Re: [PATCH 09/10] ARM: dts: qcom: msm8974: add the USB3 controller and its PHYs
Konrad Dybcio <[email protected]>
| Newsgroups | org.infradead.lists.linux-phy,org.kernel.vger.linux-arm-msm,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-kernel,org.kernel.vger.linux-usb |
|---|---|
| Message-ID | <[email protected]> |
On 8/10/26 1:42 PM, Dmitry Baryshkov wrote:
> The primary USB port of MSM8974 - a Synopsys DWC3 behind the standard
> Qualcomm wrapper - is not described, so boards can only use the two
> ChipIdea controllers.
[...]
> arch/arm/boot/dts/qcom/qcom-msm8974.dtsi | 47 ++++++++++++++++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
> index 06c0af0aa317..bac3c8772e0a 100644
> --- a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
> @@ -713,6 +713,53 @@ blsp2_i2c6: i2c@f9968000 {
> #size-cells = <0>;
> };
>
> + usb3: usb@f9200000 {
> + compatible = "qcom,msm8974-dwc3", "qcom,snps-dwc3";
> + reg = <0xf9200000 0xfc000>;
> + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "dwc_usb3", "pwr_event",
> + "hs_phy_irq";
1 a line (also in a couple cases below)
> + clocks = <&gcc GCC_SYS_NOC_USB3_AXI_CLK>,
> + <&gcc GCC_USB30_MASTER_CLK>,
> + <&gcc GCC_USB30_SLEEP_CLK>,
> + <&gcc GCC_USB30_MOCK_UTMI_CLK>;
> + clock-names = "cfg_noc", "core", "sleep", "mock_utmi";
> + assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB30_MASTER_CLK>;
> + assigned-clock-rates = <60000000>, <125000000>;
> + resets = <&gcc GCC_USB_30_BCR>;
> + phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
> + phy-names = "usb2-phy", "usb3-phy";
> + snps,dis_u2_susphy_quirk;
> + snps,dis_enblslpm_quirk;
We usually have 10x as many quirks here, I guess +Wesley may not remember
the suitable values at this point, but I think he mentioned there is a set
of "common defaults"
> + status = "disabled";
\n before status, please
Needs power-domains + required-opps
> + };
> +
> + usb3_hs_phy: phy@f92f8800 {
I don't like re-claiming the memory space.. Should we make these PHYs the
subnodes of the qc glue?
Konrad
--
linux-phy mailing list
[email protected]
https://lists.infradead.org/mailman/listinfo/linux-phy