Re: [PATCH v4 2/8] clk: starfive: Add system-0 domain PLL clock driver

Hi, Brian

> Hi Changhuang,
> 
> On Sat, Aug 08, 2026 at 06:50:48PM -0700, Changhuang Liang wrote:
> > Add system-0 domain PLL clock driver for StarFive JHB100 SoC.
> >
> > Signed-off-by: Changhuang Liang <[email protected]>
> > ---
> >  drivers/clk/starfive/Kconfig                  |   8 +
> >  drivers/clk/starfive/Makefile                 |   1 +
> >  .../clk/starfive/clk-starfive-jhb100-pll.c    | 535 ++++++++++++++++++
> >  3 files changed, 544 insertions(+)
> >  create mode 100644 drivers/clk/starfive/clk-starfive-jhb100-pll.c
> >
> > diff --git a/drivers/clk/starfive/Kconfig
> > b/drivers/clk/starfive/Kconfig index 852464949334..a39dd22112fa 100644
> > --- a/drivers/clk/starfive/Kconfig
> > +++ b/drivers/clk/starfive/Kconfig
> > @@ -117,6 +117,14 @@ config CLK_STARFIVE_JHB100_PER3
> >  	  Say yes here to support the peripheral-3 clock controller
> >  	  on the StarFive JHB100 SoC.
> >
> > +config CLK_STARFIVE_JHB100_PLL
> > +	bool "StarFive JHB100 PLL clock support"
> 
> Can this be a tristate?

I checked again, this doesn't affect the critical clock, so it can be changed to tristate

> 
> > +	depends on ARCH_STARFIVE || COMPILE_TEST
> > +	default ARCH_STARFIVE
> > +	help
> > +	  Say yes here to support the PLL clock controller on the
> > +	  StarFive JHB100 SoC.
> > +
> >  config CLK_STARFIVE_JHB100_SYS0
> >  	bool "StarFive JHB100 system-0 clock support"
> >  	depends on ARCH_STARFIVE || COMPILE_TEST diff --git
> > a/drivers/clk/starfive/Makefile b/drivers/clk/starfive/Makefile index
> > f00690f0cdad..547a8c170728 100644
> > --- a/drivers/clk/starfive/Makefile
> > +++ b/drivers/clk/starfive/Makefile
> > @@ -15,6 +15,7 @@ obj-$(CONFIG_CLK_STARFIVE_JHB100_PER0)
> 	+= clk-starfive-jhb100-per0.o
> >  obj-$(CONFIG_CLK_STARFIVE_JHB100_PER1)		+=
> clk-starfive-jhb100-per1.o
> >  obj-$(CONFIG_CLK_STARFIVE_JHB100_PER2)		+=
> clk-starfive-jhb100-per2.o
> >  obj-$(CONFIG_CLK_STARFIVE_JHB100_PER3)		+=
> clk-starfive-jhb100-per3.o
> > +obj-$(CONFIG_CLK_STARFIVE_JHB100_PLL)		+=
> clk-starfive-jhb100-pll.o
> >  obj-$(CONFIG_CLK_STARFIVE_JHB100_SYS0)		+=
> clk-starfive-jhb100-sys0.o
> >  obj-$(CONFIG_CLK_STARFIVE_JHB100_SYS1)		+=
> clk-starfive-jhb100-sys1.o
> >  obj-$(CONFIG_CLK_STARFIVE_JHB100_SYS2)		+=
> clk-starfive-jhb100-sys2.o
> > diff --git a/drivers/clk/starfive/clk-starfive-jhb100-pll.c
> > b/drivers/clk/starfive/clk-starfive-jhb100-pll.c
> > new file mode 100644
> > index 000000000000..55d589bc831e
> > --- /dev/null
> > +++ b/drivers/clk/starfive/clk-starfive-jhb100-pll.c
> > @@ -0,0 +1,535 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * StarFive JHB100 PLL Clock Generator Driver
> > + *
> > + * Copyright (C) 2024 StarFive Technology Co., Ltd.
> > + *
> > + * Author: Changhuang Liang <[email protected]>
> > + */
> > +
> > +#include <linux/bits.h>
> > +#include <linux/clk-provider.h>
> > +#include <linux/debugfs.h>
> > +#include <linux/device.h>
> > +#include <linux/kernel.h>
> > +#include <linux/math64.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/units.h>
> > +
> > +#include <dt-bindings/clock/starfive,jhb100-crg.h>
> > +
> > +/* this driver expects a 25MHz input frequency from the oscillator */
> > +#define JHB100_PLL_OSC_RATE		(25 * HZ_PER_MHZ)
> > +
> > +/* System-0 domain PLL */
> > +#define JHB100_PLL2_OFFSET		0x00
> > +#define JHB100_PLL3_OFFSET		0x0c
> > +#define JHB100_PLL4_OFFSET		0x18
> > +#define JHB100_PLL5_OFFSET		0x24
> > +
> > +#define JHB100_PLL_CFG0_OFFSET		0x0
> > +#define JHB100_PLL_CFG1_OFFSET		0x4
> > +#define JHB100_PLL_CFG2_OFFSET		0x8
> > +
> > +#define JHB100_PLLX_CFG0(offset)	((offset) + JHB100_PLL_CFG0_OFFSET)
> > +/* fbdiv value should be 16 to 4095 */
> > +#define   JHB100_PLL_FBDIV			GENMASK(13, 2)
> > +#define   JHB100_PLL_FBDIV_SHIFT		2
> > +#define   JHB100_PLL_FOUTPOSTDIV_EN		BIT(14)
> > +#define   JHB100_PLL_FOUTPOSTDIV_EN_SHIFT	14
> > +#define   JHB100_PLL_FOUTVCOP_EN		BIT(16)
> > +#define   JHB100_PLL_FOUTVCOP_EN_SHIFT		16
> > +
> > +#define JHB100_PLLX_CFG1(offset)	((offset) + JHB100_PLL_CFG1_OFFSET)
> > +/* frac value should be decimals multiplied by 2^24 */
> > +#define   JHB100_PLL_FRAC			GENMASK(23, 0)
> > +#define   JHB100_PLL_FRAC_SHIFT			0
> > +#define   JHB100_PLL_LOCK			BIT(24)
> > +#define   JHB100_PLL_LOCK_SHIFT			24
> > +
> > +#define JHB100_PLLX_CFG2(offset)	((offset) + JHB100_PLL_CFG2_OFFSET)
> > +#define   JHB100_PLL_PD				BIT(13)
> > +#define   JHB100_PLL_PD_SHIFT			13
> > +#define   JHB100_PLL_POSTDIV			GENMASK(15, 14)
> > +#define   JHB100_PLL_POSTDIV_SHIFT		14
> > +#define   JHB100_PLL_REFDIV			GENMASK(23, 18)
> > +#define   JHB100_PLL_REFDIV_SHIFT		18
> > +
> > +#define JHB100_PLL_TIMEOUT_US		1000
> > +#define JHB100_PLL_INTERVAL_US		100
> > +
> > +struct jhb100_pll_preset {
> > +	unsigned long freq;
> > +	u32 frac;			/* frac value should be decimals multiplied by 2^24
> */
> > +	unsigned fbdiv		: 12;	/* fbdiv value should be 16 to 4095 */
> > +	unsigned refdiv		: 6;
> > +	unsigned postdiv	: 2;
> > +	unsigned foutpostdiv_en	: 1;
> > +	unsigned foutvcop_en	: 1;
> > +};
> > +
> > +struct jhb100_pll_info {
> > +	char *name;
> 
> const char *name ?

Will Fix.

Best Regards,
Changhuang



_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv