff --git a/arch/arm/boot/dts/st/stih407-family.dtsi b/arch/arm/boot/dts/st/stih407-family.dtsi
> index 08acba209c56..436fafd30317 100644
> --- a/arch/arm/boot/dts/st/stih407-family.dtsi
> +++ b/arch/arm/boot/dts/st/stih407-family.dtsi
> @@ -812,7 +812,7 @@ ethernet0: dwmac@9630000 {
> <&clk_s_c0_flexgen CLK_ETH_PHY>;
> };
>
> - mailbox0: mailbox@8f00000 {
> + mailbox0: mailbox@8f00000 {
> compatible = "st,stih407-mailbox";
> reg = <0x8f00000 0x1000>;
> interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
> index 6022e73f58af..1d6435c59096 100644
> --- a/arch/arm/boot/dts/st/stm32mp135f-dk.dts
> +++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
> @@ -382,7 +382,7 @@ goodix: goodix-ts@5d {
> VDDIO-supply = <&scmi_v3v3_sw>;
> touchscreen-size-x = <480>;
> touchscreen-size-y = <272>;
> - status = "okay" ;
> + status = "okay";
> };
> };
>
> diff --git a/arch/arm/boot/dts/xilinx/zynq-cc108.dts b/arch/arm/boot/dts/xilinx/zynq-cc108.dts
> index f5525c048426..e7cb82c7b8e6 100644
> --- a/arch/arm/boot/dts/xilinx/zynq-cc108.dts
> +++ b/arch/arm/boot/dts/xilinx/zynq-cc108.dts
> @@ -92,8 +92,8 @@ partition@f00000 {
>
> &sdhci1 {
> status = "okay";
> - broken-cd ;
> - wp-inverted ;
> + broken-cd;
> + wp-inverted;
> };
>
> &uart0 {
Reviewed-by: Michal Simek <[email protected]> # Zynq
M