Re: [PATCH 00/10] Introduce Virtual IRQ (VIRQ) framework

On Mon, Jul 20, 2026 at 8:45 PM Raymond Mao <[email protected]> wrote:
>
> Hi Anup,
>
> On Mon, Jul 20, 2026 at 4:41 AM Anup Patel <[email protected]> wrote:
> >
> > On Fri, May 15, 2026 at 4:28 AM Raymond Mao <[email protected]> wrote:
> > >
> > > From: Raymond Mao <[email protected]>
> > >
> > > This series introduces a Virtual IRQ (VIRQ) framework for OpenSBI to
> > > support domain-aware wired interrupt couriering.
> > >
> > > The main use case is to let OpenSBI receive a host HWIRQ in M-mode,
> > > map it into a per-channel VIRQ number space, route it to a target
> > > domain, notify the target S-mode payload, and let that payload
> > > pop/complete the pending VIRQ through an SBI ecall interface.
> > >
> > > The implementation is organized as follows:
> > >
> > >   - add irqchip helpers for S-mode pending notification
> > >   - extend domain context switching to support VIRQ-driven
> > >     cross-domain couriering and return-to-previous-domain flow
> > >   - add the core VIRQ mapping, routing, and per-(domain,hart)
> > >     pending queue framework
> > >   - add a VIRQ vendor ecall extension for POP and COMPLETE
> > >   - parse sysirq routing rules from DT under /chosen/opensbi-domains
> > >   - derive APLIC target hart routing from sysirq nodes
> > >   - update the irqchip/APLIC path to support deferred completion and
> > >     per-HWIRQ APLIC targets
> > >   - document the DT binding and routing rules
> > >
> > > The DT routing model is based on "opensbi,mpxy-sysirq" nodes.
> > > Each interrupts-extended entry contributes one routed physical source,
> > > its entry index becomes the VIRQ number within the selected
> > > opensbi,mpxy-channel-id, and opensbi,domain selects the destination
> > > OpenSBI domain.
> > >
> > > This series depends on a previous patch set:
> > > [PATCH v2 1/3] lib: utils: irqchip: implement APLIC hwirq operation hooks
> > > https://lore.kernel.org/opensbi/[email protected]/#t
> > >
> > > Raymond Mao (10):
> > >   lib: irqchip: add S-mode notification helpers
> > >   lib: sbi: domain: adaptation for supporting VIRQ couriering domain
> > >     context switch
> > >   lib: sbi: Add Virtual IRQ (VIRQ) subsystem
> > >   lib: sbi: Add VIRQ ecall extension
> > >   lib: sbi: domain: add domain lookup by name
> > >   lib: utils: fdt: parse sysirq routing from DT
> > >   lib: utils: irqchip: derive APLIC targets from sysirq nodes
> > >   lib: irqchip: support deferred completion and per-HWIRQ APLIC targets
> > >   lib: sbi: domain: ensure boot_hartid is assigned
> > >   docs: domain: document sysirq VIRQ mapping and routing rules
> >
> > This VIRQ abstraction is not needed with the improved SBI irqchip
> > where each external interrupt (wired / MSI) can be uniquely identified
> > by a tuple which SBI irqchip instance and hwirq number in the instance.
> >
> > Also, the VIRQ ecall is ad-hoc and does not correspond to any
> > SBI extension.
> >
> > All-in-all the whole interrupt routing for supervisor domains must
> > be re-written using SBI MPXY + RPMI system irq service group
> > as the interface for supervisor domains.
> >
> > The SBI MPXY is already a ratified SBI extension and OpenSBI
> > already has an extensible MPXY framework with a number of MPXY
> > drivers under lib/utils/mpxy. The RPMI system irq draft specifcation
> > was already shared few months back.
> >
>
> As we discussed in the SSWG meeting, the plan to support the SBI MPXY
> + RPMI system irq service group is ongoing.
> It will be much appreciated if you can consider to merge this series
> to enable the interrupt routing first before I post a separate series
> for RPMI on top of this.
>

Like I explained above, you don't need this series for implementing
SBI MPXY + RPMI system irq service group.

Regards,
Anup

-- 
opensbi mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/opensbi