[RESEND PATCH v7 15/16] arm64: dts: st: support Engicam MicroGEA-STM32MP257-RMM board

Dario Binacchi <[email protected]>
Newsgroups org.infradead.lists.linux-arm-kernel,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-kernel
Message-ID <[email protected]> 
Support for Engicam MicroGEA-STM32MP257-RMM board with:

 - 8 GB eMMC Flash
 - 2 GB LPDDR4 DRAM
 - CAN
 - LEDs
 - LCD panel with touchscreen
 - Micro SD card connector
 - Audio codec
 - Buzzer

Signed-off-by: Dario Binacchi <[email protected]>

---

(no changes since v5)

Changes in v5:
- Fix touchscreen resolution to 480x854
- Fix SPI1 CS0 polarity to GPIO_ACTIVE_LOW

Changes in v2:
- Drop the clocks property from the sai1 node in stm32mp257-engicam-microgea-rmm.dts
  to avoid overriding the peripheral bus clock reference defined in the base
  SoC device tree. Suggested by Sashiko.
- Reference the existing labeled nodes directly at the root level using
  &sai1a and &sai1b in stm32mp257-engicam-microgea-rmm.dts instead of
  redefining the entire node structure and redeclaring the labels. Suggested by Sashiko.
- Drop the #clock-cells property from sai1a and remove the reference to sai1a from
  the clocks array in sai1b, relying strictly on the st,sync property to handle
  internal synchronization.

 arch/arm64/boot/dts/st/Makefile               |   1 +
 .../st/stm32mp257-engicam-microgea-rmm.dts    | 319 ++++++++++++++++++
 2 files changed, 320 insertions(+)
 create mode 100644 arch/arm64/boot/dts/st/stm32mp257-engicam-microgea-rmm.dts

diff --git a/arch/arm64/boot/dts/st/Makefile b/arch/arm64/boot/dts/st/Makefile
index 63908113ae36..386eca593c54 100644
--- a/arch/arm64/boot/dts/st/Makefile
+++ b/arch/arm64/boot/dts/st/Makefile
@@ -2,5 +2,6 @@
 dtb-$(CONFIG_ARCH_STM32) += \
 	stm32mp215f-dk.dtb \
 	stm32mp235f-dk.dtb \
+	stm32mp257-engicam-microgea-rmm.dtb \
 	stm32mp257f-dk.dtb \
 	stm32mp257f-ev1.dtb
diff --git a/arch/arm64/boot/dts/st/stm32mp257-engicam-microgea-rmm.dts b/arch/arm64/boot/dts/st/stm32mp257-engicam-microgea-rmm.dts
new file mode 100644
index 000000000000..3aea0c2f6651
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp257-engicam-microgea-rmm.dts
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2026 Amarula Solutions, Dario Binacchi <[email protected]>
+ * Copyright (C) 2026 Engicam srl
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "stm32mp257-engicam-microgea.dtsi"
+
+/ {
+	model = "Engicam MicroGEA STM32MP257D RMM Board";
+	compatible = "engicam,microgea-stm32mp257-rmm",
+		     "engicam,microgea-stm32mp257", "st,stm32mp257";
+
+	aliases {
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		serial0 = &usart2;
+		serial1 = &usart1;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		default-brightness-level = <85>;
+		pwms = <&pwm2 0 100000 0>;
+	};
+
+	buzzer {
+		compatible = "pwm-beeper";
+		pwms = <&pwm4 0 1000000 0>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer {
+			compatible = "simple-framebuffer";
+			clocks = <&rcc CK_BUS_LTDC>, <&rcc CK_KER_LTDC>;
+			lcd-supply = <&reg_3v3>;
+			status = "disabled";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			gpios = <&gpioh 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			status = "okay";
+		};
+
+		led-1 {
+			gpios = <&gpioh 6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			status = "okay";
+		};
+	};
+
+	mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_ext_pwr: regulator-ext-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "ext-pwr";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP25-RMM";
+		widgets = "Headphone", "Headphone Jack",
+			  "Microphone", "Microphone Jack";
+		routing = "Headphone Jack", "HP_OUT",
+			  "MIC_IN", "Microphone Jack",
+			  "Microphone Jack", "Mic Bias";
+		dais = <&sai1a_port &sai1b_port>;
+		status = "okay";
+	};
+};
+
+&arm_wdt {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		interrupt-parent = <&gpiob>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpiod 1 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <854>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&mclk>;
+
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+
+		sgtl5000_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sgtl5000_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai1a_endpoint>;
+				frame-master = <&sgtl5000_tx_endpoint>;
+				bitclock-master = <&sgtl5000_tx_endpoint>;
+			};
+
+			sgtl5000_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai1b_endpoint>;
+				frame-master = <&sgtl5000_rx_endpoint>;
+				bitclock-master = <&sgtl5000_rx_endpoint>;
+			};
+		};
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-1 = <&ltdc_sleep_pins_a>;
+	status = "okay";
+
+	port {
+		ltdc_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&sai1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai1a_pins_a>, <&sai1b_pins_a>;
+	pinctrl-1 = <&sai1a_sleep_pins_a>, <&sai1b_sleep_pins_a>;
+	status = "okay";
+};
+
+&sai1a {
+	dma-names = "tx";
+	status = "okay";
+
+	sai1a_port: port {
+		sai1a_endpoint: endpoint {
+			remote-endpoint = <&sgtl5000_tx_endpoint>;
+			dai-format = "i2s";
+			mclk-fs = <512>;
+		};
+	};
+};
+
+&sai1b {
+	dma-names = "rx";
+	st,sync = <&sai1a 2>;
+	clocks = <&rcc CK_KER_SAI1>;
+	clock-names = "sai_ck";
+	status = "okay";
+
+	sai1b_port: port {
+		sai1b_endpoint: endpoint {
+			remote-endpoint = <&sgtl5000_rx_endpoint>;
+			dai-format = "i2s";
+			mclk-fs = <512>;
+		};
+	};
+};
+
+/* MicroSD */
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&scmi_v3v3>;
+	vqmmc-supply = <&scmi_vddio1>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi1_pins_a>;
+	pinctrl-1 = <&spi1_sleep_pins_a>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpioh 8 GPIO_ACTIVE_LOW>, <&gpioh 3 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	display: display@0 {
+		compatible = "rocktech,rk050hr345-ct106a", "ilitek,ili9806e";
+		reg = <0>;
+		vdd-supply = <&reg_3v3>;
+		spi-max-frequency = <10000000>;
+		reset-gpios = <&gpiob 6 GPIO_ACTIVE_LOW>;
+		backlight = <&backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&ltdc_out>;
+			};
+		};
+	};
+};
+
+&timers2 {
+	status = "okay";
+
+	pwm2: pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-1 = <&pwm2_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
+
+&timers4 {
+	status = "okay";
+
+	pwm4: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm4_pins_a>;
+		pinctrl-1 = <&pwm4_sleep_pins_a>;
+		status = "okay";
+	};
+};
+
+&usart1 {
+	pinctrl-names = "default", "idle", "sleep";
+	pinctrl-0 = <&usart1_pins_b>;
+	pinctrl-1 = <&usart1_idle_pins_b>;
+	pinctrl-2 = <&usart1_sleep_pins_b>;
+	/delete-property/ dmas;
+	/delete-property/ dma-names;
+	status = "okay";
+};
+
+&usart2 {
+	pinctrl-names = "default", "idle", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_idle_pins_a>;
+	pinctrl-2 = <&usart2_sleep_pins_a>;
+	/delete-property/ dmas;
+	/delete-property/ dma-names;
+	status = "okay";
+};
-- 
2.43.0
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.