[PATCH v5 00/12] arm64: dts: rockchip: Add NanoPi M6 board

This patch series add support for the NanoPi M6. This board is very
similar to the NanoPi R6C and R6S boards which are already supported.

Main differences:
* M.2 M-key slot with PCIe (Also present on R6C)
* M.2 E-key slot with PCIe and USB (from hub)
* 1 additional USB 2.0 port from an on-board USB hub
* RT5616 audio CODEC

Patch 1 documents the NanoPi M6 board compatibility string
Patch 2 to 10 are fixes and additions to the nanopi-r6 base DT
Patch 11 extracts the common NanoPi 6 series bits from nanopi-r6 into
nanopi.dtsi
The final patch adds support for NanoPi M6. Support for M6 has been
split into two files; one dtsi and one dts file. This makes it easier
to add support to the new M6V2 board at a later stage.

All changes have been verified using the schematics for M6, R6C and R6S.
Only M6 have been boot and runtime tested. Testers for R6x are welcome.

Note that Sashiko may complain that u2phy0_otg is a dangling phandle in
patch 11. This will never happen in practice so it's safe to ignore.

Signed-off-by: Joachim Eastwood <[email protected]>
---
Changes in v5:
- Switch from simple-audio-card to audio-graph-card as Sashiko
  complains, rightfully, that the bindings are a mismash of both.
- Add pull-up on sd cd pin. Noticed by Diederik.
- Link to v4: https://patch.msgid.link/[email protected]

Changes in v4:
- Remove boot-on reintroduction on vdd_npu_s0 in nanopi.dtsi during
  refactor screw-up. Thanks to Sashiko for catching that.
- Fix minor typo in "add gmac1 add phy-supply" commit message
- Use schematic net names on PCIe reset lines. As suggested by Diederik.
- Link to v3: https://patch.msgid.link/[email protected]

Changes in v3:
- Reorder patches so the DT fixes/additions are applied to
  nanopi-r6.dtsi as suggested by Jonas Karlman
- Add comment to gmac to rgmii-rxid phy-mode to explain usage
- Addition of pinctrl to sd and pcie are now marked as fixes
- Remove both always-on and boot-on from NPU regulator
- Link to v2: https://patch.msgid.link/[email protected]

Changes in v2:
- Organize DT such that adding support to NanoPi M6V2 later is easier
- Use correct clk id for I2C mclk out as suggested by Diederik.
- Add a couple of acks from Krzysztof Kozlowski.
- Link to v1: https://patch.msgid.link/[email protected]

---
Joachim Eastwood (12):
      dt-bindings: arm: rockchip: add FriendlyElec NanoPi M6
      arm64: dts: rockchip: rk3588s-nanopi-r6: fix missing sdmmc cd pinctrl
      arm64: dts: rockchip: rk3588s-nanopi-r6: fix missing pcie rst pinctrl
      arm64: dts: rockchip: rk3588s-nanopi-r6: remove pull up on rtc int pin
      arm64: dts: rockchip: rk3588s-nanopi-r6: pcie2x1l2: add clkreq
      arm64: dts: rockchip: rk3588s-nanopi-r6: remove always-on and boot-on from vdd_npu_s0 reg
      arm64: dts: rockchip: rk3588s-nanopi-r6: remove useless vcc_3v3_pcie20
      arm64: dts: rockchip: rk3588s-nanopi-r6: add gmac1 phy-supply
      arm64: dts: rockchip: rk3588s-nanopi-r6: remove bogus vcc5v0_usb regulator
      arm64: dts: rockchip: rk3588s-nanopi-r6: add comment about gmac phy-mode
      arm64: dts: rockchip: rk3588s-nanopi-r6: refactor to support M6 boards
      arm64: dts: rockchip: add support for NanoPi M6 board

 .../devicetree/bindings/arm/rockchip.yaml          |   3 +-
 arch/arm64/boot/dts/rockchip/Makefile              |   1 +
 .../arm64/boot/dts/rockchip/rk3588s-nanopi-m6.dtsi | 142 ++++
 .../boot/dts/rockchip/rk3588s-nanopi-m6v1.dts      |  57 ++
 .../arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 792 +-------------------
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi.dtsi   | 797 +++++++++++++++++++++
 6 files changed, 1000 insertions(+), 792 deletions(-)
---
base-commit: dc59e4fea9d83f03bad6bddf3fa2e52491777482
change-id: 20260701-nanopi-m6-ffeef7252fd7

Best regards,
--  
Joachim Eastwood <[email protected]>