[PATCH v2 2/6] phy: qcom: sgmii-eth: vote for both voltage rails with correct current loads

The SerDes PHY has two voltage supply rails, vdda-0p9 and vdda-1p2,
that must both be enabled for calibration to succeed. Without them:

  qcom-dwmac-sgmii-phy 8909000.phy: QSERDES_COM_C_READY_STATUS timed-out
  qcom-ethqos 23040000.ethernet eth0: __stmmac_open: Serdes powerup failed

The driver relied solely on the PHY framework's implicit enable of
'phy-supply', which only voted for a single rail and set no current
load. Use devm_regulator_bulk_get_const() to acquire both supplies and
set the peak current loads (46 mA for vdda-0p9, 15 mA for vdda-1p2)
as required by the hardware.

Fixes: 601d06277007 ("phy: qcom: add the SGMII SerDes PHY driver")
Signed-off-by: Mohd Ayaan Anwar <[email protected]>
---
 drivers/phy/qualcomm/phy-qcom-sgmii-eth.c | 37 +++++++++++++++++++++++++++----
 1 file changed, 33 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-sgmii-eth.c b/drivers/phy/qualcomm/phy-qcom-sgmii-eth.c
index f48faa2929a682be6024ee349fac6fd1b6464cb3..7137200c3f310a4d2642bb9bdbe3adb7589b2241 100644
--- a/drivers/phy/qualcomm/phy-qcom-sgmii-eth.c
+++ b/drivers/phy/qualcomm/phy-qcom-sgmii-eth.c
@@ -11,6 +11,7 @@
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
 
 #include "phy-qcom-qmp-pcs-sgmii.h"
 #include "phy-qcom-qmp-qserdes-com-v5.h"
@@ -26,7 +27,15 @@
 #define QSERDES_PCS_SGMIIPHY_READY			BIT(7)
 #define QSERDES_COM_C_PLL_LOCKED			BIT(1)
 
+static const struct regulator_bulk_data qcom_dwmac_sgmii_phy_vregs[] = {
+	{ .supply = "vdda-0p9", .init_load_uA = 46000 },
+	{ .supply = "vdda-1p2", .init_load_uA = 15000 },
+};
+
+#define QCOM_SGMII_NUM_SUPPLIES		ARRAY_SIZE(qcom_dwmac_sgmii_phy_vregs)
+
 struct qcom_dwmac_sgmii_phy_data {
+	struct regulator_bulk_data *vregs;
 	struct regmap *regmap;
 	struct clk *refclk;
 	phy_interface_t interface;
@@ -273,13 +282,24 @@ static int qcom_dwmac_sgmii_phy_power_on(struct phy *phy)
 	struct qcom_dwmac_sgmii_phy_data *data = phy_get_drvdata(phy);
 	int ret;
 
-	ret = clk_prepare_enable(data->refclk);
-	if (ret < 0)
+	ret = regulator_bulk_enable(QCOM_SGMII_NUM_SUPPLIES, data->vregs);
+	if (ret)
 		return ret;
 
+	ret = clk_prepare_enable(data->refclk);
+	if (ret)
+		goto err_disable_regulators;
+
 	ret = qcom_dwmac_sgmii_phy_calibrate(phy);
-	if (ret < 0)
-		clk_disable_unprepare(data->refclk);
+	if (ret)
+		goto err_disable_clk;
+
+	return 0;
+
+err_disable_clk:
+	clk_disable_unprepare(data->refclk);
+err_disable_regulators:
+	regulator_bulk_disable(QCOM_SGMII_NUM_SUPPLIES, data->vregs);
 
 	return ret;
 }
@@ -296,6 +316,8 @@ static int qcom_dwmac_sgmii_phy_power_off(struct phy *phy)
 
 	clk_disable_unprepare(data->refclk);
 
+	regulator_bulk_disable(QCOM_SGMII_NUM_SUPPLIES, data->vregs);
+
 	return 0;
 }
 
@@ -357,6 +379,7 @@ static int qcom_dwmac_sgmii_phy_probe(struct platform_device *pdev)
 	struct phy_provider *provider;
 	void __iomem *base;
 	struct phy *phy;
+	int ret;
 
 	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
 	if (!data)
@@ -381,6 +404,12 @@ static int qcom_dwmac_sgmii_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(data->refclk))
 		return PTR_ERR(data->refclk);
 
+	ret = devm_regulator_bulk_get_const(dev, QCOM_SGMII_NUM_SUPPLIES,
+					    qcom_dwmac_sgmii_phy_vregs,
+					    &data->vregs);
+	if (ret)
+		return ret;
+
 	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 	if (IS_ERR(provider))
 		return PTR_ERR(provider);

-- 
2.34.1