Re: [PATCH v2 3/4] drm/rockchip: lvds: add RK3568 support

On 7/24/2026 4:08 PM, Rok Markovic wrote:
> The RK3568 LVDS transmitter has no register block of its own. It is
> driven entirely through the GRF and re-uses the MIPI DSI0 D-PHY in
> PHY_MODE_LVDS, which phy-rockchip-inno-dsidphy already supports.
> 
> Based on Alibek Omarov's earlier posting [1], with the changes below.
> 
> Power the D-PHY from the encoder enable path rather than from probe.
> phy_power_on() runs the phy driver's whole LVDS bring-up: PLL and
> bandgap power-on, a settle, PLL mode select, then a reset pulse of the
> serializer and the lane enables. None of that is safe at probe time -
> the GRF has not yet switched the block to LVDS mode (LVDS0_MODE_EN is
> set from rk3568_lvds_poweron(), i.e. the enable path) and the VOP is
> not driving dclk. The serializer is clocked from dclk and latches its
> state coming out of that reset, so it comes up dead and stays dead.
> The failure is silent: every register in the phy, the GRF and the VOP
> reads back exactly as on a working system while the lanes sit at
> common mode and never toggle.
> 
> Program RK3568_LVDS0_DCLK_INV_SEL from the CRTC state's bus_flags so
> the panel's declared pixelclk-active is honoured on the LVDS block as
> well as on the VOP pin polarity. Both have to agree with the edge the
> panel samples on.
> 
> Re-assert RK3568_LVDS0_P2S_EN in rk3568_lvds_poweron().
> rk3568_lvds_poweroff() clears MODE_EN and P2S_EN together, so setting
> P2S_EN once at probe would leave the parallel-to-serial converter off
> after the first disable/enable cycle.
> 
> Use regmap_write() rather than regmap_update_bits() for the GRF. These
> registers are write-masked - the upper 16 bits select which of the
> lower 16 a write may change - so there is nothing to preserve and no
> reason to read first. Passing a FIELD_PREP_WM16() value as both the
> mask and the value of an update_bits() applies the masking twice and
> only works by accident.
> 
> Take no clock. The block exposes no MMIO of its own, so there is
> nothing for the DSI controller's APB clock to reach; the vendor BSP
> scans out LVDS with PCLK_DSITX_0's gate off, and so does this driver.
> 
> Between the above, nothing needs programming at probe at all: the GRF
> is written entirely from the enable path, so px30_lvds_probe() is left
> alone rather than being refactored into a shared phy helper.
> 
> Track the enabled state so that a .enable() that bails out unwinds
> itself and the .disable() that the atomic helpers still call afterwards
> becomes a no-op, rather than underflowing the phy power count and the
> runtime-PM count of an encoder that never came up.
> 
> [1] https://lore.kernel.org/all/[email protected]/
> 
> Co-developed-by: Alibek Omarov <[email protected]>
> Signed-off-by: Alibek Omarov <[email protected]>
> Signed-off-by: Rok Markovic <[email protected]>
> Assisted-by: Claude:claude-opus-4-8
> ---
> Changes in v2:
>   - Drop the clock. rk3568_lvds_poweron() no longer enables a pclk;
>     the block has no MMIO for the DSI APB clock to reach, and the
>     vendor BSP scans out with PCLK_DSITX_0 gated off.
>   - Merge rk3568_lvds_grf_config() into rk3568_lvds_poweron(): a
>     single masked write to VO_CON2 instead of two, and check the
>     output type before resuming runtime PM.
>   - Balance the enable/disable teardown so a .enable() that fails
>     partway does not underflow the phy power and runtime-PM counts
>     when the atomic helpers then call .disable().
>   - Use pm_runtime_resume_and_get(), matching the rk3288/px30 paths.
>   - Drop the in-code comments restating phy_set_mode() internals and
>     the write-masked GRF convention; the ordering rationale is in the
>     commit message.
> 
>  drivers/gpu/drm/rockchip/rockchip_lvds.c | 124 +++++++++++++++++++++++
>  drivers/gpu/drm/rockchip/rockchip_lvds.h |  10 ++
>  2 files changed, 134 insertions(+)
> 
> diff --git a/drivers/gpu/drm/rockchip/rockchip_lvds.c b/drivers/gpu/drm/rockchip/rockchip_lvds.c
> index 95fa0a9..9af21fc 100644
> --- a/drivers/gpu/drm/rockchip/rockchip_lvds.c
> +++ b/drivers/gpu/drm/rockchip/rockchip_lvds.c
> @@ -51,6 +51,7 @@ struct rockchip_lvds {
>  	struct regmap *grf;
>  	struct clk *pclk;
>  	struct phy *dphy;
> +	bool enabled;
>  	const struct rockchip_lvds_soc_data *soc_data;
>  	int output; /* rgb lvds or dual lvds output */
>  	int format; /* vesa or jeida format */
> @@ -435,6 +436,100 @@ static void px30_lvds_encoder_disable(struct drm_encoder *encoder)
>  	drm_panel_unprepare(lvds->panel);
>  }
>  
> +static int rk3568_lvds_poweron(struct drm_encoder *encoder)
> +{
> +	struct rockchip_lvds *lvds = encoder_to_lvds(encoder);
> +	struct rockchip_crtc_state *s =
> +		to_rockchip_crtc_state(encoder->crtc->state);
> +	bool negedge = !!(s->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE);
> +	int ret;
> +
> +	if (lvds->output != DISPLAY_OUTPUT_LVDS) {
> +		DRM_DEV_ERROR(lvds->dev, "Unsupported display output %d\n",
> +			      lvds->output);
> +		return -EINVAL;
> +	}
> +
> +	ret = pm_runtime_resume_and_get(lvds->dev);
> +	if (ret < 0) {
> +		DRM_DEV_ERROR(lvds->dev, "failed to get pm runtime: %d\n", ret);
> +		return ret;
> +	}
> +
> +	regmap_write(lvds->grf, RK3568_GRF_VO_CON2,
> +		     RK3568_LVDS0_MODE_EN(1) | RK3568_LVDS0_P2S_EN(1) |
> +		     RK3568_LVDS0_DCLK_INV_SEL(negedge));
> +	regmap_write(lvds->grf, RK3568_GRF_VO_CON0,
> +		     RK3568_LVDS0_SELECT(lvds->format) |
> +		     RK3568_LVDS0_MSBSEL(1));
> +
> +	return 0;
> +}
> +
> +static void rk3568_lvds_poweroff(struct rockchip_lvds *lvds)
> +{
> +	regmap_write(lvds->grf, RK3568_GRF_VO_CON2,
> +		     RK3568_LVDS0_MODE_EN(0) | RK3568_LVDS0_P2S_EN(0));
> +
> +	pm_runtime_put(lvds->dev);
> +}
> +
> +static void rk3568_lvds_encoder_enable(struct drm_encoder *encoder)
> +{
> +	struct rockchip_lvds *lvds = encoder_to_lvds(encoder);
> +	int ret;
> +
> +	drm_panel_prepare(lvds->panel);
> +
> +	ret = rk3568_lvds_poweron(encoder);
> +	if (ret) {
> +		DRM_DEV_ERROR(lvds->dev, "failed to power on LVDS: %d\n", ret);
> +		goto err_unprepare;
> +	}
> +
> +	/* The GRF must be in LVDS mode with dclk running before the phy. */
> +	ret = phy_set_mode(lvds->dphy, PHY_MODE_LVDS);
> +	if (ret) {
> +		DRM_DEV_ERROR(lvds->dev, "failed to set phy mode: %d\n", ret);
> +		goto err_poweroff;
> +	}
> +
> +	ret = phy_power_on(lvds->dphy);
> +	if (ret) {
> +		DRM_DEV_ERROR(lvds->dev, "failed to power on phy: %d\n", ret);
> +		goto err_poweroff;
> +	}
> +
> +	lvds->enabled = true;
> +	drm_panel_enable(lvds->panel);
> +	return;
> +
> +err_poweroff:
> +	rk3568_lvds_poweroff(lvds);
> +err_unprepare:
> +	drm_panel_unprepare(lvds->panel);
> +}
> +
> +static void rk3568_lvds_encoder_disable(struct drm_encoder *encoder)
> +{
> +	struct rockchip_lvds *lvds = encoder_to_lvds(encoder);
> +
> +	/*
> +	 * .enable() cannot report failure, so the atomic helpers call this even
> +	 * when it bailed out and already unwound itself. Tear down only what an
> +	 * enable that ran to completion left behind, or the phy power count and
> +	 * the runtime-PM count of a half-enabled encoder underflow.
> +	 */
> +	if (!lvds->enabled)
> +		return;
> +
> +	drm_panel_disable(lvds->panel);
> +	phy_power_off(lvds->dphy);
> +	rk3568_lvds_poweroff(lvds);
> +	drm_panel_unprepare(lvds->panel);
> +	lvds->enabled = false;
> +}
> +
>  static const
>  struct drm_encoder_helper_funcs rk3288_lvds_encoder_helper_funcs = {
>  	.enable = rk3288_lvds_encoder_enable,
> @@ -449,6 +544,13 @@ struct drm_encoder_helper_funcs px30_lvds_encoder_helper_funcs = {
>  	.atomic_check = rockchip_lvds_encoder_atomic_check,
>  };
>  
> +static const
> +struct drm_encoder_helper_funcs rk3568_lvds_encoder_helper_funcs = {
> +	.enable = rk3568_lvds_encoder_enable,
> +	.disable = rk3568_lvds_encoder_disable,
> +	.atomic_check = rockchip_lvds_encoder_atomic_check,
> +};
> +
>  static int rk3288_lvds_probe(struct platform_device *pdev,
>  			     struct rockchip_lvds *lvds)
>  {
> @@ -512,6 +614,17 @@ static int px30_lvds_probe(struct platform_device *pdev,
>  	return phy_power_on(lvds->dphy);
>  }
>  
> +static int rk3568_lvds_probe(struct platform_device *pdev,
> +			     struct rockchip_lvds *lvds)
> +{
> +	/* The phy is powered on from the encoder enable path, not here. */
> +	lvds->dphy = devm_phy_get(&pdev->dev, "dphy");
> +	if (IS_ERR(lvds->dphy))
> +		return PTR_ERR(lvds->dphy);
> +
> +	return phy_init(lvds->dphy);
> +}
> +
>  static const struct rockchip_lvds_soc_data rk3288_lvds_data = {
>  	.probe = rk3288_lvds_probe,
>  	.helper_funcs = &rk3288_lvds_encoder_helper_funcs,
> @@ -522,6 +635,11 @@ static const struct rockchip_lvds_soc_data px30_lvds_data = {
>  	.helper_funcs = &px30_lvds_encoder_helper_funcs,
>  };
>  
> +static const struct rockchip_lvds_soc_data rk3568_lvds_data = {
> +	.probe = rk3568_lvds_probe,
> +	.helper_funcs = &rk3568_lvds_encoder_helper_funcs,
> +};
> +
>  static const struct of_device_id rockchip_lvds_dt_ids[] = {
>  	{
>  		.compatible = "rockchip,rk3288-lvds",
> @@ -531,6 +649,10 @@ static const struct of_device_id rockchip_lvds_dt_ids[] = {
>  		.compatible = "rockchip,px30-lvds",
>  		.data = &px30_lvds_data
>  	},
> +	{
> +		.compatible = "rockchip,rk3568-lvds",
> +		.data = &rk3568_lvds_data
> +	},
>  	{}
>  };
>  MODULE_DEVICE_TABLE(of, rockchip_lvds_dt_ids);
> @@ -601,6 +723,8 @@ static int rockchip_lvds_bind(struct device *dev, struct device *master,
>  	encoder = &lvds->encoder.encoder;
>  	encoder->possible_crtcs = drm_of_find_possible_crtcs(drm_dev,
>  							     dev->of_node);
> +	rockchip_drm_encoder_set_crtc_endpoint_id(&lvds->encoder,
> +						  dev->of_node, 0, 0);
>  
>  	ret = drm_simple_encoder_init(drm_dev, encoder, DRM_MODE_ENCODER_LVDS);
>  	if (ret < 0) {
> diff --git a/drivers/gpu/drm/rockchip/rockchip_lvds.h b/drivers/gpu/drm/rockchip/rockchip_lvds.h
> index 2d92447..93d3415 100644
> --- a/drivers/gpu/drm/rockchip/rockchip_lvds.h
> +++ b/drivers/gpu/drm/rockchip/rockchip_lvds.h
> @@ -121,4 +121,14 @@
>  #define   PX30_LVDS_P2S_EN(val)			FIELD_PREP_WM16(BIT(6), (val))
>  #define   PX30_LVDS_VOP_SEL(val)		FIELD_PREP_WM16(BIT(1), (val))
>  
> +#define RK3568_GRF_VO_CON0			0x0360
> +#define   RK3568_LVDS0_SELECT(val)		FIELD_PREP_WM16(GENMASK(5, 4), (val))
> +#define   RK3568_LVDS0_MSBSEL(val)		FIELD_PREP_WM16(BIT(3), (val))
> +
> +#define RK3568_GRF_VO_CON2			0x0368
> +#define   RK3568_LVDS0_DCLK_INV_SEL(val)	FIELD_PREP_WM16(BIT(9), (val))
> +#define   RK3568_LVDS0_DCLK_DIV2_SEL(val)	FIELD_PREP_WM16(BIT(8), (val))
> +#define   RK3568_LVDS0_MODE_EN(val)		FIELD_PREP_WM16(BIT(1), (val))
> +#define   RK3568_LVDS0_P2S_EN(val)		FIELD_PREP_WM16(BIT(0), (val))
> +
>  #endif /* _ROCKCHIP_LVDS_ */

Reviewed-by: Chaoyi Chen <[email protected]>

-- 
Best, 
Chaoyi

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip