Re: [PATCH v3 15/15] ARM: dts: qcom: Add initial device tree for Kuno SoC

On 26-08-21 21:39:08, Hardeep Sharma wrote:
> Add SoC-level DTSI (qcom-kuno.dtsi) and IDP board DTS
> (qcom-kuno-idp.dts) for the Qualcomm Kuno SoC.
> 
> Peripherals included in this initial set:
>   - Single Cortex-A7 CPU with PSCI idle states
>   - RPMh RSC with clock controller, power domains, and BCM voter
>   - GCC (Global Clock Controller)
>   - TLMM pin controller (110 GPIOs)
>   - Interconnect (aggre-noc, cnoc-main)
>   - GENI UART console (QUP SE3)
>   - SMEM, hardware spinlocks (TCSR mutex)
> 
> Reviewed-by: Dmitry Baryshkov <[email protected]>
> Reviewed-by: Linus Walleij <[email protected]>
> Signed-off-by: Hardeep Sharma <[email protected]>
> ---
>  arch/arm/boot/dts/qcom/Makefile          |   1 +
>  arch/arm/boot/dts/qcom/qcom-kuno-idp.dts |  25 ++
>  arch/arm/boot/dts/qcom/qcom-kuno.dtsi    | 422 +++++++++++++++++++++++++++++++
>  3 files changed, 448 insertions(+)
> 

[...]

> diff --git a/arch/arm/boot/dts/qcom/qcom-kuno.dtsi b/arch/arm/boot/dts/qcom/qcom-kuno.dtsi
> new file mode 100644
> index 000000000000..d430e65e08bf
> --- /dev/null
> +++ b/arch/arm/boot/dts/qcom/qcom-kuno.dtsi
> @@ -0,0 +1,422 @@
> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +/*
> + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
> + */
> +
> +#include <dt-bindings/clock/qcom,kuno-gcc.h>
> +#include <dt-bindings/clock/qcom,rpmh.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom,rpmhpd.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/soc/qcom,rpmh-rsc.h>
> +
> +/ {
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +	interrupt-parent = <&intc>;
> +
> +	clocks {
> +		xo_board: xo-board {
> +			compatible = "fixed-clock";
> +			clock-frequency = <38400000>;
> +			#clock-cells = <0>;
> +		};
> +
> +		sleep_clk: sleep-clk {
> +			compatible = "fixed-clock";
> +			clock-frequency = <32000>;
> +			#clock-cells = <0>;
> +		};
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu0: cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a7";
> +			reg = <0x0>;
> +			enable-method = "psci";
> +			cpu-idle-states = <&little_cpu_sleep_0>, <&little_cpu_sleep_1>;

Nit: we usually put these on separate lines.

The rest looks good, so:

Reviewed-by: Abel Vesa <[email protected]>