[PATCH v2 1/2] dt-bindings: phy: ti,phy-usb3: Add aspcie reference clock setting

The PHY control logic in the OMAP PCIe PHY subsystem has a
configurable reference clock selection. It can either use
the ljcb_clkp/ljcb_clkn pin as inputs, recovering the clock
from the bus (RX mode), or generate the reference clock
internally, driving the bus pins as outputs (TX mode).

The setting is exposed through a register in a system controller.
A device tree property is added to specify the syscon node,
register offset and mode value.

Signed-off-by: David Oberhollenzer <[email protected]>
---
 .../devicetree/bindings/phy/ti,phy-usb3.yaml  | 39 +++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/ti,phy-usb3.yaml b/Documentation/devicetree/bindings/phy/ti,phy-usb3.yaml
index 84f538aa587c..11787b042345 100644
--- a/Documentation/devicetree/bindings/phy/ti,phy-usb3.yaml
+++ b/Documentation/devicetree/bindings/phy/ti,phy-usb3.yaml
@@ -52,6 +52,20 @@ properties:
       enum: [wkupclk, sysclk, refclk, dpll_ref,
              dpll_ref_m2, phy-div, div-clk]
 
+  ti,syscon-acspcie-tx-rx:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: |
+      Syscon register and setting to configure the clock buffer to run
+      in RX mode (clock pins are inputs, the clock is recovered from
+      the bus), or in TX mode (pins are outputs, internal reference
+      clock drives the bus).
+    maxItems: 1
+    items:
+      items:
+        - description: Phandle to the system control module
+        - description: Register offset of CTRL_CORE_SMA_SW_6
+        - description: Setting for PCIE_TX_RX_CONTROL
+
   syscon-phy-power:
     $ref: /schemas/types.yaml#/definitions/phandle-array
     maxItems: 1
@@ -94,6 +107,17 @@ allOf:
     else:
       properties:
         syscon-pllreset: false
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ti,phy-pipe3-pcie
+    then:
+      properties:
+        ti,syscon-acspcie-tx-rx: true
+    else:
+      properties:
+        ti,syscon-acspcie-tx-rx: false
 
 required:
   - reg
@@ -135,4 +159,19 @@ examples:
         syscon-pllreset = <&scm_conf 0x3fc>;
         #phy-cells = <0>;
     };
+
+  - |
+    /* TI PIPE3 PCIE PHY */
+    pcie-phy@4a0a4000 {
+        compatible = "ti,phy-pipe3-pcie";
+        reg = <0x4a0a4000 0x80>,  /* phy_rx */
+              <0x4a0a4400 0x64>;  /* phy_tx */
+        reg-names = "phy_rx", "phy_tx";
+        clocks = <&dpll_pcie_ref_ck>, <&dpll_pcie_ref_m2ldo_ck>;
+        clock-names = "dpll_ref", "dpll_ref_m2";
+        #phy-cells = <0>;
+        syscon-phy-power = <&scm_conf_pcie 0x1c>;
+        syscon-pcs = <&scm_conf_pcie 0x10>;
+        ti,syscon-acspcie-tx-rx = <&scm_conf1 0x10 0x2>;
+    };
 ...
-- 
2.55.0


-- 
linux-phy mailing list
[email protected]
https://lists.infradead.org/mailman/listinfo/linux-phy