Re: [PATCH] riscv: defconfig: enable dwc3 and the SpacemiT K1 thermal sensor

On Tue, Aug 25, 2026 at 10:49:05PM +0000, Yixun Lan wrote:
> Hi Bruno,
> 
> On 07:22 Tue 25 Aug     , Bruno Banelli wrote:
> > Two blocks on SpacemiT K1 boards are unreachable from a stock defconfig
> > build:
> > 
> >  - USB_DWC3 is not enabled, so the dwc3 controller that drives all of
> >    the USB 3.0 ports on boards like the Milk-V Jupiter never probes.
> > 
> >  - SPACEMIT_K1_TSENSOR has no default in its Kconfig and is not listed
> >    here, so a K1 board comes up with no temperature readings at all,
> >    even though k1.dtsi describes five thermal zones.
> > 
> > Enable both.
> > 
> The patch itself looks good to me, but since it deal with two diferent drivers
> So, can you split it into two patches? which easy to review and manage

IMO it's fine being one patch, but this temp sensor should probably be a
module?

> 
> > Signed-off-by: Bruno Banelli <[email protected]>
> > ---
> >  arch/riscv/configs/defconfig | 3 +++
> >  1 file changed, 3 insertions(+)
> > 
> > diff --git a/arch/riscv/configs/defconfig b/arch/riscv/configs/defconfig
> > index 04ae305d5..03d9ac2f7 100644
> > --- a/arch/riscv/configs/defconfig
> > +++ b/arch/riscv/configs/defconfig
> > @@ -209,6 +209,8 @@ CONFIG_USB=y
> >  CONFIG_USB_OTG=y
> >  CONFIG_USB_XHCI_HCD=y
> >  CONFIG_USB_XHCI_PLATFORM=y
> > +CONFIG_USB_DWC3=y
> > +CONFIG_USB_DWC3_GENERIC_PLAT=y
> >  CONFIG_USB_EHCI_HCD=y
> >  CONFIG_USB_EHCI_HCD_PLATFORM=y
> >  CONFIG_USB_OHCI_HCD=y
> > @@ -260,6 +262,7 @@ CONFIG_CLK_SOPHGO_SG2042_PLL=y
> >  CONFIG_CLK_SOPHGO_SG2042_CLKGEN=y
> >  CONFIG_CLK_SOPHGO_SG2042_RPGATE=y
> >  CONFIG_SPACEMIT_K1_CCU=y
> > +CONFIG_SPACEMIT_K1_TSENSOR=y
> >  CONFIG_SPACEMIT_K3_CCU=y
> >  CONFIG_SUN8I_DE2_CCU=m
> >  CONFIG_SUN50I_IOMMU=y
> > 
> > base-commit: 66498c75b4f8017f62d720d9b59675bdf3abce91
> > -- 
> > 2.43.0
> > 
> 
> -- 
> Yixun Lan (dlan)

_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv

-----BEGIN PGP SIGNATURE-----

iHUEABYKAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCao6kxgAKCRB4tDGHoIJi
0v5VAQDYT8jhm+YKA8FT1Q7h0iuPmAOmrpY0WCsMjmlbUFM3SgD+NRQmA/aRKSzC
oKHb76m702nIoXoRdTDuwGBv8GgNbgE=
=XCwW
-----END PGP SIGNATURE-----