[PATCH v4 3/7] phy: rockchip-samsung-dcphy: Move block-level setup to runtime resume

From: Jason Yang <[email protected]>

The APB reset and the BIAS references have to be treated as block-level
[1]: both the transmitter and the receiver need them, and they only have
to be programmed once. They are programmed from the transmitter's
power-on path today. A later change registers one struct phy for each of
them, and a second consumer coming up would then reset the block
underneath a PHY that is already running.

Program them from runtime resume instead, where whichever of the two
comes up first brings the block up and a second one no longer resets it.
This puts the BIAS writes ahead of the per-PHY reset assert, where the
TRM's worked example has them after [1]. That is safe: neither M_RESETN
nor S_RESETN covers the BIAS registers, and the values written are those
registers' reset defaults.

The output level select in BIAS_CON4 stays on the power-on path: it
selects 400mV for D-PHY and 530mV for C-PHY, and the driver core resumes
a runtime-PM supplier before the consumer's probe runs, so runtime resume
cannot yet know which of the two applies.

[1] RK3588 TRM: sections 22.4.1 (address map), 22.4.2 (reset values),
    22.6.1.2 (reset) and 22.6.4.1 (D-PHY transmitter start-up)

Signed-off-by: Jason Yang <[email protected]>
---
 drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c | 25 ++++++++++++-----------
 1 file changed, 13 insertions(+), 12 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c b/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
index 11e872cc6611..459ce882b369 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-dcphy.c
@@ -980,13 +980,6 @@ static void samsung_mipi_dcphy_bias_block_enable(struct samsung_mipi_dcphy *sams
 						 I_LADDER_1_00V);
 	regmap_write(samsung->regmap, BIAS_CON2, REG_325M_325MV | REG_LP_400M_400MV |
 						 REG_400M_400MV | REG_645M_645MV);
-
-	/* default output voltage select:
-	 * dphy: 400mv
-	 * cphy: 530mv
-	 */
-	regmap_update_bits(samsung->regmap, BIAS_CON4,
-			   I_MUX_SEL_MASK, I_MUX_400MV);
 }
 
 static void samsung_mipi_dphy_lane_enable(struct samsung_mipi_dcphy *samsung)
@@ -1338,7 +1331,13 @@ static int samsung_mipi_dphy_power_on(struct samsung_mipi_dcphy *samsung)
 
 	reset_control_assert(samsung->m_phy_rst);
 
-	samsung_mipi_dcphy_bias_block_enable(samsung);
+	/* default output voltage select:
+	 * dphy: 400mv
+	 * cphy: 530mv
+	 */
+	regmap_update_bits(samsung->regmap, BIAS_CON4,
+			   I_MUX_SEL_MASK, I_MUX_400MV);
+
 	samsung_mipi_dcphy_pll_configure(samsung);
 	samsung_mipi_dphy_clk_lane_timing_init(samsung);
 	samsung_mipi_dphy_data_lane_timing_init(samsung);
@@ -1362,10 +1361,6 @@ static int samsung_mipi_dcphy_power_on(struct phy *phy)
 {
 	struct samsung_mipi_dcphy *samsung = phy_get_drvdata(phy);
 
-	reset_control_assert(samsung->apb_rst);
-	udelay(1);
-	reset_control_deassert(samsung->apb_rst);
-
 	switch (samsung->type) {
 	case PHY_TYPE_DPHY:
 		return samsung_mipi_dphy_power_on(samsung);
@@ -1656,6 +1651,12 @@ static __maybe_unused int samsung_mipi_dcphy_runtime_resume(struct device *dev)
 		return ret;
 	}
 
+	reset_control_assert(samsung->apb_rst);
+	udelay(1);
+	reset_control_deassert(samsung->apb_rst);
+
+	samsung_mipi_dcphy_bias_block_enable(samsung);
+
 	return 0;
 }
 

-- 
2.43.0



-- 
linux-phy mailing list
[email protected]
https://lists.infradead.org/mailman/listinfo/linux-phy